Kogan KAMN32F7SA User manual

32” FULL HD IPS 75HZ FREESYNC
MONITOR
1920 x 1080
KAMN32F7SA

Ensure to read all instructions and warnings in this user guide prior to assembly and use.
Retain this user guide for future reference.
•Ensure the monitor is unplugged before cleaning.
•This monitor is designed with ventilation holes on the back of the casing. Do not cover
or block them.
•Do not insert any object or spray anything into the vents.
•Do not place the monitor near heaters, stoves, fireplaces, or other heat sources.
•Do not place the monitor in rooms lacking adequate ventilation.
•Do not position the monitor on unstable surfaces or unsafe locations. If the monitor
falls, it may be damaged and injure people around its vicinity.
•Unplug the monitor if it will not be used for an extended period.
•Do not place heavy objects on the monitor, its power cord, or any connected cable.
•Do not open the back panel of the monitor as it contains a high-voltage current even
when not plugged in.
The terms HDMI and HDMI High-Definition Multimedia
Interface and the HDMI Logos are trademarks or registered
trademarks of HDMI Licensing Administrator, Inc. in the
United States and other countries.
SAFETY & WARNINGS

A Monitor (x1)
B Stand connector (x1)
C Stand base (x1)
D10mm M4 stand base screw (x5)
E10mm M4 VESA
screw (x4)
FCover (x1)
GHDMI cable (x1)
HPower cable (x1)
IUser guide (x1)
COMPONENTS

Front view
1 Menu button Press to display the OSD menu or enter sub-menus.
2 Down button Press to move down in the menu.
3 Up button Press to move up in the menu.
4 Exit button Press to exit.
5 Power button Press to turn the monitor ON/OFF.
OVERVIEW

Back view
6 Audio output port
7 VGA port
8 HDMI port
9 Power port

1. Open the packaging and remove the stand connector (B) and stand base (C). Using
a Phillips head screwdriver (not supplied), secure the stand connector (B) to the stand
base (C) with two 10mm M4 stand base screws (D).
2.Remove the upper foam and reveal the lower part of the monitor (A). Fix the monitor
(A) to the stand connector (B) with three 10mm M4 stand base screws (D) in the
marked grey holes as illustrated.
3.Place the cover (F) over the stand connector (B).
STAND ASSEMBLY
B
Attention:
The monitor is fragile. Keep the foam underneath the monitor while
assembling the stand.
D
C
D
F
A
B

1. Open the packaging and take out the monitor (A) with the foam attached. Gently
place it on a desktop or table.
2.Remove the stand connector (B), stand base (C), and foam covering the back of the
monitor (A). Press the release button to remove the stand plate.
If the monitor was already attached to the stand, remove the stand.
3.Mount the monitor (A) as desired with the steps provided with your VESA mount.
Stand plate
Mount (not
included)
VESA MOUNT
Notes:
•The mounting hole distance for this monitor is 75 x 75mm.
•VESA mount and mounting accessories are not included.
B
C
A
Release
button

Power cable
Connect one end of the power cable into the power
port on the monitor. Connect the other end into a
power socket.
Earphones (audio out)
Earphones and other audio devices (not included) can
be connected to the audio output port on the monitor.
The monitor may need to be set as the PC’s default
sound output device.
HDMI
Connect the HDMI cable into your input device’s
display output and the monitor’s HDMI port.
VGA
Connect a VGA cable (not included) into your input
device’s display output and the monitor’s VGA port.
Power cable
Earphones
(Not included)
VGA cable
(not included)
VGA OUTPUT
(PC)
CONNECTIVITY
HDMI cable

1. Connect the monitor to the input device via HDMI or VGA.
2.Connect one end of the power cable to the monitor, then connect the other end
directly to a power socket. Turn on the power socket.
3.Press the power button to turn the monitor on.
4.When finished use, press the power button again to turn it off.
FreeSync
•To use this feature, ensure your hardware has FreeSync capabilities and the graphics
drivers are fully up to date.
•After connecting, you may receive a prompt to enable the feature on your computer. If
you do not receive the prompt, you may need to enable the function in your graphics
card menu.
•See your graphics card manufacturer’s documentation for instructions on how to turn
on and/or enable FreeSync.
On-screen display (OSD) menu
The OSD menu may be used to adjust the monitor’s settings.
Note:
When using the monitor for the first time, the monitor will configure to optimal settings
automatically.
OPERATION