Keys Fitness Cable Crossover KF-CC User manual

Owner’s Manual
215-00132
11/06 Rev A
Cable Crossover
KPS-CC

2
Table of Contents
Before You Start 3
Important Safety Information 4
Assembly 5-12
Parts List 13
Exploded View 14
Warranty Information 15

KEYS FITNESS SERIES
MODEL: KF-CC
QUESTIONS?
CALL
1-888-340-0482
Monday-Friday
8:30-5:30 Central Time
When calling please have the following product information available:
3
Model Name :
Date Mfg.:
PO # :
Serial #:
Model Name Decal Location
THANK YOU for making this unit a part of your exercise program.
Keys Fitness assures the very best in value, appearance, durability
and biomechanics.
This manual will guide you through the assembly process. If at
any time you are having trouble with the assembly or use of this product, then
please contact us at our Keys Fitness Help line. We have trained service techni-
cians on site to take care of you, our valued customer.
REGISTRATION CARD
To avoid unnecessary delays in warranty parts and to ensure that a permanent
record of your purchase is on file with our company, be sure to send in the war-
ranty registration card or register on-line at www.keysfitness.com within 10 days
of purchase.
Before You Start

Read all precautions and instructions in this manual before using this equipment.
NOTE:Hand tighten bolts and nylon nuts until machine is fully assembled.
SAFETY PRECAUTIONS
WARNING!
Prior to assembly, remove components from the box and verify that all the listed parts were
supplied.
4
Important Safety Information
Before using this unit or starting any exercise program, consult your
physician. This is especially important for persons over the age of
35 and/or persons with pre-existing health problems. Keys Fitness
Products LP assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
It is the owner’s responsibility to ensure that all users of this unit have
read the Owner’s Manual and are familiar with safety information and
precautions.
• This unit should only be used on a level surface and is intended for
indoor use only. Keys Fitness recommends an equipment mat be
placed under the unit to protect the floor or carpet and for easier
cleaning.
• Wear comfortable, good-quality walking or running shoes and appro-
priate clothing. Do not use this unit with bare feet, sandals, socks or
stockings!
• Always examine your unit before using to ensure all parts are in
working order.
• Do not leave children unsupervised near or on the unit.
• Service to your unit should only be performed by an authorized
service representative, unless authorized and/or instructed by a
Keys Fitness technician. Failure to follow these instructions will void
the warranty.

Step 1
Attach Middle Base (2) to Left Rear Upright (4) and Inner Base (1) using Bolts (42), Washers
(53) and Nylon Lock Nuts (54).
5
Assembly
NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled.

Step 2
Attach Middle Base (2) to Right Rear Upright (3) and Inner Base (1) using Bolts (42), Washers
(53) and Nylon Lock Nuts (54).
6
NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled.

Step 3
NOTE: Before completing any other steps, you should position noth ends of the unit 12 ft
apart from each other to accommodate the Cross Tube (11). This will keep you from having to
move the unit once it is loaded with weights.
Slide Weight Bumpers (38) and Guide Rods (9) onto holes of Middle Base (2).
Slide quantity 9 of the 10 lb. plates (33) onto guide rods. Then slide quantity 10 of the 5 lb.
plates (34) onto guide rods.
Slide Top Plate (32) onto top of weight stack. Insert Weight Pin (35)
Repeat STEP 3 on other side.
Assembly
NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled.
7

Step 4
Insert Left Slide Frame (6) onto Slide Guide Tube (5) as shown and lock into one of the holes
in tube.
Attach Slide Guide Tube (5) to Inner Base (1) with Bolt (41), Washers (53) and Nylon Lock Nut
(54).
Slide Top Frame (8) onto Guide Rods (9) and Slide Guide Tube (5) and connect as shown, using
Bolts (46), Washers (53), Nylon Locknut (54) and Bolt (44).
Secure Top Frame (8) to Left Upright (4) using Bolts (40), Washers (53) and Nylon Lock Nuts
(54).
8
Assembly
NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled.

Step 5
Insert Right Slide Frame (7) onto Slide Guide Tube (5) as shown and lock into one of the holes
in tube.
Attach Slide Guide Tube (5) to Inner Base (1) with Bolt (41), Washers (53) and Nylon Lock Nut
(54).
Slide Top Frame (8) onto Guide Rods (9) and Slide Guide Tube (5) and connect as shown, using
Bolts (46), Washers (53), Nylon Locknut (54), and Bolt (41).
Secure Top Frame (8) to Right Upright (3) using Bolts (40), Washers (53) and Nylon Lock Nuts
(54).
9
Assembly
NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled.

Step 6
Slide Top Cross Tube (11) into both sides of the Top Frame (8) and secure as shown, using
Bolts (41), Washers (53) and Nylon Lock Nuts (54). Note: two people will be needed to com-
plete this step safely.
Connect Chin-Up Handle (16) to Top Cross Tube (11) using Bolts (48), Washers (53) and Nylon
Lock Nuts (54).
10
Assembly
NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled.