Knoll Tone Electric User manual

1
07.17
ASSEMBLYINSTRUCTIONS

Note that these instrucons show generic parts. Parts included in individual tables may differ in appearance and funconality
but the assembly principle is the same.
Tone Electric and Extended Electric
Complete productwithout work surface
Complete product with work surface
120⁰
90⁰
90⁰
120⁰
Housing
Sidebar
Crossbar
Column
Foot
Cauon: Noimpactdriversorotherhigh‐torqueequipmentaretobeused!

2
07.17
ASSEMBLYINSTRUCTIONS

(Fig. 1) Feet
(Fig. 2) Crossbars
Alternave foot types.

On‐Foot/OnC(for2‐stagecolumns)

On‐Foot/OffC(for2‐stagecolumns)

In‐Foot/OnC(for3‐stagecolumns)

In‐Foot/OffC(for3‐stagecolumns)




Do not use the two middle
holes of the crossbars.
Adjustable crossbar
Fixed crossbar
KR68003496
ScrewSocketRoundUNC5/16‐18x5/8”Zn
MaximumTorquefrom3to5lbf·.
KR68003490
ScrewSocketCSKUNC5/16‐18x1"Zn
LoosenScrewstoadjustcrossbarlength

3
07.17
ASSEMBLYINSTRUCTIONS

(Fig. 3) Sidebars
(Fig. 4) Bumpers
Right Hand / LeHand sidebars for C‐leg
Part numbers: KR3ae4014L ‐Le
KR3ae4014R ‐Right
Symmetric Sidebar for T‐leg
Part number: KR3ae4015
KR68003468
Bumper1/2"x1/2"x1/4"Transparent
KR68003467
BumperØ1/2"x1/8"
Transparent
Placethinbumpersontube
nexttoScrewholeand
nexttotubeedge
Placethickbumpers
onC‐channelnextto
Screwhole
KR79100036
ScrewPhilipsUndercutFlatHead1/4‐20x5/8”Zn

4
07.17
ASSEMBLYINSTRUCTIONS

(Fig. 5) 3‐Column90⁰AdjustableCrossbars
(Fig. 6) 3‐Column90⁰FixedCrossbars
Adjustable crossbars for 3‐column 90⁰table.
3 regular adjustable crossbars
1 special adjustable crossbar 
No addional assembly kit
Fixed crossbars for 3‐column 90⁰table.
3 regular fixed crossbars
1 regular fixed crossbar, 6” shorter than
the other three crossbars.
1 addional assembly kit
KR68003491
ScrewSocketCSK
UNC5/16‐18x1‐1/2"Zn
Alternavefoot
Special
telescopiccrossbar
Regularfixedcrossbar
Regularfixedcrossbar
Regularfixedcrossbar6"
shorterthantheother
threecrossbars
Alternavefoot
KR68003491
ScrewSocketCSK
UNC5/16‐18x1‐1/2"Zn
KR68004127
AssemblyKitPR2590⁰Angle


5
07.17
ASSEMBLYINSTRUCTIONS

(Fig. 7) 3‐Column120⁰AdjustableCrossbars
(Fig. 8) 3‐Column120⁰FixedCrossbars
Adjustable crossbars for 3‐column
120⁰table.
4 regular adjustable crossbars
2 Brackets
KR3AE4121 Bracket Outer
KR3AE4120 Bracket Inner
Fixed crossbars for 3‐column 120⁰table.
4 regular fixed crossbars
2 Brackets
KR3AE4121 Bracket 120⁰Outer
KR3AE4120 Bracket 120⁰Inner
KR68005205
HexNutUNC5/16‐18Zn
KR68003490
ScrewSocketCSK
UNC5/16‐18x1"Zn
KR68003490
ScrewSocketCSK
UNC5/16‐18x1"Zn
KR68005205
HexNutUNC5/16‐18Zn

6
07.17
ASSEMBLYINSTRUCTIONS

(Fig. 9) Electrical 2‐Column KR3ae4025‐ASMLightHandset
KR3ae4026‐HandsetwDisplay
KR3ae4051
HolderforPowerSupply

