Kontron 104 User manual

V PANEL
104 / 121 / 150 / 170 / 190
User manual
Rel. 08.2005 Ver.01
0-0096-3132
The German version of this manual is not available.
Die deutsche Version ist nicht verfügbar.
StockCheck.com

V Panel 104 / 121 / 150 / 170 / 190 User Manual
2© Copyright Kontron Embedded Computers GmbH
Kontron Embedded Computers GmbH
Werner-von-Siemens-Str. 1
93426 Roding
Phone: [phone]
Fax: [phone]
e-mail: [email protected]
Internet: http://www.kontron.com
© Copyright Kontron Embedded Computers GmbH 2005. All rights are reserved
Manual History
Date Version Changes
Aug.2005 01 First edition
StockCheck.com

http://www.kontron.com 3
Werner-von-Siemens Str.1
D - 93426 Roding
Tel: [phone] - 0
Fax: [phone] - 100
COPYRIGHT
Copyright Kontron Embedded Computers
All rights are reserved
No part of this product, including the product and software may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any lan-
guage in any form by any means without the express written permission of
Kontron Embedded Computers GmbH (herinafter referred to as Kontron) ex-
cept documentation kept by the purchaser for backup purposes.
TRADEMARKS
All trademarks mentioned in this manual are registered properly of the respec-
tive owners.
CE-CONFORMITY
The following requirements, standards, specifications constitute part of the dec-
laration:
EN 55022 class A EN 55024 EN 60950
EN 61000-3-2 EN 61000-3-3 EN 61000-6-2
The validation of this declaration depends on the properly use of the product.
FCC Class A Radio Frequency
This equipment has been tested and found to comply with the limits for a Class
Adigital device, pursuant to 1/47 CFR Part 15.109 ClassAof FCC rules. Opera-
tion is subject to the following two conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference received, including interference
that may cause undesired operation.
The limits of FCC Part15 classAare designed to provide reasonable protection
against harmful interference in residential installation. This equipment gener-
ates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interfer-
StockCheck.com

V Panel 104 / 121 / 150 / 170 / 190 User Manual
4© Copyright Kontron Embedded Computers GmbH
ence to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference
by more of one or more of the following measures:
1. Reorient or relocate the receiving antenna
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
4. Consult the dealer or an experienced radio/television technican for help.
Notice1: The changes or modifications not expressly approved by the party
responsible for compliance could void the user`s authority to operate the equip-
ment.
Notice2: Shielded interface cables, if any, must be used in order to comply with
emission limits.
CAUTION !
RISK OF EXPLOSION IF BATTERY IS REPLACED
BY AN INCORRECT TYPE
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
StockCheck.com

http://www.kontron.com 5
Werner-von-Siemens Str.1
D - 93426 Roding
Tel: [phone] - 0
Fax: [phone] - 100
Table of contents
Copyright....................................................................................................3
Trademarks ................................................................................................3
CE-Conformity............................................................................................3
1. Introduction .................................................................................................6
2. Overview ....................................................................................................8
3. Hardware Installation...................................................................................9
3.1 Connect external devices ................................................................9
3.2 Connect internal devices ............................................................... 11
3.3 Internal Jumper setting ..................................................................12
3.4 LED Status indicators ....................................................................14
4 Software installation ..................................................................................15
4.1 Application software and operating system ...................................15
4.2 Hardware drivers ...........................................................................15
5. Technical Details .......................................................................................23
5.1 Mechanical ....................................................................................23
5.2 Electronical ...................................................................................23
5.3 Environment .................................................................................24
5.4 CE Directives and Standards........................................................24
5.5 Connector pinout ...........................................................................24
5.6 Options .........................................................................................31
5.7 Block diagram...............................................................................33
6. Maintenance ........................................................................................34
6.1 Customer service...........................................................................34
6.2 Cleaning ........................................................................................34
6.3 Return and repair..........................................................................34
6.4 Packaging......................................................................................35
7. Troubleshooting ...................................................................................36
7.1 FAQ ...............................................................................................36
8. Disposal...............................................................................................36
9. Appendix..............................................................................................36
StockCheck.com

