Kontron KTQ67/Flex User manual

If it’s embedded, it’s Kontron
KTQ67 Users Guide - Preliminary
KTD-N0829-C
KTQ67/Flex
KTQ67/ATXE

KTQ67 Users Guide
KTD-N0829-C Page 2
Document revision history.
Revision
Date
By
Comment
C Jan 2nd 2011 MLA
Processor list updated. LPT removed. Added KTQ67/ATXE
pictures and related info. Added cooling info. Added SPI
connector correction and description.
B Nov. 9th 2011 MLA
Added Power consumptions. Corrected GPIO8-12. Battery type
no. replaced. Minor updated info.
A
Sept. 8th 2011
MLA
Preliminary version. Corrections. LVDS optionally.
0
Aug 26th 2011
MLA
Preliminary version
Copyright Notice:
Copyright 2011, KONTRON Technology A/S, ALL RIGHTS RESERVED.
No part of this document may be reproduced or transmitted in any form or by any means, electronically
or mechanically, for any purpose, without the express written permission of KONTRON Technology A/S.
Trademark Acknowledgement:
Brand and product names are trademarks or registered trademarks of their respective owners.
Disclaimer:
KONTRON Technology A/S reserves the right to make changes, without notice, to any product,
including circuits and/or software described or contained in this manual in order to improve design
and/or performance.
Specifications listed in this manual are subject to change without notice. KONTRON Technology
assumes no responsibility or liability for the use of the described product(s), conveys no license or title
under any patent, copyright, or mask work rights to these products, and makes no representations or
warranties that these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified. Applications that are described in this manual are for illustration purposes only.
KONTRON Technology A/S makes no representation or warranty that such application will be suitable
for the specified use without further testing or modification.
Life Support Policy
KONTRON Technology’s PRODUCTS ARE NOT FOR USE AS CRITICAL COMPONENTS IN LIFE
SUPPORT DEVICES OR SYSTEMS WITHOUT EXPRESS WRITTEN APPROVAL OF THE GENERAL
MANAGER OF KONTRON Technology A/S.
As used herein:
Life support devices or systems are devices or systems which, (a) are intended for surgical implant into
body, or (b) support or sustain life and whose failure to perform, when properly used in accordance with
instructions for use provided in the labelling, can be reasonably expected to result in significant injury to
the user.
A critical component is any component of a life support device or system whose failure to perform can
be reasonably expected to cause the failure of the life support device or system, or to affect its safety or
effectiveness.
Document details

KTQ67 Users Guide
KTD-N0829-C Page 3
KONTRON Technology Technical Support & Services
If you have questions about installing or using your KONTRON Technology Product, check this User’s
Manual first – you will find answers to most questions here. To obtain support, please contact your local
Distributor or Field Application Engineer (FAE).
Before Contacting Support: Please be prepared to provide as much information as possible:
•CPU Board
1. Type.
2. Part Number (find PN on label)
3. Serial Number if available (find SN on label)
•Configuration
1. CPU Type, Clock speed
2. DRAM Type and Size.
3. BIOS Revision (Find the Version Info in the BIOS Setup).
4. BIOS Settings different than Default Settings (Refer to the BIOS Setup Section).
•System
1. O/S Make and Version.
2. Driver Version numbers (Graphics, Network, and Audio).
3. Attached Hardware: Harddisks, CD-rom, LCD Panels etc.
Warranty
KONTRON Technology warrants its products to be free from defects in material and workmanship
during the warranty period. If a product proves to be defective in material or workmanship during the
warranty period, KONTRON Technology will, at its sole option, repair or replace the product with a
similar product.
Replacement Product or parts may include remanufactured or refurbished parts or components.
The warranty does not cover:
1. Damage, deterioration or malfunction resulting from:
A. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product
modification, or failure to follow instructions supplied with the product.
B. Repair or attempted repair by anyone not authorized by KONTRON Technology.
C. Causes external to the product, such as electric power fluctuations or failure.
D. Normal wear and tear.
E. Any other causes which does not relate to a product defect.
2. Removal, installation, and set-up service charges.
Exclusion of damages:
KONTRON TECHNOLOGY LIABILITY IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT
OF THE PRODUCT. KONTRON TECHNOLOGY SHALL NOT BE LIABLE FOR:
1. DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN THE PRODUCT,
DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF
TIME, LOSS OF PROFITS, LOSS OF BUSINESS OPPORTUNITY, LOSS OF GOODWILL,
INTERFERENCE WITH BUSINESS RELATIONSHIPS, OR OTHER COMMERCIAL LOSS,
EVEN IF ADVISED OF THEIR POSSIBILITY OF SUCH DAMAGES.
2. ANY OTHER DAMAGES, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
3. ANY CLAIM AGAINST THE CUSTOMER BY ANY OTHER PARTY.
Document details

