Knoll Islands 6TD00062 User manual

Islands Collection by Knoll
®Installation Instruction
Islands Collection by Knoll
®
October 2, 2020
Part Number: 6TD00062
Sheet 1
6td00062_1_hardware.ai
AG
H J K L M N
B C D E F
HARDWARE LIST
6TD40139XX
MX3 SPINE
6TD40141XX
MX4 SPINE
6TD4017901
MX3 TROUGH MOUNT
6TD4017902
MX4 TROUGH MOUNT
6TD4006601
MOUNT COVER
6TD40174
SCR,FH,1/4-20X1
6TD4010201
SCR,T-F,FL,1/4-20X5/8
6TD4008901
SCR,1/4-20X1.5,T-F
6TD40175
SCR,BHSCS,
M8-1.25X14
5134130
SCR,SM PNP#14X1
6TD4003101
FRAME CONNECTOR PLUG
5136120
SCR,
MACH FLP 1/4-20X3/4
6TD40033
GLIDE PAD
6TD40036
GLIDE
6TD40177
GLIDE M8 T SLOT NUT
6TD4002601
FRAME END CAP
P Q R S
T
Y
T2
AA AB
AC AD
U
Z
V W X
6TD40107XX
FRAME RAIL
6TD4010801
FRAME END RAIL
6TD4002901L
LH FRAME
END CONNECTOR
6TD4002901R
RH FRAME
END CONNECTOR
6TD4005601
FRAME INLINE CONNECTOR
6TD40107XX
FRAME RAIL
6TD40145XX
SPINE COVER
6TD40137
MX FOOT
5118113
SCR,FLP #10X7/8
3TA403101
WOOD BISCUIT
5340410
MEND PLATE
3TA403001
ZIP BOLT
MX Conference Tables
Reference Number: 6TD00062

Islands Collection by Knoll
®Installation Instruction
Islands Collection by Knoll
®
October 2, 2020
Part Number: 6TD00062
Sheet 2
MX Conference Tables
Reference Number: 6TD00062
STEPS:
1. Assembly of MX-Base
(Fig. 1)
1.1 Align the glide pad, item (H), to the end
of foot, item (Z), and secure into place
using 2 (B) screws.
1.2 Assemble the leveller, item (J), into the
threaded hole of the foot, item (Z).
1.3 Align and insert the tenon of foot, item
(Z), into the one of the opening of spine,
item (P) or (Q), and secure into place
using 4 (A) screws.
Start all 4 fasteners (2-3 threads) then
follow Fig. 1A for tightening sequence.
1.4 Repeat 1.1, 1.2, 1.3 for all 3 or 4 feet.
1.5 Reorient the leg assembly so that the
glide pad is facing downwards and the
open end is facing up.
1.6 Align trough mount, item (R) or (S)
with spine, item (P) or (Q), and secure
into place using 6 or 8 (C) screws.
Criss-cross tightening sequence should
be used.
1.7 Repeat all above steps to assemble all
remaining bases.
6td00062_1.ai
Fig. 1
Y
P
A
CR
Z
K
H
B
J
1
3
2
4

Islands Collection by Knoll
®Installation Instruction
Islands Collection by Knoll
®
October 2, 2020
Part Number: 6TD00062
Sheet 3
MX Conference Tables
Reference Number: 6TD00062
2. Assembly of table frame
(Fig. 2 and Fig. 3)
2.1 Orient the frame rail, item (T), as per Fig.
2A and Fig. 2C.
Note: Skip to step 2.4 for all tables less
than or equal to 120" width.
2.2 Align frame inline connector, item (X),
with the left end of the frame rail, item
(T), and secure Into place using 2 (G)
and 2 (F) screw. Detail (D) for reference.
2.3 Align the right end of second frame rail,
item (T2), with your assembly and
secure into place using 2 (G) plug and 2
(F) screw.
Repeat step 2.2 and 2.3 for the second
frame rail.
2.4 Align the LH frame end connector, item
(V), with left end of frame rail, item (T),
and secure into place using 1 (G) plug
and 1 (F) screw.
2.5 Align the RH frame end connector, item
(W), with right end of frame rail, item (T),
and secure into place using 1 (G) plug
and 1 (F) screw.
2.6 Repeat 2.4, 2.5, for second frame rail.
2.7 Align left end of first assembled rail with
provided hole of frame end rail, item (U),
and secure into place using 1 (F) screw.
2.8 Align right end of second assembled rail
with provided hole of frame end rail,
item (U), and secure into place using
1 (F) screw.
2.9 Repeat 2.7, 2.8 for attaching second
frame end rail, item (U).
2.10 Align and press in all 4 frame end
caps, item (M), into each end of
frame end rails, item (U).
6td00062_2.ai
RAILS ASSEMBLY MATRIX - TABLES WIDER THAN 120"
TABLE
WIDTH
T T2
FRAME RAIL 1 QTY FRAME RAIL 2 QTY
132" 6TD4010703 2 6TD4010709 2
144" 6TD4010705 2 6TD4010709 2
156" 6TD4010708 2 6TD4010709 2
180" 6TD4010708 2 6TD4010702 2
216" 6TD4010710 2 6TD4010708 2
Fig. 3
Fig. 2
T
V
M
U
F
W
G
F
W
X
F
G
T2
T