V Panel 104 / 121 / 150 / 170 / 190 User Manual
6© Copyright Kontron Embedded Computers GmbH
1. INTRODUCTION
1.1. APPROPRIATE USE
The main purpose of the V Panel is the use and operation with 24VDC-power-
sources.
The surrounding area of the Panel are dry rooms.
The Panel is intended for industrial applications in machine and plant control
engineering.
The user is not entitled to change the system components or open the body
without consultation to Kontron.
1.2 ITEM CHECKLIST
Your Panel comes securely packaged in solid shipping carton(s). Upon receiv-
ing your Panel, open the carton(s) and remove the contents carefully.
The shipping carton should contain the following items:
- V Panel 10,4” 12,1” 15” 17” or 19”
- CPU Support CD (optional)
- 24V DC Power cord (optional)
- This user manual (optional)
- Software installation CD if implemented
Carefully inspect each component to ensure that nothing is missing and/or
damaged. If any of these items is missing or damaged, please contact Kontron
immediately. Preserve of of the packing material for future transportation.
1.3 IMPORTANT SAFETY INSTRUCTIONS
This section gives you detailed information about how to maintain a safe
environment while using the Panel. You can maintain its condition and perfor-
mance by following these guidelines. Please read it carefully to ensure maxi-
mum safety.
Be careful about the power supply input voltage. The Panel has specific
power requirements.
Please prevent the Panel from humidity.
Never pour any liquid on the Panel, this may cause fire or electrical shock.
Place the Panel on a reliable surface when installing.Adrop or fall may cause
damage.
StockCheck.com

http://www.kontron.com 7
Werner-von-Siemens Str.1
D - 93426 Roding
Tel: [phone] - 0
Fax: [phone] - 100
Do not leave the Panel in an unconditional environment. Storage temperature
above 70°C may damage the Panel.
The opening on the enclosure are for air convection, protect the Panel from
overheating. DO NOT COVER THE OPENINGS
If the Panel is not in use for a long time, disconnect it from mains to avoid
possible damage by transient overvoltage.
If you had to open the housing of the Panel in service cases, all single parts of
the plant must first be switched off, after which the Panel can be disconnected
fromtheplant. Secure eachpartagainstaccidentally switchedonduring service.
Following service activities on the Panel could cause failures.
• Metal objects such as screws or tools fall on or in the Panel
• Cables are removed or inserted during operation.
• Plug-in cards are removed or inserted during the Panel is
switched on.
All cautions and warnings on the Panel should be noted.
The system has to shut down and checked immediately by service staff, if one
of the following situation appears:
• The power cord or plug is damaged.
• Liquid has penetrated the Panel.
• The Panel is exposed to moisture.
• Obvious sign of breakage are visible.
• System did not work properly or you can not get it work
according to the application requirements.
StockCheck.com

V Panel 104 / 121 / 150 / 170 / 190 User Manual
8© Copyright Kontron Embedded Computers GmbH
2. OVERVIEW
The Kontron V Panel computer is a high performance system. The compact
designenablesan integrationevenunderthe condition ofvery restrictedspaces.
Our 100% industiy capable, scalable Panel meet the highest requirements
concerning shock, vibration and temperature resistance. The system also
provides a high resistance under tough EMC conditions.
Features:
- Display sizes 10,4“ 12,1“ 15” 17” and 19”
- Display type TFT active Matrix LCD with resistive touch.
- Color depth up to 32 bit
- Max. Resolution 1280x 1024
- Intel Pentium M Processor up to 1.1 Ghz
- Main memory up to 1024 MB on SDRAM
- Standard interfaces 3x USB, 2x PS/2, 1x LPT, 2x LAN, 4x RS232
- Input power of 24 VDC
- Installation of two PCI extension cards.
- Front side protection in IP65 (conform to EN 60529)
- Operating temperature up to 50°C
- Operating system Windows and Linux
- Dimension 10.4” 295mm x 348mm x 121mm
12.1” 327mm x 400mm x 121mm
15.0” 362mm x 452mm x 123mm
17.0” 390mm x 465mm x 130mm
19.0” 426mm x 516mm x 135mm
- All connectors build for industrial standards
- Shock and vibration tested
- Embedded architecture long-life electronic components
- Optional:Stainlesssteel front,front USB, PowerON switch,power LED
StockCheck.com