KTQ67 Users Guide
KTD-N0829-C Page 4
Contents
Introduction .............................................................................................7
1Installation procedure.......................................................................8
1.1 Installing the board........................................................................................................................8
1.2 Requirement according to IEC60950............................................................................................9
2System Specification......................................................................10
2.1 Component main data.................................................................................................................10
2.2 System overview.........................................................................................................................14
2.3 Processor Support Table.............................................................................................................16
2.4 System Memory support .............................................................................................................18
2.5 KTQ67 Graphics Subsystem.......................................................................................................19
2.5.1 Intel® HD Graphics 3000...........................................................................................................19
2.6 Power Consumption....................................................................................................................20
3Connector Locations......................................................................23
3.1 KTQ67/Flex – frontside ...............................................................................................................23
3.2 KTQ67/Flex - backside................................................................................................................24
3.3 KTQ67/ATXE...............................................................................................................................25
3.4 KTQ67/ATXE - backside.............................................................................................................26
4Connector Definitions.....................................................................27
5IO-Area Connectors.......................................................................28
5.1 Display connectors (IO Area)......................................................................................................28
5.1.1 Analogue VGA (VGA) ................................................................................................................28
5.1.2 DP Connectors (DP0/DP1) ........................................................................................................29
5.2 Ethernet Connectors (IO Area) ...................................................................................................30
5.3 USB Connectors (IO Area)..........................................................................................................31
5.3.1 USB Connector 0/1 (USB0/1)....................................................................................................31
5.3.2 USB Connector 2/3 (USB2/3)....................................................................................................32
5.3.3 USB Connector 4/5 (USB4/5)....................................................................................................32
5.4 Audio Connector (IO Area)..........................................................................................................33
5.5 COM1 Connector (IO Area).........................................................................................................34

KTQ67 Users Guide
KTD-N0829-C Page 5
6Internal Connectors........................................................................35
6.1 Power Connector (ATX/BTXPWR)..............................................................................................35
6.2 Fan Connectors (FAN_CPU) (J28) and (FAN_SYS) (J29).........................................................36
6.3 PS/2 Keyboard and Mouse connector (KBDMSE) (J15) ............................................................37
6.4 Display connectors (Internal).......................................................................................................38
6.4.1 LVDS Flat Panel Connector (LVDS) (J39) (optionally)..............................................................38
6.5 SATA (Serial ATA) Disk interface (J22 – J27) ............................................................................39
6.6 USB Connectors (USB)...............................................................................................................40
6.6.1 USB Connector 6/7....................................................................................................................40
6.6.2 USB Connector 8/9 (USB8/9) (J18)...........................................................................................40
6.6.3 USB Connector 10/11 (USB10/11) (J17)...................................................................................41
6.6.4 USB Connector 12/13 (USB12/13) (J16)...................................................................................41
6.7 Serial COM2 – COM4 Ports (J19, J20, J21)...............................................................................42
6.8 Audio Connectors........................................................................................................................43
6.8.1 CDROM Audio Input (CDROM) (J44)........................................................................................43
6.8.2 Line2 and Mic2...........................................................................................................................43
6.8.1 Audio Header Connector (AUDIO_HEAD) (J47).......................................................................44
6.9 Front Panel Connector (FRONTPNL) (J36)................................................................................45
6.10 Feature Connector (FEATURE) (J30).........................................................................................46
6.11 Clear CMOS Jumper (J11)..........................................................................................................48
6.12 ClrRTC (J12) ...............................................................................................................................48
6.13 SPI Recover Jumper (J41)..........................................................................................................49
6.14 SPI Connector (SPI) (J40)...........................................................................................................50
6.15 XDP-CPU (Debug Port for CPU) (J14) .......................................................................................51
6.16 XDP-PCH (Debug Port for Chipset) (J13)...................................................................................52
7Slot Connectors (PCIe, mSATA, miniPCIe, PCI)............................53
7.1 PCIe Connectors.........................................................................................................................53
7.1.1 PCI-Express x16 Connector (PCIe x16)....................................................................................53
7.1.2 mSATA (J43)..............................................................................................................................55
7.1.3 miniPCI-Express mPCIe (J42)...................................................................................................56
7.1.4 PCI-Express x4 Connector (PCIe x4) (J33)...............................................................................57
7.2 PCI Slot Connectors...................................................................................................................58
7.2.1 Signal Description – PCI Slot Connector...................................................................................59
7.2.2 KTQ67 PCI IRQ & INT routing...................................................................................................60
8On-board - & mating connector types.............................................61