Hooks over crossbar or screws into work
surface.
(Fig.10) Electrical 3‐Column 90⁰
KR68002262
CableUSA2‐polIECC7DIN57625
KR68003761
PowerSupplyD0435V/2,12AACinput100‐240V,50‐60Hz
KR68002414/KR68003122
KR68002583/KR68002489
CableLinBusiDrive800/1200/1600/2000
KR3ae4025
ASMLightHandsetwScrews
KR68002414/KR68003122
KR68002583/KR68002489
CableLinBusiDrive800/1200/1600/2000
KR3ae4025
ASMLightHandsetwScrews
KR68003761
PowerSupplyD0435V/2,12AACinput100‐240V,50‐60Hz
KR68002262
CableUSA2‐polIECC7DIN57625
*KR79100378/KR79100379
P‐clipsmustbeinstalledtosecureanycables
hangingdownmorethan1.5inchesfromthe
boomoftheworksurface
*UseP‐ClipKR79100378
*UseP‐ClipKR79100379

7
07.17
ASSEMBLYINSTRUCTIONS

(Fig. 11) Electrical 3‐Column 120⁰
Warningleafletandusermanualshouldbeleon
thetableaercompletedinstallaon.
WarningLeafletToneElectricUserManualToneElectric
KR68002414/KR68003122
KR68002583/KR68002489
CableLinBusiDrive800/1200/1600/2000
KR3ae4025
ASMLightHandsetwScrews
KR68003761
PowerSupplyD0435V/2,12AACinput100‐240V,50‐60Hz
KR68002262
CableUSA2‐polIECC7DIN57625


KR79100380
P‐clipsmustbeinstalledtosecureany
cableshangingdownmorethan1.5inches
fromtheboomoftheworksurface

8
07.17
ASSEMBLYINSTRUCTIONS

Fig. 1 FEET
Assemblethefeetonthecolumns.
Tightenscrewsfirmly.MaximumTorquefrom3to5lbf·.
IMPORTANT:
Make sure the correct screws are used. Using too long screws may destroy internal parts in the column.
Fig. 2 CROSSBARS
Aachthecrossbarsonthelongsideofthehouses.Tightenscrewsfirmly.
IMPORTANT:
Do not use the two middle holes of the crossbars.
Do not insert any object in the two middle holes as this can damage electronic components.
Loosenthebuonheadscrewsonthecrossbarsandadjusttheframetodesiredwidth.
Fastenthescrewsonthecrossbars.
Fig. 3 SIDEBARS
Fastensidebarsinthreadedholesontopofcrossbarswithundercutflatheadscrews.
Twotypesofsidebarsexist,symmetricalforT‐legtablesandright/le‐handedforC‐legtables.
Fig. 4 BUMPERS
Adhesiverubberbumperscomeintwotypes;thickandthin.Thethickbumpersareonly usedontheadjustable‐widthcrossbars,
andareplacedontopoftheC‐channelinthecenter.Donotusethickbumpersonfixed‐widthcrossbars.Thethinbumpersare
placedonfixed‐widthcrossbarsandshouldbespacedevenlybetweenthesidebarsinordertopreventtheworksurfacefrom
bowing.Theworksurfacewillrestuponthebumpersonthecrossbars,anddirectlyuponthesidebars(withoutbumpers).
WORK SURFACE
Twosizesofwoodscrewsfortheworksurfaceareincludedintheassemblykit.
KR68006557ScrewPhilPanFT‐WP1710x1”Zn
KR68006558ScrewPhilTrussFT‐WP1710x2‐1/2”Zn
Theshorterscrewsgothroughthesidebars.
Thelongerscrewsgothroughthecrossbars.
IMPORTANT:
These wood screws require a minimum of 1” thick work surface.
Fig. 5 3‐COLUMN 90⁰TABLE, ADJUSTABLE CROSSBARS
3regularadjustablecrossbarsand1specialadjustablecrossbarwithanangledC‐channelareused.
Fig. 6 3‐COLUMN 90⁰TABLE, FIXED CROSSBARS
3regularfixedcrossbarstogetherwith1regularfixedcrossbar6”shorterthantheotherthreeareused.
Theassemblyprocedureisthesameasfora2‐columntablewiththeexceponthattheangledC‐channelmountstothemiddle
housewithoneextra‐longscrew1‐3/8”.
Analternavefoot,shapedasaspacer,maybeusedonthemiddlecolumn.
ASSEMBLY PROCEDURE