http://www.kontron.com 9
Werner-von-Siemens Str.1
D - 93426 Roding
Tel: [phone] - 0
Fax: [phone] - 100
3. HARDWARE INSTALLATION
Attention!
The weight of the Panel is about 7kg
Carry it on with both hands!
The Panel of this type is developed to work in a control cabinet. Thereby it must
be pointed that all the environmental conditions must be considered.
When installing the Panel take care that there is enough area for ventilations on
rear side. For details go to item housing dimensions.
If your Panel was delivered without software install a keyboard and mouse.
If operating system and software is installed, the touch is working and cali-
brated.
Look up for further settings e.g. BIOS on the ETX board manuals.
3.1 CONNECT EXTERNAL DEVICES
Toget detailedinformation about pinoutof eachconnector please lookto chapter
“technical details”.
COM 3
MOUSE
KEYBOARD
LAN 1
USB
LPT
COM 1 CRT COM 2 LAN 2
POWER
HDD
RESET POWER
POWER-ON
Fieldbus
Fig. 3-1
3.1.1 PS/2 Keyboard and Mouse
Use this connector to connect PS/2 mouse and keyboard.
3.1.2 LAN1 Port
Thisconnector provides a external interfaces10/100 BaseTon RJ45 to connect
your Panel to other devices in a network.
StockCheck.com

V Panel 104 / 121 / 150 / 170 / 190 User Manual
10 © Copyright Kontron Embedded Computers GmbH
3.1.3 USB port
This connector provides two external USB 2.0 interfaces
3.1.4 Parallel port LPT
Use this port to connect a printer or other parallel devices.
3.1.5 Serial Interface COM1, COM2, COM3
Three serial interfaces enables you to connect a external device with 9 pin
DSUB connector such as mouse or modem. COM2 is selectable as a input for
programming fielbuscontroller.
3.1.6 Fieldbus interface CAN / CANOpen / Profibus / DeviceNet
External connector of internal fieldbus controller. Interface to connect CAN,
CANOpen, Profibus/MPI or DeviceNet devices. All interfaces in master or
slave configuration available.
3.1.7 CRT Monitor
Connector and interface to VGA/CRT monitor .
3.1.8 Second LAN2 Port
This connector provides a second external interfaces 10/100/1000 BaseT on
RJ45 connector to your panel to other devices in a network.
3.1.9 Reset
Reset Switch reset the hole unit.
3.1.10 Main power IN
Use this connector to connect the power supply of 24VDC. Please note the
Power requirements (See chapter technical details).
3.1.11 Power ON button
Enables you to switch on and off the main system.
3.1.13 Front USB
Use this port behind a cover to connect USB devices direct on the panel front
StockCheck.com

http://www.kontron.com 11
Werner-von-Siemens Str.1
D - 93426 Roding
Tel: [phone] - 0
Fax: [phone] - 100
3.2 CONNECT INTERNAL DEVICES
The panel provides additional functions which could be implemented in the
system by adding cards or changing the configuration of your Panel.
ETX CPU Module
CF
Fig. 3-2
StockCheck.com

