Kenwood MG450 User manual

Kenwood Limited, New Lane, Havant, Hampshire PO9 2NH, UK
www.kenwoodworld.com 9803/4

MG450/MG470
KENWOOD
O
I

UNFOLD

UNFOLD

UNFOLD




KENWOOD



q
p
o
n
m
l
i
h
k

j
KENWOOD
O
I
a
b
c
d
e
f
g


KENWOOD
KENWOOD

r
s
t
10
11
12

KENWOOD
u
v
15
16
KENWOOD
14
13

safety
●Always ensure bones and rind etc
are removed from the meat before
mincing.
●When mincing nuts only feed a few
down at a time and allow the scroll
to pick them up before adding any
more.
●Always unplug:
●●before fitting or removing parts
●●after use
●●before cleaning.
●Always use the pusher supplied.
Never put your fingers or utensils in
the feed tube.
●Warning - the cutting blade is sharp,
handle with care both in use and
cleaning.
●Ensure the attachment is secured in
position before switching on.
●To avoid electric shocks, never let
the power unit, cord or plug get wet.
●Never use a damaged mincer. Get it
checked or repaired: see ‘Service’.
●Never use an unauthorised
attachment.
●Never let the cord hang down where
a child could grab it - wrap excess
cord around the bracket at the back
of the machine.
●This mincer is not intended for use
by young children or infirm persons
without supervision.
●Young children should be supervised
to ensure they do not play with the
appliance.
●Only use the machine for its
intended domestic use.
before plugging in
●Make sure your electricity supply is
the same as the one shown on the
underside of your machine.
Important (UK) only
●The wires in the cord are coloured
as follows:
Blue = Neutral
Brown = Live.
●This machine complies with
European Economic Community
Directive 89/336/EEC.
before using for the first time
1Remove all packaging.
2Wash the parts see ‘care and
cleaning’
3Wrap excess cord around the
bracket at the back of the mincer.
mincer
power unit
attachment outlet
locking screw
on/off switch
screen storage
reverse switch
bracket for excess cord
spanner
ring nut
mincer screens: fine, medium,
coarse
cutter
scroll
mincer body
tray
pusher
pusher lid
dish/cover
to assemble
1Fit the scroll inside the mincer body.
2Fit the cutter – cutting side
outermost . Ensure it’s seated
properly – otherwise you
could damage your mincer.
3Fit a mincer screen . Put the notch
over the pin.
●Use the fine screen for raw meat;
fish; small nuts; or cooked meat for
shepherd’s pie or meat loaves.
●Use the medium and coarse screens
for raw meat; fish; nuts; vegetables;
hard cheese; or peel or dried fruit for
puddings and marmalade.
4Loosely fit the ring nut.
English
4
k
m
l
b
c
d
e
f
g
h
i
j
n
o
p
q
a

to use the mincer
1Release the locking screw by turning
anticlockwise , then slide the
attachment into the outlet .
2Turn it both ways until it locks into
place. Then turn the locking screw
clockwise to secure.
3Tighten the ring nut manually.
4Fit the tray. Put the dish/cover under
the mincer to catch the food.
5Thaw frozen food thoroughly
before mincing. Cut meat into
2.5cm (1”) -wide strips.
6Switch on . Using the pusher,
gently push the food through, one
piece at a time. Don’t push hard
– you could damage your
mincer.
●If the machine stalls or jams during
use, switch off. Depress the reverse
switch  for a few seconds to
release the clogged food. Unplug
and remove any clogged material.
sausage filler
base plate*
large nozzle* (for thick sausages)
small nozzle* (for thin sausages)
*Stored in the pusher
Ask your butcher for sausage skin or
mail order from the Natural Casing
Company Ltd, PO Box 133,
Farnham, Surrey GU10 5HT,
England. Use pig/hog skin on the
large nozzle and sheep/lamb skin on
the small nozzle. Or, instead of using
skin, roll in breadcrumbs or
seasoned flour before cooking.
to use the sausage filler
1If you’re using skin, soak it in cold
water for 30 minutes first.
2Release the locking screw by turning
anticlockwise , then slide the
attachment into the outlet .
3Turn it both ways until it locks into
place. Then turn the locking screw
clockwise to secure.
4Fit the scroll inside the mincer body.
5Fit the base plate - put the notch
over the pin.
6If you’re using skin, open it up with a
jet of water. Then put your chosen
nozzle under a running tap and pull
the skin onto the nozzle.
7Hold the nozzle on the mincer and
screw the ring nut on .
8Fit the tray.
9Switch on. Using the pusher, push
the food through. Don’t push
hard – you could damage your
mincer. Ease the skin off the nozzle
as it fills. Don’t overfill.
10Twist the skin to form sausages.
pork sausage recipe
100g (4oz) dry bread
600g (11⁄2lb) pork, lean and fat, cut
into strips
1 egg, beaten
5ml (1tsp) mixed herbs
salt and pepper
1Soak the bread in water, then
squeeze.
2Mince the pork into a bowl.
3Add the remaining ingredients and
mix well.
4Make into sausages (see above).
5Fry, grill or bake until golden brown.
kebbe maker
shaper*
cone*
*Stored in the pusher
Kebbe is a traditional Middle Eastern
dish: deep-fried lamb-and-bulgur-
wheat parcels with a minced meat
filling.
to use the kebbe maker
1Release the locking screw by turning
anticlockwise , then slide the
attachment into the outlet .
2Turn it both ways until it locks into
place. Then turn the locking screw
clockwise to secure.
5
r
s
t
u
v
10
11
12
13
14

