Keys Fitness Leg Machine KF-LEGM User manual

Leg Machine
Owner’s Manual
KF-LEGM
215-00129
10/06 Rev A

2
Table Of Contents
Before You Start 3
Important Safety Information 4
Assembly 5-11
Parts List 11
Exploded View 12
Warranty Information 13

KEYS FITNESS SERIES
MODEL: KF-LEGM
QUESTIONS?
CALL
1-888-340-0482
Monday-Friday
8:30-5:30 Central Time
When calling please have the following product information available:
3
Model Name :
Date Mfg.:
PO # :
Serial #:
Model Name Decal Location
THANK YOU for making this unit a part of your exercise program.
Keys Fitness assures the very best in value, appearance, durability
and biomechanics.
This manual will guide you through the assembly process. If at any time you are
having trouble with the assembly or use of this product, then please contact us
at our Keys Fitness Help line. We have trained service technicians on site to take
care of you, our valued customer.
REGISTRATION CARD
To avoid unnecessary delays in warranty parts and to insure that a permanent
record of your purchase is on file with our company, be sure to send in the war-
ranty registration card or register on-line at www.keysfitness.com within 10 days
of purchase.
Before You Start

4
Important Safety Information
Prior to assembly, remove components from the box and verify that all the listed parts were
supplied.
WARNING!
Before using this unit or starting any exercise program, consult your
physician. This is especially important for persons over the age of
35 and/or persons with pre-existing health problems. Keys Fitness
Products LP assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
It is the owner’s responsibility to ensure that all users of this unit have
read the Owner’s Manual and are familiar with safety information and
precautions.
SAFETY PRECAUTIONS
• This unit should only be used on a level surface and is intended for
indoor use only. Keys Fitness recommends an equipment mat be
placed under the unit to protect the floor or carpet and for easier
cleaning.
• Wear comfortable, good-quality walking or running shoes and appro-
priate clothing. Do not use this unit with bare feet, sandals, socks or
stockings!
• Always examine your unit before using to ensure all parts are in
working order.
• Do not leave children unsupervised near or on the unit.
• Service to your unit should only be performed by an authorized
service representative, unless authorized and/or instructed by a
Keys Fitness technician. Failure to follow these instructions will void
the warranty.
NOTE:Hand tighten bolts and nylon nuts until machine is fully assembled.
Read all precautions and instructions in this manual before using this equipment.

Assembly
5

STEP 1
Connect Front Frame (3) and Rear Base (2) to Main Frame
(1) using:
4 x (19) Bolt
8 x (18) Washer
4 x (20) Nylon Lock Nut
6
NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled.
Assembly

STEP 2
Connect Swing Tube (8) to Swing Arm as shown using:
1 x (37) Collar
1 x (34) Bolt
Slide Big Roller Pad (39) onto Swing Tube (8) and secure
using:
1 x (37) Collar
1 x (34) Bolt
7
NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled.
Assembly

STEP 3
Attach Right and Left Handles (11,12) using:
2 x (19) Bolt 4 x (18) Washer
2 x (20) Nylon Lock Nut
STEP 4
Attach Side Angle Frame (4) using:
4 x (19) Bolt 8 x (18) Washer
4 x (20) Nylon Lock Nut 2 x (21) Plate
STEP 5
Slide Stopper Prone (17) into Front Frame for range of
motion limiter.
8
NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled.
Assembly

STEP 6
Complete Adjustable Roller Pad Frame (10) as shown
using:
2 x (43) Foam Pad
2 x (33) Big Plug
Slide into frame and secure with Pop Pin.
Note: It is suggested that a rubber mallet be used to
secure plugs.
STEP 7
Slide Back Pad Adjustable Frame (9) into frame and secure
with Pop Pin.
9
NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled.
Assembly

STEP 8
Attach Back Pad (16) using:
2 x (28) Bolt 2 x (27) Washer
Connect Seat Pad (15) to Adjustable Seat Bracket (13)
using:
4 x (28) Bolt 4 x (27) Washer
Connect Adjustable Seat Bracket (13) to frame as shown
using:
1 x (14) Shaft with Screw End 2 x (18) Washer
2 x (20) Nylon Lock Nut 1 x (32) L Pin
10
NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled.
Assembly