V Panel 104 / 121 / 150 / 170 / 190 User Manual
12 © Copyright Kontron Embedded Computers GmbH
Connector Interface
J3 Serial port COM3
J4 Serial port COM4
J6 Backlight interface
J12 Advanced power button interface
J13 External battery connector
J15 Internal Fieldbus interface
J16 Floppy disk drive interface
J17 Secondary IDE Compact flash
J18 Primary IDE Connector UDMA33
J21 IrDA/FIR connector
J24 PCI extension card
J25 PCMCIA
J26 Internal HDD power interface
J29 4-5 wire Tochconnector
J30 DMC touchcontroller interface (option)
J31/J32 Internal USB interfaces
J34 Speaker interface
J36 ATX Power button
3.3 INTERNAL JUMPER SETTING
To identify the jumper location please look to the board layout in Fig.3.2. All
described functions refers to the implemented baseboard.
3.3.1 Backlight supply voltage J5
Setting Backlight supply voltage
1-2 (default) 12V
2-3 5V
3.3.2 Voltage supplied to display J8
321
456
Setting Display supply voltage
1-6 (default) 3V
2-5 5V
3-4 12V
3.3.3 Address range NVSRAM Switch DIP1 SW1
ON
1
OFF
Setting SW1 DIP1 NVSRAM address
OFF CC000 – CFFFF (Hex)
ON D0000 – D7000 (Hex)
*TO ENABLE THE NVSR
A
M DIP8 ON SW1 MUST BE SET TO OFF. IF SJ
A
1000 CHIP SIS POPULATED DIP2 ON SW1 MUST BE SET TO OFF.
StockCheck.com

http://www.kontron.com 13
Werner-von-Siemens Str.1
D - 93426 Roding
Tel: [phone] - 0
Fax: [phone] - 100
3.3.4 Address range fielbus controller EC1 SW1
Setting SW1 DIP2 Base address fielbus contr. EC1
ON CA000 – CBFFF (Hex)
OFF DA000 – DB000 (Hex) and
SJA1000 fieldbuscontroller populated
3.3.5 Fieldbus Contrl. SJ1000 Interrupt (optional) SW1
Setiing SW1
DIP3 DIP4 DIP5 Interrupt request
OFF OFF OFF IRQ3
OFF OFF ON IRQ4
OFF ON OFF IRQ5
OFF ON ON IRQ7
ON OFF OFF IRQ10
ON OFF ON IRQ11
ON ON OFF No fieldbus installed
ON ON ON No interrupt
3.3.6 Fieldbus Contrl. SJ1000 IO Address (optional) SW1
Setting SW1
DIP6 DIP7 DIP8 IO-address
OFF OFF OFF IRQ3
OFF OFF ON IRQ4
OFF ON OFF IRQ5
OFF ON ON IRQ7
ON OFF OFF IRQ10
ON OFF ON IRQ11
ON ON OFF No fieldbus installed
ON ON ON No interrupt
3.3.7 Master-Slave configuration of Compact Flash SW2
ON
1
OFF
Setting SW2 DIP1 Function Compact Flash
OFF (default) Master
ON Slave
3.3.8 I/O configuration of COM2 SW2
Setting SW2 DIP2 Function Compact Flash
OFF (default) COM2
ON Input for external programming EC1
3.3.9 Function front power bottom SW2
Setting SW2 DIP3 Funktion Compact Flash
OFF Powerbutton J12 disabled
ON (default) Powerbutton J12 enabled
3.3.10 Configuration USB Port 2 SW2
Setting SW2 DIP4 Funktion Compact Flash
OFF (default) USB Port 2 enabled
ON USB Port 2 disabled
StockCheck.com

V Panel 104 / 121 / 150 / 170 / 190 User Manual
14 © Copyright Kontron Embedded Computers GmbH
3.3.11 Communication port to touchcontroller SW3
ON
1
OFF
Setting SW3 DIP1 Communication port COM
OFF COM1
ON COM4
3.3.12 Touch wire configurationr SW3
ON
1
OFF
Setting SW3 DIP2 Touchtype
OFF 5 wire
ON 4 wire
3.3.13 Output configuration USB Port 0 SW4
ON
1
OFF
Setting SW4 DIP1 USB Port 0
OFF (default) External Connector J22
ON Internal Connector J31
3.3.14 Output configuration USB Port I SW4
Setting SW4 DIP2 USB Port 1
OFF (default) External Connector J22
ON Internal Connector J31
3.4 LED STATUS INDICATORS
3.3.1 Power LED D16 bottom
Description ON green OFF
POWER POWER OK No power
3.3.2 HDD LED D16 top
Description ON red OFF
HDD activity Datatranfer from/to HDD No access
3.3.3 Fieldbus status
Status including possible fieldbus modules
Baseboard LED D18 CanOpen and
Profibus Module DeviceNet Module Indicated Status
Top Ready
(yellow) Bottom RUN
(green)
ERROR
D1 Status D2 ERROR D3
Flashing
irregular OFF OFF OFF OFF Fieldbus hardware error
Flashing
cyclic OFF OFF OFF OFF Bootstraploader active
ON Flashing
irregular OFF OFF RED No slave or fieldbus not connected
ON Flashing
cyclic OFF ON - PC applikation not redy
ON Flashing
cyclic ON OFF - Short circuite at fieldbus
ON Flashing
cyclic ON ON RED No slave or fielbus not connected
ON ON ON ON RED At least one slave is missing
ON ON
OFF ON GREEN Communication is running faultless
StockCheck.com

