Keys Fitness CABLE CROSSOVER KPS-CC User manual

O W N E R ’ S M A N U A L
CABLE CROSSOVER
Questions?
Call our toll free Keys Fitness Helpline
1-800-683-1236
KPS-CC

V
THANK YOU for making this Power System unit a part of
your exercise program. Keys Fitness and our Power System
Series assures the very best in value, appearance, durability
and biomechanics.
This manual will guide you through the assembly process. If at any time
you are having trouble with the assembly or use of this product, then
please contact us at our Keys Fitness Helpline. We have trained service
technicians on site to take care of you, our valued customer.
POWER SYSTEM SERIES
MODEL: KPS-CC
QUESTIONS?
CALL
1-800-683-1236
Monday-Friday
8:30-5:30 Central Time
When calling please have the following product information available:
• Product Series
• Model #
• Part Number
• Part Description
REGISTRATION CARD
To avoid unnecessary delays in warranty parts and to insure that a perma-
nent record of your purchase is on file with our company, be sure to send
in the warranty registration card or register on-line at www.keysfitness.com
within 10 days of purchase.

X
BEFORE YOU START
Prior to assemby, remove components from the box and verify that all the listed parts
were supplied.
Before using this unit or starting any exercise program, consult your physician. This is
especially important for persons over the age of 35 and/or persons with pre-existing
health problems. Keys Fitness Products LP assumes no responsibility for personal
injury or property damage sustained by or through the use of this product.
It is the owner’s responsibility to ensure that all users of this unit have read the Owner’s
Manual and are familiar with safety information and precautions.
SAFETY INFORMATION WARNING!
SAFETY PRECATIONS
• This Power System unit should only be used on a level surface and is intended for
indoor use only. Keys Fitness recommends an equipment mat be placed under the
unit to protect the floor or carpet and for easier cleaning.
• Wear comfortable, good-quality walking or running shoes and appropriate clothing.
Do not use this unit with bare feet, sandals, socks or stockings!
• Always examine your unit before using to ensure all parts are in working order.
• Do not leave children unsupervised near or on the unit.
• Service to your Power System unit should only be performed by an authorized serv-
ice representative, unless authorized and/or instructed by a Keys Fitness technician.
Failure to follow these instructions will void the warranty.

ASSEMBLY
Y
NOTE: Hand tighten bolts and nylon nuts until STEP 8.
STEP 1
Attach Middle Base (2) to Left Rear Upright (4)
and Inner Base (1) using Bolts (42), Washers (53)
and Nylon Lock Nuts (54).

Z
ASSEMBLY
NOTE: Hand tighten bolts and nylon nuts until STEP 8.
STEP 2
Attach Middle Base (2) to Right Rear Upright
(3) and Inner Base (1) using Bolts (42),
Washers (53) and Nylon Lock Nuts (54).

ASSEMBLY
NOTE: Hand tighten bolts and nylon nuts until STEP 8.
STEP 3
NOTE: Before completing any other
steps, you should position each side
of the unit where it will stay once fully
assembled such that the total length
is 12 feet long. This will keep you
from having to move the unit once it
is loaded with weights.
Slide Weight Bumpers (38) and
Guide Rods (9) into holes of Middle
Base (2).
Slide quantity 9 of the 10 lb plates
(33) onto guide rods. Then slide
quantity 10 of the 5 lb plates (34)
onto guide rods.
Slide Top Plate (32) onto top of
weight stack.
Repeat STEP 3 on other side.
[

\
ASSEMBLY
NOTE: Hand tighten bolts and nylon nuts until STEP 8.
STEP 4
Slide Left Slide Frame (6)
onto Slide Guide Tube (5) as
shown and lock into one of
the holes in tube.
Attach Slide Guide Tube (5)
to Inner Base (1) with Bolt
(41), Washers (53) and
Nylon Lock Nut (54).
Slide Top Frame (8) onto
Guide Rods (9) and Slide
Guide Tube (5) and connect
as shown.

ASSEMBLY
NOTE: Hand tighten bolts and nylon nuts until STEP 8.
STEP 5
Slide Right Slide Frame (7) onto
Slide Guide Tube (5) as shown and
lock into one of the holes in tube.
Attach Slide Guide Tube (5) to Inner
Base (1) with Bolt (41), Washers (53)
and Nylon Lock Nut (54).
Slide Top Frame (8) onto Guide
Rods (9) and Slide Guide Tube (5)
and connect as shown.
]

ASSEMBLY
NOTE: Hand tighten bolts and nylon nuts until STEP 8.
STEP 6
Slide Top Cross Tube (11) into both sides of the Top
Frame (8) and secure as shown. Note: two people will
be needed to complete this step safely.
Connect Chin-Up Handle (16) to Top Cross Tube (11)
using Bolts (48), Washers (53) and Nylon Lock Nuts
(54).
^

ASSEMBLY
NOTE: Hand tighten bolts and nylon nuts until STEP 8.
STEP 7
Insert Cable (15) and pulleys
and secure as shown.
NOTE: The weight stack is
not shown for better viewing of
cable instructions.
u