9
07.17
ASSEMBLYINSTRUCTIONS

Fig. 7‐83‐COLUMN 120⁰TABLE
4regularadjustableorfixedcrossbarsareusedtogetherwithtwo120⁰bracketsthataachtothemiddlecolumn.
Theassemblyprocedureisthesameasfora2‐columntable.The120⁰bracketsareaachedwithboltsandnuts.
Fig. 9 ‐11 ELECTRONICS
Thehandsetismountedatthefrontedgeoftheworksurface,screwedtotheundersidewithscrewssuppliedwiththeunit.
Connectcablesandpowersupplyaccordingtofig.9‐11

10
07.17
ASSEMBLYINSTRUCTIONS

Troubleshoong guide for Tone Electric and Extended Electric

Someoftheproposedaconsinthisguideshouldonlybeperformedbyaservicetechnician.
Endusersshouldnotaemptreplacingparts.
WARNING:DoNOTsitonbasewhileassemblinginprogress.




1. Table not running at all
1.1.1.IsthegreenLEDonthepowersupplylighton?
‐Ifnot,checkmainpowerandcableconnecons.
1.1.2.IfthegreenLEDLightissllnoton:
‐Replacethepowersupply.
1.2.LEDlightisonbutgoesoutwhentryingtooperatethetable:
‐Tryswitchingpowersuppliesbetweentables.Ifthesecondpowersupplyoperatescorrectly,replacetheoriginalpowersupply.
1.2.1.Iftheproblempersists:
‐Replacethecolumn.

1.3.Ifthelightonthepowersupplyislitallthemeandsllnotfunconing:
1.3.1.Ifthetableisinthelowestposion:
‐Pressthe"down"buononthehandsetfor4secondstoensurethatthetableisn’tinhomingmode.
1.3.2.Thetablemightbeoverheatedifthetablehasbeenrunningforaperiodof1minuteandthenhascometoahalt.Wait9
minutestoletthetablecooldownandtryagain.*)
 Ifitslldoesnotworkaer5min.:
‐Trydisconnecngpowerforabout20sandreconnect.
 Ifthereissllnofuncon:
‐Replacehandsetandcheckallconnectedcables.
 Ifthereissllnofuncon:
‐Replacecolumn.

2. Table running slow
2.1.Slowspeedbothupanddown:
‐Ifpossible,measurepowerconsumpononprimaryside.
2.1.1.Ifpowerconsumponisabove250W:
‐Replacethecolumn.
2.1.2.Ifbelow250W:
‐Replacepowersupply.

2.2.Slowspeedonlywhiledrivingup:
‐Removeweightfromtabletop.
Homing
WARNING:DoNOTsitonthetabletoapplybodyweightforperformingthehomingprocess.
Ifatablehasbeenreconfigured,oracomponent(i.e.cable,motororelectronic)hasbeenrecon‐
nectedorreplacedduringoraertheassembly,ahomingcyclemustbeperformed.Ahomingcycle
(somemesreferredtoasatablereset)shouldbeperformedwithanevenweight(!)ofapprox.
 100lbs.appliedonthetable.
Iniate a new homing cycle by:
1.Simultaneouslypressingtheupanddownbuonsforaminimumof8seconds.
2.Pressandholdthedownbuonandthetablewillslowlymovethelowestpointpossible.
3.Thetableisreadyfornormaluse.

11
07.17
ASSEMBLYINSTRUCTIONS

3. Table moving in one direcon only
3.1.Onlyrunningdowninslowspeed:
‐Thetableisinhomingmode.Toallowthetabletocompletethehomingcycle,driveallthewaydowntolowestposionto
completethehomingcycle.