KTQ67 Users Guide
KTD-N0829-C Page 6
9System Resources.........................................................................62
9.1 Memory Map ...............................................................................................................................62
9.2 PCI Devices.................................................................................................................................63
9.3 Interrupt Usage............................................................................................................................64
9.4 IO Map.........................................................................................................................................65
10 BIOS..............................................................................................67
11 AMI BIOS Beep Codes...................................................................68
12 OS Setup .......................................................................................69

KTQ67 Users Guide
KTD-N0829-C Page 7
Introduction
This manual describes the KTQ67/Flex and KTQ67/ATXE boards made by KONTRON Technology A/S.
The boards will also be denoted KTQ67 family if no differentiation is required.
The KTQ67 boards, all based on the Q67 chipset, support 2nd generation Intel® i7 -, i5 -, i3 2Core and
4Core processor and the Celeron B810 2Core, see “Processor Support Table for more specific details.
The KTQ67 family consist on members having different form factors, and the same functionality except
for the functions listed in the table below.
KTQ67 variants
Format
PCI
LPT
LVDS
KTQ67/Flex Flex 2
-
-
KTQ67/ATXE ATX 5
-
-
Note. LPT and LVDS is optionally for future variants. LPT and LVDS connectors can be found on some
EFT samples, but is unsupported.
Use of this Users Guide implies a basic knowledge of PC-AT hard- and software. This manual is
focused on describing the KTQ67 board’s special features and is not intended to be a standard PC-AT
textbook.
New users are recommended to study the short installation procedure stated in the following chapter
before switching-on the power.
All configuration and setup of the CPU board is either done automatically or manually by the user via
the CMOS setup menus. Only exception is the Clear CMOS jumper.
Introduction

KTQ67 Users Guide
KTD-N0829-C Page 8
Warning: Turn off PSU (Power Supply Unit) completely (no mains power connected to the
PSU) or leave the Power Connectors unconnected while configuring the board. Otherwise
components (DRAM, LAN cards etc.) might get damaged. Make sure PSU has 3.3V monitoring
watchdog (standard ATX PSU feature), running the board without 3.3V will damage the board
within minutes.
!
!
Warning: When mounting the board to chassis etc. please notice that the board contains
components on both sides of the PCB which can easily be damaged if board is handled
without reasonable care. A damaged component can result in malfunction or no function at all.
1 Installation procedure
1.1 Installing the board
To get the board running, follow these steps. If the board shipped from KONTRON has already
components like DRAM, CPU and cooler mounted, then relevant steps below, can be skipped.
1. Turn off the PSU (Power Supply Unit)
2. Insert the DRAM(s) (UDIMM 240pin)
Be careful to push it in the slot(s) before locking the tabs. For a list of approved DRAM contact your
Distributor or FAE. See also chapter “System Memory Support”.
3. Install the processor
The CPU is keyed and will only mount in the CPU socket in one way. Use finger to open/ close the
CPU socket. Refer to supported processor overview for details.
4. Cooler Installation
Use heat paste or adhesive pads between CPU and cooler and connect the Fan electrically to the
FAN_CPU connector.
5. Connecting Interfaces
Insert all external cables for hard disk, keyboard etc. A monitor must be connected in order to be
able change CMOS settings.
6. Connect and turn on PSU
Connect PSU to the board by the ATX/BTXPWR and the 4-pin ATX+12V connectors.
7. Power Button
The PWRBTN_IN must be toggled to start the Power supply; this is done by shorting pins 16
(PWRBTN_IN) and pin 18 (GND) on the FRONTPNL connector (see Connector description). A
“normally open” switch can be connected via the FRONTPNL connector.
8. BIOS Setup
Enter the BIOS setup by pressing the <Del> key during boot up.
Enter Exit Menu and Load Optimal Defaults.
Refer to the “BIOS Configuration / Setup“ section of this manual for details on BIOS setup.
9. Mounting the board to chassis
When fixing the Motherboard on a chassis it is recommended using screws with integrated washer and
having diameter of ~7mm.
Note: Do not use washers with teeth, as they can damage the PCB and may cause short circuits.
Installation procedure
Note: To clear all CMOS settings, including Password protection, move the Clear CMOS jumper in the
Clear CMOS position (with or without power) for ~10 sec. This will Load Failsafe Defaults and make sure
Secure CMOS is disabled.

