Knoll Pixel KTXE6036G User manual

PIXEL™ Installation Instructions
T-Leg Electric Height Adjustable Tables
Glides only
Unboxing
You should have received your top plus two boxes per table.
Box 1 includes:
T-Leg assemblies, feet castings, electrical controller box and
screws, control switch with cable and screws, leg extension
cables, main power cable, hardware in a red plastic bag, and
installation instructions.
Box 2 includes:
T-Leg rail kit
Hardware
28 Pan head sheet metal #10 x 1.00 screws
12 Socket button head M6 x 12mm screws
2 Pan head sheet metal #10 x 2.00 screws
8 Socket head cap M6 x 55mm screws
2 Vertical wire management clips
(clear plastic)
4 Horizontal wire management clips
with wood screws
Tools needed
Allen wrenches
Torque wrench
Phillips screwdriver
Related tables:
KTXE6036G
KTXE7236G
Fig. 1
Please pay close attention to torque requirements.
Step 1.
Lay the inverted table top on the floor.
Step 2.
Align the two “C” section rail (A) holes with the top
pilot holes. Attach the rails to the top using pan
head sheet metal #10 x 1.00 screws, 6 screws
per rail, torque: 20 in/lb
Parts list
1 Table top
2 T-Leg assemblies
2 Feet castings
1 T-Leg rail kit
1 Electrical controller box
and screws
1 Control switch with cable
and screws
2 Leg extension cables
1 Main power cable
A
4AU6009 - Oct 2015
Page 1 of 6

PIXEL™ Installation Instructions
T-Leg Electric Height Adjustable Tables
Step 3.
Align the two end bracket (B) holes with the top pilot holes.
Attach the brackets to the top using pan head sheet metal
#10 x 1.00 screws, 7 screws per rail, torque: 20 in/lb
Step 4.
Align the two ‘L’ section rails (C) with the ‘C’ section rails and
slide into the notched holes so that the end of the rails slides
into the end bracket.
Fig. 2
Fig. 3
B
B
C
C
4AU6009 - Oct 2015
Page 2 of 6

PIXEL™ Installation Instructions
T-Leg Electric Height Adjustable Tables
Step 6.
Insert the 3 staged motorized leg assemblies (G) into the
rail frame. Attach using socket button head M6 x 12mm
screws (H), 6 per leg, torque: 20 in/lb.
Fig. 5
G
G
H
H
Step 5.
Attach feet castings (D) to T-Leg 3 stage assemblies (E)
using socket head cap M6 x 55mm screws (F), 4 per leg,
torque: 20 in/lb.
H
H
H
H
Fig. 4
F
E
D
4AU6009 - Oct 2015
Page 3 of 6

PIXEL™ Installation Instructions
T-Leg Electric Height Adjustable Tables
Step 7.
Attach the controller box (I) in the
desired position between the rails
and legs motors using two pan head
sheet metal #10 x 2.00 screws (J).
Step 8.
Attach the control switch (K) on the
desired side of the table top using
two pan head sheet metal #10 x
1.00 screws (L).
Step 9.
Connect all cables: two motor ca-
bles between controller box and leg
motors (M), (controller box features
cable passages); one switch cable
(N) between the switch and control-
ler box; and the main power cable
(O) that connects to the controller
box and a wall outlet.
Step 10.
Turn the assembled table into the
upright position.
Note: Use horizontal wire manage-
ment clips to secure wires under
table.
Fig. 6
Fig. 7
L
K
I
M
M
N
N
O
J
4AU6009 - Oct 2015
Page 4 of 6

PIXEL™ Installation Instructions
T-Leg Electric Height Adjustable Tables - Operating Instructions
Fig. 9
A B C
Fig. 8
4AU6009 - Oct 2015
Page 5 of 6
Parallel drive
The arrow buttons (A).
Hold down the button to activate the parallel drive.
Memory drive
Small buttons with dots (B).
Press one of the memory buttons and the system will
start driving to the pre-programmed memory position.
Keep the button pressed until the position is reached.
Store memory
S button (C).
Press the button and within two seconds press one of
the small buttons with dots (B), and the current position
will be stored at this button.
Table Height
In standing position, table height should be just below
the elbow.

PIXEL™ Installation Instructions
T-Leg Electric Height Adjustable Tables - Troubleshooting
4AU6009 - Oct 2015
Page 6 of 6
1. The desk does not drive at all
Check: Is the main power connected to the control box?
Try/Solution: Try to connect a lamp or similar to the main
power supply to check that the supply voltage is OK.
Check: Are all plugs mounted correctly in the control box
and to the leg?
Try/Solution: Check all connections.
Check: Are there any visible damages on cables, controls,
the control box or legs?
Try/Solution: Contact Knoll Customer Service.
Check: Is something blocking the movement: cables,
furniture or other objects?
Try/Solution: Remove items that are blocking the table.
3. The desk can only drive downward (Error code E01)
The desk must be initialized.
How to initialize:
Press the down button and drive to the lowest position.
Hold the button until the desk stops completely.
Reactivate the down button and hold until the desk stops
completely.
Now the desk can drive up.
2. The desk will not drive fully upwards. Always stops in
the same position.
The system has set a new upwards stop position. To erase
this position, the desk must be initialized again. See #3.