Kendall Howard Performance Series User manual

www.cablesmanager com.
Performance Series® LAN Station /
Workbench Instructions

Welcome to your new Kendall Howard Performance Series®
LAN Station / Workbench. Here is a little information to get you started
on assembling your LAN Station / Workbench.
This instruction manual goes over the complete assembly of all four of the standard congurations. Please
pay close attention to the series that you have purchased and follow along making sure you follow the
steps that only pertain to your series. If you need to identify which series you have purchased, please
reference the chart below by matching it with the SKU / Part Number listed on the crate.
As always, if you have any questions or concerns please reach out to us in any of the following ways:
EMAIL: info cablesmanager.com@
websit :www.cablesmanager.come .
100 Series
Half Bottom Shelf & Two Upper Shelves
200 Series
Full Bottom Shelf & Two Upper Shelves
300 Series
Full Bottom Shelf & No Upper Shelves
400 Series
Half Bottom Shelf & No Upper Shelves
www.cablesmanager.com

What’s in the Crate?
Left Upper Shelf Support Right Upper Shelf Support
Left Leg Right Leg
Cross Bar Upper Shelf Channel
QTY 2
Work Surface
QTY 1
Lower Shelf Upper Shelf
Channel Nut
QTY 8
1 1/2” x 1 1/2”End Cap
QTY 4
1 1/2” x 2”End Cap
QTY 4
3/4” Round End Cap
QTY 14
Leveler
QTY 4
1/4-20 Cross Head Screw - Silver
QTY 14
2 1/2” Bolt - Black
QTY 4
1 1/2” Bolt - Black
QTY 18
Back Plate
QTY 1
*If you are using a cordless drill, be sure to adjust the speed and
slip so you do not cross thread or over tighten the screws.
Tools Needed:
T -Handle Hex
Wrench
(Included)
Phillips Head
Screwdriver
Cordless
Drill*

Step 1 - ALL SERIES
*Please note that the number of screw locations varies by the size of the bench.
Picture below is of a 48”bench.
Step 2 - ALL SERIES
Step 3 - ALL SERIES
Work Surface
Cross Bar(s) 1/4-20 Screw(s)
Right Leg
Left Leg
1 1/2” Bolt(s)
*Make sure you are using the 1 1/2”size and not the 2 1/2” size.
Lower Shelf
(Half Bottom)
100 & 400 SERIES
1/4-20 Screw(s)
Step 4 -
*Please note that the number of screw locations varies by the size of the bench.
Picture below is of a 48”bench.
Step 5 - ALL SERIES Step 6
Rotate
1 1/2” Bolt(s)
Lower Shelf with 2 Cross Bars
Cross Bar(s)
Lower Shelf with 1 Cross Bars
1 1/2” Bolt(s)
Lower Shelf
(Second shelf to
make full bottom)
200 & 300 SERIES
100 & 400 SERIES only have one bottom shelf.
200 & 300 SERIES have two bottom shelves.
ONLY FOR 200 & 300 SERIES which have the
full bottom shelf.
100 SERIES & 400 SERIES skip this step.

Step 2 - ALL SERIES Step 7 - ALL SERIES Step 8
Step 6
Step 9 Step 10
Step 11 Step 12
Leveler(s)
*If you purchased the optional caster kit, install the casters
instead of the levelers.
Rotate
2 1/2” Bolt(s)
*You will need the 2 1/2”bolts
so they are long enough to go
into the vertical channels.
Channel Nut(s)
Back Plate
Leave Space
Upper Shelf Channel(s)
Adjust height and
tighten bolts.
Highest
Lowest
Left Upper
Shelf Support(s)
Right Upper
Shelf Support(s)
Channel Nut(s)
1 1/2” Bolt(s)
Note - the larger
hole(s) on the
shelf supports
face the outside.
- TIP -
The teeth of the channel
nut always face toward
the bolt.
This completes the assembly for the
300 SERIES & 400 SERIES!
For the 100 SERIES & 200 SERIES
continue to STEP 9.
- TIP -
100 SERIES & 200 SERIES 100 SERIES & 200 SERIES
100 SERIES & 200 SERIES 100 SERIES & 200 SERIES

Step 14
Step 15
Step 16
Upper Shelves
Cross Bar(s)
1/4-20 Screw(s)
Upper Shelf Assemblies
1 1/2” Bolt(s)
3/4” Round End Cap(s)
1 1/2” x 1 1/2” End Cap(s)
1 1/2” x 2” End Cap(s)
This completes the assembly for the
300 SERIES & 400 SERIES!Step 13
*Please note that the number of screw locations varies by the size of the bench.
Picture below is of a 48”bench.
100 SERIES & 200 SERIES 100 SERIES & 200 SERIES
100 SERIES & 200 SERIES
100 SERIES & 200 SERIES

Step 14
DISCLAIMER: Kendall Howard LLC. endeavors to make this manual accurate and complete. However, Kendall
Howard LLC makes norepresentations or warranties of any kind, expressed or implied, about whether the use
of products contained herein would infringe any rights or the correctness, accuracy or reliabilityof the infor-
mation contained hereinor that said information covers all details, conditions or variations.The information
herein does not provide for every possible contingency in connection with the installation or use of the
product(s). The information contained in this document is subject to change without notice or obligation. 
Kendall Howard LLC assumes no responsibility for the accuracy, completeness orreliability of the information
contained in this document. Any reliance placed on the information is therefore strictly at your own risk.