KTQ67 Users Guide
KTD-N0829-C Page 9
1.2 Requirement according to IEC60950
Users of KTQ67 family boards should take care when designing chassis interface connectors in order to
fulfil the IEC60950 standard:
Lithium Battery precautions:
CAUTION!
Danger of explosion if battery is incorrectly
replaced.
Replace only with same or equivalent type
recommended by manufacturer.
Dispose of used batteries according
to the manufacturer’s instructions.
VORSICHT!
Explosionsgefahr bei unsachgemäßem
Austausch der Batterie.
Ersatz nur durch den selben oder einen vom
Hersteller empfohlenen gleichwertigen Typ.
Entsorgung gebrauchter Batterien nach
Angaben des Herstellers.
ADVARSEL!
Lithiumbatteri – Eksplosionsfare ved fejlagtig
håndtering.
Udskiftning må kun ske med batteri
af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandøren.
ADVARSEL
Eksplosjonsfare ved feilaktig skifte av batteri.
Benytt samme batteritype eller en tilsvarende
type anbefalt av apparatfabrikanten.
Brukte batterier kasseres i henhold til
fabrikantens
instruksjoner.
VARNING
Explosionsfara vid felaktigt batteribyte.
Använd samma batterityp eller en ekvivalent
typ som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt fabrikantens
instruktion.
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti
asennettu.
Vaihda paristo ainoastaan laltevalmistajan
suosittelemaan
tyyppiin. Hävitä käytetty paristo valmistajan
ohjeiden
mukaisesti.
When an interface/connector has a VCC (or other power) pin, which is directly connected to a power
plane like the VCC plane:
To protect the external power lines of the peripheral devices, the customer has to take care about:
•That the wires have suitable rating to withstand the maximum available power.
•That the enclosure of the peripheral device fulfils the fire protecting requirements of IEC60950.
Installation procedure

KTQ67 Users Guide
KTD-N0829-C Page 10
2 System Specification
2.1 Component main data
The table below summarizes the features of the KTQ67/Flex and KTQ67/ATXE embedded
motherboards.
Form factor
KTQ67/Flex: Flex-ATX (190,5 mm by 228,6 mm)
KTQ67/ATXE: ATX (190,5 mm by 304,8 mm)
Processor
Support the following 2nd Generation Intel® Core™ (Sandy Bridge) and Intel®
Pentium® Desktop processors via Socket H2 (LGA1155), ZIF Socket
•Intel® Core™ i7
•Intel® Core™ i5
•Intel® Core™ i3
•Intel® Pentium® Desktop
•1066/1333MHz system bus and 3/6/8MB internal cache.
(Intel® Pentium® Desktop G622 only 1066MHz)
•Up to 95W (Thermal Guideline)
Memory
•4x DDR3 UDIMM 240pin socket
•Support single and dual ranks DDR3 1066/1333MT/s
(PC3-8500/PC3-10600)
•Support system memory from 256MB and up to 4x 8GB
Note: Less than 4GB displayed in System Properties using 32bit OS
(Shared Video Memory/PCI resources is subtracted)
•ECC not supported (chipset limitation)
Chipset
Intel Q67 PCH (Platform Controller Hub)
•Intel ® VT-d (Virtualisation Technology for Directed I/O)
•Intel ® TXT (Trusted Execution Technology)
•Intel ® vPRO
•Intel ® AMT (Active Management Technology) version 7
•Intel ® AT (Anti-Theft Technology)
•Intel ® HD Audio Technology
•Intel ® RST (Rapid Storage Technology)
•Intel ® RRT (Rapid Recover Technology)
•SATA (Serial ATA) 6Gb/s and 3Gb/s.
•USB revision 2.0
•PCI Express revision 2.0
•ACPI 3.0b compliant
•Dual Display support (Dual Graphic Pipes)
•Blue-ray HD video playback
Security
•Intel® Integrated TPM 1.2 support
Management
•Intel® Active Management Technology (Intel® AMT) 7.0
Audio
Audio, 7.1 Channel High Definition Audio Codec using the VIA 1708B codec
•Line-out
•Line-in
•Surround output: SIDE, LFE, CEN, BACK and FRONT
•Microphone: MIC1 and MIC2
•CDROM in
•SPDIF (electrical Interface only)
•On-board speaker (Electromagnetic Sound Generator like Hycom HY-05LF)
System Specification