http://www.kontron.com 15
Werner-von-Siemens Str.1
D - 93426 Roding
Tel: [phone] - 0
Fax: [phone] - 100
4 SOFTWARE INSTALLATION
4.1 APPLICATION SOFTWARE AND OPERATING SYSTEM
The panel is designed to work with different operating systems. To install
operating system or application software follow the installation instructions of
the software.
4.2 HARDWARE DRIVERS
On preinstalled systems no drivers had to be installed by a technican or user. If
nooperating systemwas installed,you hadto installdriversfor the implemented
hardware to get full function of the panel. All the drivers are stored on the
provided Support CD. Drivers also available at the online support at
http://www.kontron.com.
If you need additional help please contact Kontron customer service.
4.2.1 Install Touch driver
Installed touch controllers
Installed Touch 10,4” 12,1” 15” 17” 19”
SS ALU SS ALU SS ALU SS ALU SS ALU
Elo touchcontroller X X X X
DMC touchcontroller X X X X X X
SS=stainless steel Front bezel , ALU= Aluminium Front bezel
Preparations of system
Before installing the driver please check the following items.
- USB Port in BIOS enabled
- USB Port driver for operating system installed.
- Device for loading the drivers is installed
- Optional: download driver from WEB
Install DMC touch driver
Installation procedure
To start driver installation please go to the folder where all the driver files are
stored. Start driver installation by double click on file “SETUP.exe” in the
respective folder. Confirm each opened window with “NEXT” when choice is
done. Please observe that during installation no error occurs.
StockCheck.com

V Panel 104 / 121 / 150 / 170 / 190 User Manual
16 © Copyright Kontron Embedded Computers GmbH
>>Start installation and set folder
>>Choose your destination folder
StockCheck.com

http://www.kontron.com 17
Werner-von-Siemens Str.1
D - 93426 Roding
Tel: [phone] - 0
Fax: [phone] - 100
>>Choose display of touch icon in
system tray
>>Select installed touch controllers
Value: 1
>>Select spread of touch on display
Value line 1:“Whole Desktop”
Value line 2:“Device1”
StockCheck.com

V Panel 104 / 121 / 150 / 170 / 190 User Manual
18 © Copyright Kontron Embedded Computers GmbH
>> Select controler type
Value: DMC TSC-10 Series USB
>> Installation
Calibration
To get the according touch function you had to calibrate the touch.
To do this go to START/Programs/DMC/ Calibrate
Do the calibration with a touch stick on the displayed arrows.
Install ELO touch driver
Installation procedure
To start driver installation please go to the folder where the driver files are
stored. Start driver installation by double click on file “SW500930.exe” in the
respective folder. Confirm each opened window with “OK” or “NEXT” when
choice is done.
Please observe that during installation no error occurs.
StockCheck.com

http://www.kontron.com 19
Werner-von-Siemens Str.1
D - 93426 Roding
Tel: [phone] - 0
Fax: [phone] - 100
>> Choose your destination
folder to extract files
>> Select touch type
“USB touchsreen “
StockCheck.com

V Panel 104 / 121 / 150 / 170 / 190 User Manual
20 © Copyright Kontron Embedded Computers GmbH
>>Confirm licence agreement
>>Start touch calibration
StockCheck.com