3.2.Onlyabletodriveuporonlydown,butinnormalspeed:
‐Iniateanewhomingcyclebyholdingtheupanddownbuonsonthehandcontrolpressedfor8seconds.Drivethetableallthe
waydowntolowestposiontocompletethehomingcycle.
3.2.1.Sllnofuncon:
‐Replacehandcontrol.
3.2.2.Sllnofuncon:
‐Replacethecolumn.

4. Table only running a short while and then stopping
4.1.Thetablestopsandbackoff:
‐Thetablehasdetectedacollision.Checkforsomethingblockingthemovement,cables,furnitureorotherobjects.
4.1.1.Ifnothingisblockingthemovementofthetableandthesymptompersists:
‐Replacethecolumn.

4.2.Onlyrunfor2seconds:
‐Tablemightbeoverloaded,removeweightfromtabletop
4.2.1.GreenlightonpowersupplyOK?
‐Ifnot,replacepowersupply.
4.2.2.Sllnofuncon:
‐Replacethecolumn.

4.3.Onlyrunningfor20secondsormore:
‐Tablemightbeoverheang,wait9minutesandtryagain.

5. Table not moving in sync
5.1.Onlyonemotormoving:
‐Disconnectfrompower,thenreconnectallcables.

5.2.Onemotorrunninguncontrolledandothermotorjustrunning2inchesupordown:
‐Replacethecolumn.

5.3.Tablemovingupanddownnormallybuttabletopnotparalleltofloor:
‐Iniateanewhomingcyclebyholdingtheupanddownbuonspressedatthesamemefor8seconds.Drivethetableall
thewaydowntolowestposiontocompletethehomingcycle.

6. Table not able to reach top or boom posion
6.1.Tablestopsaboveboomposion/notreachingboomposion:
‐Iniateanewhomingcyclebyholdingtheupanddownbuonspressedatthesamemefor8seconds.Drivethetableall
thewaydowntolowestposiontocompletethehomingcycle.
6.1.1.Failuretoreachlowestposionduringhomingcycle:
‐Replacethecolumn.

6.2.Tablenotreachingtopposion:
‐Iniateanewhomingcyclebyholdingtheupanddownbuonspressedatthesamemefor8seconds.Drivethetableall
thewaydowntolowestposiontocompletethehomingcycle.
6.2.1.Sllnotreachingtopposion:
‐Replacethecolumn.

*)Themotordutycycleisrated10%atanominalloadof176lbs.E.g.ifthemotorrunsa1minutecycle,allow9minutesforacomplete
cooloff.Ifthemotorisengagedduringthecooloffperiodthedutycyclewillbereducedunlthefullcooloffperiodisreached.
68004686‐H©ROL|Ergo

12
07.17
ASSEMBLYINSTRUCTIONS

REVISION
DO NOT INCLUDE THIS PAGE IN PRINTOUTS
UpdatedocumentIDandrevisiononpreviouspage






RevisionDateChangeRevisedby
RevA2014‐03‐20NewdocumentAB
RevB2014‐04‐27Page2‐1/4”screwchangedto5/16”    AB
RevC2014‐05‐07ChangesmadeaccordingtoKnollrequest+Homingadded AB/PERLOH
RevD2014‐09‐26Changesmadebyaddingtroubleguide.TONSVE
RevE2014‐10‐01Newnameprocuctandblackandwhitetext,minorchanges  PERLOH
RevF2015‐03‐03Fig.3,79100036was68003465JONLAR
RevG 2016‐04‐26WoodscrewsFig.4changedLINPHA
 RevisedwoodscrewsinFig.4,Page8
 RevisedscrewtypesinFig.5,6,7&8
 RewordedbumperinstruconsinFig.4,Page8
 Newbracketouter&inneronPages1,5&7
 AddedP‐ClipsinFig.9,10&11onpages6&7
 Addedwarningsonpage10
 UpdatedhandsetdrawingsonPage6,updateddateinheader
RevH 2017‐07‐17AddedCauonNoteinpage1LINPHA
 AddedMaximumTorquefrom3to5lbf·onpage2&8

Document ID:
Revision:
Created By:
Creaon date:
Revision date:
68004686
H
AB
2014‐04‐22
2017‐07‐17