KTQ67 Users Guide
KTD-N0829-C Page 11
Video
Intel ® i3, i5 or i7 processor supports Intel ® HD Graphics 2000/3000.
Intel ® Pentium Desktop ® Processor supports Intel ® HD Graphics.
Analogue VGA and digital display ports (2x DP) via the Mobile Intel ® QM67 Chipset.
•VGA (analogue panel)
•DP (DisplayPorts) dual, comply with DisplayPort 1.1a specification.
•LVDS panel support up to 24 bit, 2 pixels/clock and 1920x1200.
•HDMI panel support via DP to HDMI Adapter Converter.
•Second VGA panel support via DP to VGA Adapter Converter
•Second DVI panel support via DP to DVI Adapter Converter
•Dual independent pipes for Mirror and Dual independent display support
•LVDS up to two pixel/clock 24 bit (optional)
I/O Control
Via ITE IT8516E Embedded Controller and Winbond W83627DHG I/O Controller
(both via LPC Bus interface)
Peripheral
interfaces
•Six USB 2.0 ports on I/O area
•Eight USB 2.0 ports on internal pinrows
•Four Serial ports (RS232) on internal pinrows
•Two Serial ATA-600 IDE interfaces (blue)
•Four Serial ATA-300 IDE interfaces (black)
•RAID 0/1/5/10 support
•mSATA via mSATA connector
•PS/2 keyboard and mouse ports via pinrow
LAN
Support
•1x 10/100/1000Mbits/s LAN (ETHER1) using Intel® Lewisville 82579LM Gigabit
PHY connected to Q67 supporting AMT 7.0
•2x 10/100/1000Mbits/s LAN (ETHER2/ETHER3)using Intel® Hartwell 82574L PCI
Express controllers
•PXE Netboot supported.
•Wake On LAN (WOL) supported
Expansion
Capabilities
•PCI Bus routed to PCI slot(s) (PCI Local Bus Specification Revision 3.0, 33MHz)
oKTQ67/Flex: 2
oKTQ67/ATXE: 5
•PCI-Express slot(s) (PCIe 2.0), for all KTQ67 family members:
o1 slot PCIe x16
o1 slot PCIe x4 (in a x16 slot) (EFT samples support only PCIe x1)
o1 slot miniPCI-Express
•SMBus, compatible with ACCES BUS and I2C BUS, (via Feature connector)
•SPI bus routed to SPI connector
•DDC Bus routed to DP connector when DP Adapters are connected
•5 x digital input, (via Feature connector)
•13 x GPIOs (General Purpose I/Os), (via Feature connector)
•DAC, ADC, PWM and TIMER (Multiplexed), (via Feature connector)
•WAKE UP / Interrupt Inputs (Multiplexed), (via Feature connector)
•3 Wire Bus for GPIO Expansion (up to 152 GPIOs), (via Feature connector)
•8 bit Timer output, (via Feature connector)
System Specification

