Kilotech KWD 15K User manual

KWD 15K KWD 30K MAN08152022
KWD 15K KWD 30K OPERATION MANUAL E MAN08152022
Ce manuel est disponible en français à http://www.kilotech.com
K851240 KWD 15K 15kgx1g/30lbx0.002lb/480ozx0.05oz
GTIN 888960512401
K851241 KWD 30K 30kgx2g/60lbx0.005lb/960ozx0.1oz
GTIN 888960512418
KWD 15K
KWD 30K
Owner’s Manual

1
TABLE OF CONTENTS
Introduction ................................................................................................... 2
Product Specification ................................................................................... 4
OPERATION .................................................................................................... 5
MAINTENANCE .............................................................................................. 9
ERROR AND STATUS MESSAGE.................................................................. 10

2
Introduction
◼Thank you
Thank you for choosing a Kilotech Scale. We appreciate your business and hope that you will
enjoy using your scale. Should you require support, please contact your local dealer where you
purchased.
◼Safety Precautions
Please follow these safety precautions:
• Verify AC Adapter input voltage matches the local AC power supply.
• Do not insert liquids or foreign objects.
• Do not operate the scale in hostile environments.
• Do not drop loads or leave a permanent load on the platform. This may damage the
measuring system.
• Do not place the scale upside down on the pan.
• Do not open the scale. Never attempt to make repairs yourself because this could be
dangerous. The warranty is void if this stipulation is ignored. The scale may only be opened by
authorized personnel.
• Always disconnect the device from the power supply before installing, servicing, cleaning or
performing maintenance.
• Check the power cable regularly for damage. If it is damaged, immediately disconnect the
device from the power supply.
◼Package Contents
• Scale
• AC Power Adaptor
• User’s Manual
Scale
User’s Manual
AC Power Adaptor

3
◼Parts Description
◼Selecting a Location
Select a firm, vibration-free and horizontal location for the scale. Avoid locations with direct
sunlight, excessive air currents, heat sources, or rapid temperature fluctuations.
◼Power
Connect the AC Adaptor to the AC mains supply. Connect the plug to the AC jack at the bottom
of the scale as shown in the illustration below. The power outlet should be close to the scale and
easily accessible.
◼Battery Power
The scale will automatically switch to battery operation if there is a power failure or the power
cord is removed to provide uninterrupted scale operation.
Note: When low battery is displayed, the scale will shut off after 30 seconds.
CAUTION:
Risk of explosion can occur if replaced with the wrong type or connected improperly.
Do not disassemble, repair or otherwise manipulate the battery socket.
Obey the local laws and regulations when disposing of the battery.
LCD Display
Key Pad
Battery Indicator
Stainless Steel Pan

4
Product Specification
◼Specifications
MODEL
KWD 15K
KWD 30K
Capacity
15kg x 0.001kg
30lb x 0.002lb
480oz x 0.05oz
30kg x 0.002kg
60lb x 0.005lb
960oz x 0.1oz
Graduation
1 g
2 g
Weighing Units
kg/lb/oz
Power Requirements
100 V - 240 V DC 15V / 0.3A AC adapter
4-AA batteries
Display
1.4 in LCD with Red and Green backlight
5-digit 7-Segment, Character height 25 mm/ 1 in
Key Function
4 Keys
On / Off, Unit, Target / Hold, Tare / Backlight
Operating Temperature
0°C to 40° C
Application Mode
Weighing, Check-weighing
Construction
304 Stainless Steel housing and platform with ABS plastic bottom
Platform Size
245 x 195 mm
Assembled Dimensions
285 x 255 x 90 mm
Weight
3.7 kg
◼
Warranty
Kilotech scales are warranted against defects in material and workmanship for a period of one
(1) year for the scale and 3 months for the adapter, from the date of purchase.
Please retain your receipt as proof of purchase. Warranty expiration on products returned
without proof of purchase will be determined from the manufacturing date code or the date of
shipment to the authorized dealer. Coverage may be invalidated as this date is previous to
purchase date. No other express or implied warranty is given by Kilotech.
Freight damage on returns is not covered under warranty.
This warranty does not apply for the following reasons: the product has been damaged by
accident or misuse, parts and products of a consumable nature, exposed to radioactive or
corrosive materials, has foreign material penetrating to the inside of the product, or as a result of
service or modification by other than Kilotech.

