Kohler Pillows K-7943 User manual

Installation Guide
Pillows™
Accessories
K-7943, K-7958, K-7959,
K-7960, K-7961, K-7962,
K-7963, K-7964
Mproduct numbers are for Mexico (i.e. K-12345M)
Los números de productos seguidos de
Mcorresponden a México (Ej.
K-12345M)
Français, page “Français-1”
Español, página “Español-1”
1020815-2-A

Tools and Materials
Thank You For Choosing Kohler Company
We appreciate your commitment to Kohler quality. Please take a few
minutes to review this manual before you start installation. If you
encounter any installation or performance problems, please don’t
hesitate to contact us. Our phone numbers and web site are listed on
the back cover. Thanks again for choosing Kohler Company.
Before You Begin
DANGER: Risk of personal injury. These products are not
designed or intended for use as a grab bar or support bar. Do
not install any of these products in any area where they are
likely to be used inadvertently as a grab bar or support bar.
These products should be located and mounted to a wall stud.
While it is possible to mount them to any surface, a stud mounted
product will yield the best results.
Use a level to ensure that the center lines for the wall plates are
vertical where applicable and the post center lines are horizontal
where applicable.
Kohler Co. reserves the right to make revisions in the design of
products without notice, as specified in the Price Book.
Observe all local plumbing codes and building codes.
1020815-2-A 2 Kohler Co.

1. Roughing-In Information
Kohler Co. 3 1020815-2-A

2. Mark Installation Locations
Determine the desired location of the accessory.
Mark the vertical centerline. If the accessory requires more than one
bracket, the brackets should be the recommended distance apart.
Center the wall bracket(s) on the marked centerline.
Use a level to establish the horizontal location of each wall bracket if
needed.
Mark the individual mounting holes.
Remove the wall bracket(s) and drill 1/2” holes into all mounting
hole locations.
1020815-2-A 4 Kohler Co.

3. Install the Wall Anchor(s)
Hold the toggle anchor flat alongside the plastic straps and slide it
through the previously drilled hole.
With one hand, pull the looped end straight out (do not pull at an
angle) so that the toggle anchor rests flush behind the wall.
Slide the clip along the straps with your other hand until the flange
of the clip is flush with the wall.
Place your thumb between the plastic straps. Wiggle the straps
side-to-side until they snap off at the wall.
Insert the enclosed bolt through the wall plate and tighten until it is
flush with the wall.
Minimum clearance behind the wall is 1–7/8” (4.8cm).
4. Install the Wall Bracket
Insert the mounting screws through the wall bracket mounting holes
and into the slip fitting.
Thread the screws into the metal channel and tighten with a Phillips
screwdriver.
Kohler Co. 5 1020815-2-A

5. Install the Robe Hook
Position the robe hook on the wall bracket.
Place a screw on a 1/8” hex head wrench and thread through the
wall bracket from underneath into the robe hook.
Tighten the screw.
1020815-2-A 6 Kohler Co.

6. Install the Soap Dish
Position the soap dish holder on the wall bracket.
Place a screw on a 1/8” hex head wrench and thread through the
wall bracket from underneath the soap dish holder.
Repeat with the second screw.
Tighten the screws.
Place the soap dish in the holder.
7. Install the Tumbler Holder
Position the base on the wall bracket.
Place a screw on a 1/8” hex head wrench and thread through the
wall bracket from underneath into the base.
Repeat with the second screw.
Tighten the screws.
Place the tumbler holder in the base.
Place the toothbrush drawer into the carriage slot under the base.
Kohler Co. 7 1020815-2-A

8. Install the Tissue Holder
Position the tissue holder on the wall bracket.
Place a screw on a 1/8” hex head wrench and thread through the
wall bracket from underneath the base.
Repeat with the second screw.
Tighten the screws.
Attach the spindle to the holder.
9. Install the Towel Ring
Position the towel ring on the wall bracket.
Place a screw on a 1/8” hex head wrench and thread through the
wall bracket from underneath into the towel ring.
Tighten the screws.
1020815-2-A 8 Kohler Co.

10. Install the Towel Bar
Place the ends of the towel bar into the arms and use a 3/32” hex
wrench to tighten the screw.
Position the towel bar arms on the wall brackets.
Place a screw on a 1/8” hex head wrench and thread through the
wall bracket from underneath the towel bar arm. Repeat for the
second towel arm.
Tighten the screws.
Kohler Co. 9 1020815-2-A

11. Install the Glass Shelf
Position a glass shelf holder on a wall bracket.
Place a screw on a 1/8” hex head wrench and thread through the
wall bracket from underneath the glass shelf holder.
Repeat for the second glass shelf holder.
Tighten the screws.
Press a vinyl tube into the slot on each glass shelf holder.
Place the glass shelf on the vinyl tubes.
Press the plastic retaining clips into place. Insert the screws into the
bottom hole and tighten.
1020815-2-A 10 Kohler Co.