KTQ67 Users Guide
KTD-N0829-C Page 12
Hardware
Monitor
Subsystem
•Smart Fan control system, support Thermal® and Speed® cruise for FAN_CPU
•CPU die temperature input (Precision +/- 3ºC)
•Voltage monitoring
•Intrusion (Case Open) detect input, (via Feature connector)
•Sleep S4/S5# Indication, (via Feature connector)
•System Powergood Signal, (via Feature connector)
Power
Supply Unit
ATX/BTX (w. ATX+12V) PSU for full PCI/PCIe load.
Battery
Exchangeable 3.0V Lithium battery for on-board Real Time Clock and CMOS RAM.
Manufacturer Panasonic / Part-number CR-2032L/BN, CR2032N/BN or CR-2032L/BE.
Approximate 5 years retention.
Current draw is 5,7µA when PSU is disconnected and 0 µA in S0 – S5.
CAUTION: Danger of explosion if the battery is incorrectly replaced. Replace
only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
BIOS
•Kontron Technology / AMI BIOS (EFI core version)
•Support for ACPI 3.0 ( Advanced Configuration and Power Interface), Plug & Play
oSuspend (S1 mode)
oSuspend To Ram (S3 mode)
oSuspend To Disk (S4 mode)
•“Always On” BIOS power setting
•RAID Support (RAID modes 0,1, 5 and 10)
Operating
Systems
Support
•WinXP (not tested yet)
•Windows 7
•WES7
•Linux (not ready yet)
•VxWorks (not ready yet)
System Specification

KTQ67 Users Guide
KTD-N0829-C Page 13
Environmental
Conditions Operating:
0°C – 60°C operating temperature (forced cooling). It is the customer’s
responsibility to provide sufficient airflow around each of the components to keep
them within allowed temperature range.
10% - 90% relative humidity (non-condensing)
Storage:
-20°C – 70°C; lower limit of storage temperature is defined by specification
restriction of on-board CR2032 battery. Board with battery has been verified for
storage temperature down to -40°C by Kontron.
5% - 95% relative humidity (non-condensing)
Electro Static Discharge (ESD) / Radiated Emissions (EMI): (Pending)
All Peripheral interfaces intended for connection to external equipment are ESD/
EMI protected.
EN 61000-4-2:2000 ESD Immunity
EN55022:1998 class B Generic Emission Standard.
Safety:
IEC 60950-1: 2005, 2nd Edition
UL 60950-1
CSA C22.2 No. 60950-1
Product Category: Information Technology Equipment Including Electrical
Business Equipment
Product Category CCN: NWGQ2, NWGQ8
File number: E194252
Theoretical MTBF:
211.994 / 100.475 hours @ 40ºC / 60ºC for the KTQ67/Flex
200.897 / 94.529 hours @ 40ºC / 60ºC for the KTQ67/ATXE
Restriction of Hazardous Substances (RoHS):
All boards in the KTQ67 family are RoHS compliant.
Capacitor utilization:
No Tantalum capacitors on board
Only Japanese brand Solid capacitors rated for 100 ºC used on board
System Specification

KTQ67 Users Guide
KTD-N0829-C Page 14
2.2 System overview
The block diagram below shows the architecture and main components of the KTQ67. The key
component on the board is the Intel®QM67 (Cougar Point) Mobile Express Chipset.
Some components (PCI/PCIe/miniPCIe slots) are optional depending on board type.
More detailed block diagram on next page.
System Specification

KTQ67 Users Guide
KTD-N0829-C Page 15
System Specification
ATXE only
(optionally)