Islands Collection by Knoll
®Installation Instruction
Islands Collection by Knoll
®
October 2, 2020
Part Number: 6TD00062
Sheet 4
MX Conference Tables
Reference Number: 6TD00062
3. Assembly / joining individual
worksurfaces together
(Fig. 4 and Fig. 5)
Note: Step 3 is only for tables wider
than 120".
3.1 Ray worksurfaces upside down on a
soft non scratching surface, rectilinear
worksurfaces shown for example.
3.2 Insert 4 wood biscuits (AB) into available
slots on one of worksurface
(see Fig. 4).
3.3 Align other worksurface and
push them together ensuring the
wood biscuits are aligning.
3.4 Insert 4 zip bolts, item (AD), into
available slots, as per Fig. 5, and
tighten using hex key. Make sure top of
worksurface should be flush aligned.
3.5 Center and align 2 mend plates, item
(AC), into available routed areas, attach
each plate to the worksurface using 8
(AA) screws.
6td00062_3.ai
Fig. 5
Fig. 4
AD
AC
AA
AB

Islands Collection by Knoll
®Installation Instruction
Islands Collection by Knoll
®
October 2, 2020
Part Number: 6TD00062
Sheet 5
MX Conference Tables
Reference Number: 6TD00062
6td00062_4.ai
6td00062_5.ai
"X" DIMENSION FROM EDGE OF TROUGH TO END OF RAIL FRAME (FIG. 8)
TOP SHAPE
DEPTH/WIDTH 96 108 120 132 144 156 180 216
TROUGH WIDTH 68 80 92 104 116 128 152 188
RT -
RACETRACK
48 55558555
54 58888888
60 - 11 11 11 11 8 11 11
ALL OTHER
TOP SHAPES
48 5 8 8 11 11 8 11 11
54 5 8 8 11 11 8 11 11
60 - 8 8 11 11 8 11 11
X X
X
X
Fig. 7
Fig. 8
Fig. 6
L
D
E
4. Installation of assembled table
frame with worksurface
(Fig. 6)
4.1 Lay worksurface upside down on a soft
non scratching surface, rectilinear
worksurface shown for example.
4.2 Center and align holes of assembled
table frame over provided pilot holes
and attach using (E) screw.
Screw (E) quantity will vary depending
on frame rail (T) size. Use all provided
pilot holes.
5. Installation of base with table
frame
(Fig. 7 and Fig. 8)
5.1 Orient the assembled top as per Fig. 5.
5.2 Insert 8 T slot nuts, item (L), into frame
rail, item (T). As per Fig. 7.
5.3 Orient and align assembled base with t
slot nuts and secure into place using 8
(D) screws.
Before tightening screws, maintain
distance (X) as per given chart. Fig. 8
5.4 Repeat 5.2 and 5.3 for second/third
base.

Islands Collection by Knoll
®Installation Instruction
Islands Collection by Knoll
®
October 2, 2020
Part Number: 6TD00062
Sheet 6
MX Conference Tables
Reference Number: 6TD00062
6td00062_6.ai
Fig. 10
Fig. 9
N
Complete assembled table
6. Installation of mount cover
(Fig. 9 and Fig. 10)
6.1 Orient the mount cover, item (N), as per
Fig. 9.
6.2 Slide and center mount cover, item (N),
into space above trough mount.
6.3 Slide cover back and forth slightly to
engage tabs with trough mount.
6.4 Repeat 6.1, 6.2, 6.3 to install second/
third mount cover.