3Fit the scroll inside the mincer body.
4Fit the shaper – put the notch
over the pin.
5Fit the cone .
6Screw the ring nut on.
7Fit the tray.
8Switch on. Using the pusher, gently
push your mixture through. Cut into
lengths.
stuffed kebbe recipe
outer casing
500g (1lb 2oz) lamb or fat-free
mutton, cut into strips
500g (1lb 2oz) bulgur wheat,
washed and drained
1 small onion
1Using the fine screen, mince
alternative batches of meat and
wheat, adding the onion before the
last batch.
2Mix. Then mince twice more.
3Push through, using the kebbe
maker (see above).
Filling
400g (10oz) lamb, cut into strips
15ml (1tbsp) oil
2 medium onions, finely chopped
5-10ml (1-2tsp) ground allspice
15ml (1tbsp) plain flour
salt and pepper
1Using the fine screen, mince the
lamb.
2Fry the onions until golden brown.
Add the lamb.
3Add the remaining ingredients and
cook for 1-2 minutes.
4Drain off any excess fat and allow to
cool.
To finish
1Push the casing mixture through,
using the kebbe maker.
2Cut into 8cm (3”) lengths.
3Pinch one end of the tube to seal it.
Push some filling – not too much –
into the other end, then seal.
4Deep fry in hot (190˚) oil for about 6
minutes or until golden brown.
care and cleaning
power unit
Wipe with a damp cloth, then dry.
mincer attachment
1Loosen the ring nut manually or with
the spanner and dismantle. Wash
all the parts in hot soapy water, then
dry. Don’t wash any part in the
dishwasher. Never use a soda
solution.
2Re-assemble.
3Wipe the screens with vegetable oil,
then wrap in greaseproof paper to
prevent discolouring/rusting.
There is storage space for 2 screens
on the power unit .
4Ifyou keep the mincer on the
machine, put the dish/cover on the
tray as a dust-cover.
5You can pull the lid off the pusher
and store the sausage and kebbe
attachments inside.
service and customer
care
●If the cord is damaged it must, for
safety reasons, be replaced by
Kenwood or an authorised Kenwood
repairer.
UK
If you need help with:
●using your machine or
●servicing, spare parts or repairs (in or
out of guarantee)
call Kenwood customer care on 023
9239 2333. Have your model
number ready – it’s on the
underside of the power unit.
●spares and attachments
call 0870 2413653.
other countries
●Contact the shop where you bought
your machine.
6
16
15

guarantee
If your mincer goes wrong within one
year from the date you bought it, we
will repair it (or replace it if
necessary) free of charge provided:
●you have not misused, neglected or
damaged it;
●it has not been modified (unless by
Kenwood);
●it is not second-hand;
●it has not been used commercially;
●you have not fitted a plug incorrectly;
and
●you supply your receipt to
show when you bought it.
This guarantee does not affect your
statutory rights.
7