5
OPERATION
◼Keypad and Display Description
◼Status Indicators
ICON
Description
Stability display
Negative sign
→0←
Zero setting activated
NET
Display net weight
Hold
Display hold function
Condition of battery
Power supply connected
Steady green light represents the battery is fully charged.
gram
Currently chosen weight unit
◼LED Indications
LED status
Description
Eternal on
Power adapter connected
No LED
Power adapter not connected

6
◼Keypad Description
KEY
DESCRIPTION
FUNCTION
ON/OFF Switch
Turn on and off display
Unit Switch / 
Change the weighing units to alternate units of
measurement
Hold / Target / OK
Call up hold function
Setting target weight in check-weighing mode
Tare / Backlight / ▲
Taring
Display backlight
Turning Scale On/Off
To turn the scale on, press the [ON/OFF] button. Scale will display and then enters the
active weighing mode.
To turn the scale off, press the [ON/OFF] button.
Zero Operation & Setting
When powering on the scale and if the weight on the scale is within the initial zero tolerance, the
scale will display zero automatically.
If there is nothing on the pan and the display is not zero, press [TARE] button to zero the scale.
Changing Units of Measure
In weighing mode, use [UNIT] to display the next available measuring unit. Repeat process to scroll
through all units.

7
◼Check-weighing Mode
This mode sets low and high weight limits for portion control processes.
Enter check-weighing mode
Press and hold [HOLD/TARGET] button to enter check-weighing mode.
Setting target weight values
LOWER LIMIT
SETTING
The first digit is displayed as flashing.
An annunciator appears next to the Under and the
LCD backlight is off.
Repeatedly press [TARE▲]until the desired
number appears.
Press [UNIT] to accept and move to the next
digit.
Repeat until all the digits are correct.
Press [HOLD/TARGET/OK] to confirm the setting
of lower limit and then enter to high limit setting.
HIGH LIMIT
SETTING
The first digit is displayed as flashing.
An annunciator appears next to the Over and the
LCD will light up in red.
Repeatedly press [TARE▲]until the desired
number appears.
Press [UNIT]to accept and move to the next
digit.
Repeat until all the digits are correct.
Press [HOLD/TARGET/OK] to confirm setting.
Ready for Checkweighing
If required, place an empty container on the pan and press [TARE].
Return to Weighing mode
Press and hold [HOLD/TARGET] button to return weighing mode.

8
◼Checkweighing Annunciators
The OVER, ACCEPT, and UNDER annunciators are to the right of the display as described below:
WITHIN TARGET
RANGE
The LCD lights up in green; an annunciator
appears next to “Accept”; and the scale beeps
2 short beeps.
UNDER TARGET
RANGE
The LCD backlight turns off; an annunciator
appears next to “Under”; and the scale does
not beep.
OVER TARGET
RANGE
The LCD lights up in red; an annunciator
appears next to “Over”; and the scale beeps
continuously.
If the display shows Err, this means weight
exceeds overload limit.
◼SETTINGS
Backlight Setting
Press [TARE] and hold for 2 seconds to turn ON the backlight manually.
Press [TARE] and hold for 2 seconds to turn OFF the backlight manually.
Tare Setting
Place an empty container on the scale and press [TARE]. The display will show a net value of “0” and
an annunciator appears under “NET ”.
To clear the Tare value, press [TARE] with the pan empty.
Auto off Setting
Press and hold [UNIT] for 6 seconds until the display shows . When display shows A_OFF ,
press [UNIT] to select auto turn off time or to disable this function. Press [ZERO] and press [UNIT] to
see End to confirm setting.

9
MAINTENANCE
◼Cleaning
Before cleaning, disconnect the power plug from the power outlet and remove the batteries from
the scale to completely power off the unit.
• Clean with a damp cloth and a mild soap (or similar agents if necessary) and wipe dry.
• Do not use any acids, alkalis, or strong active solvents to clean the housing or control panels.
◼Troubleshooting
SYMPTOM
POSSIBLE CAUSE
REMEDY
Scale will not turn
on
Battery discharged
Check the battery or adapter
Power cord not plugged in
properly
Check power cord connection and if
plugged in properly into the power
outlet.
Other failure
Have the scale serviced by a
KILOTECH authorized service center.
Poor accuracy
Unstable environment
Move the scale to suitable location,
refer to the manual “Selecting a
Location”.
Improper calibration
Perform calibration.
◼Service Information
If the troubleshooting section above does not resolve or describe your issue, contact your
authorized KILOTECH service agent for further assistance.