KTQ67 Users Guide
KTD-N0829-C Page 16
2.3 Processor Support Table
The KTQ67 is designed to support the following LGA1155 processors (up to 95W power consumption):
2nd generation Intel® Core™ i7 processor
2nd generation Intel® Core™ i5 processor
2nd generation Intel® Core™ i3 processor
Intel® Pentium® Desktop processor
In the following list you will find all CPU’s supported by the chipset in according to Intel but also other
CPU’s if successfully tested.
Embedded CPU’s are indicated by green text, successfully tested CPU’s are indicated by highlighted
text, successfully tested embedded CPU’s are indicated by green and highlighted text and failed
CPU’s are indicated by red text.
Some processors in the list are distributed from Kontron, those CPU’s are marked by an * (asterisk).
However please notice that this marking is only guide line and maybe not fully updated.
Processor
Brand
Clock
Speed
[GHz]
Turbo
Speed
[GHz]
Cores /
Threads Bus Speed [MHz]
Cache
[MB]
CPU
Number sSpec no. Step.
Thermal
Guideline
[Watt]
3.4
3.8
4 / 8
1066/1333
8
2600
SR00B
D2
95
3.4
3.8
4 / 8
1066/1333
8
2600K
SR00C
D2
95
2.8
3.8
4 / 8
1066/1333
8
2600S
SR00E
D2
65
3.3
3.7
4 / 4
1066/1333
6
2500K
SR008
D2
95
3.3
3.7
4 / 4
1066/1333
6
2500
SR00T
D2
95
3.1
3.4
4 / 4
1066/1333
6
2400
SR00Q
D2
95
2.7
3.7
4 / 4
1066/1333
6
2500S
SR009
D2
65
2.7
3.5
2 / 4
1066/1333
3
2390T
SR065
-
35
2.5
3.3
4 / 4
1066/1333
6
2405S
SR0BB
D2
65
2.5
3.3
4 / 4
1066/1333
6
2400S
SR00S
D2
65
2.3
3.3
4 / 4
1066/1333
6
2500T
SR00A
D2
45
3.4
-
2 / 4
1066/1333
3
2130
SR05W
-
65
3.3
-
2 / 4
1066/1333
3
2125
SR0AY
J1
65
3.3
-
2 / 4
1066/1333
3
2120
SR05Y
-
65
3.1
-
2 / 4
1066/1333
3
2105
SR0BA
J1
65
3.1
-
2 / 4
1066/1333
3
2100
SR05C
-
65
(no vPRO)
3.1
-
2 / 4
1066/1333
3
2102
SR05D
-
65
2.6
-
2 / 4
1066/1333
3
2120T
SR060
-
35
2.5
-
2 / 4
1066/1333
3
2100T
SR05Z
-
35
3.0
-
2 / 2
1066/1333
3
G860
SR058
-
65
2.9
-
2 / 2
1066/1333
3
G850
SR05Q
-
65
2.8
-
2 / 2
1066/1333
3
G840
SR05P
-
65
2.7
-
2 / 2
1066
3
G632
-
-
65
2.7
-
2 / 2
1066
3
G630
SR05S
-
65
2.6
-
2 / 2
1066
3
G620
SR05R
-
65
(no vPRO)
2.6
-
2 / 2
1066
3
G622
-
-
65
2.2
-
2 / 2
1066
3
G620T
SR05T
-
35
2.3
-
2 / 2
1066
3
G630T
SR05U
-
35
2.5
-
2 / 2
1066
2
G540
SR05J
-
65
2.4
-
2 / 2
1066
2
G530
SR05H
-
65
2.0
-
2 / 2
1066
2
G530T
SR05K
-
35
(no vPRO)
1.6
-
1 / 1
1066
1
G440
SR0BY
-
35
System Specification

KTQ67 Users Guide
KTD-N0829-C Page 17
!
Warning: Make sure sufficient airflow is always present around the components located below
the cooler. Different coolers are available on the market and some is not generating any airflow
or is blocking the airflow around these components, causing reduced lifetime.
Not all CPU even of same type support all functions ex. i7 2600K and i5 2500K doesn’t support vPro.
All the CPUs in the list above, inclusive the Pentium Desktop processors, but except G440, are
supporting the Enhanced Intel® SpeedStep® which is improved SpeedStep technology for faster
transition between voltage (power saving states) and frequency states with the result of improved
power/performance balance.
Intel® Turbo Boost Technology 2.0 is supported by i5 and i7, as indicated in above list of processors,
and is enabling overclocking of all cores, when operated within the limits of thermal design power,
temperature and current.
Sufficient cooling must be applied to the CPU in order to remove the effect as listed in above table
(Thermal Guideline). The sufficient cooling is also depending on the maximum (worst-case) ambient
operating temperature and the actual load of processor.
It is recommended to use a cooler like the Kontron
PN 1046-6305 “KTQ67 Cooler”.
The design of this cooler makes sure airflow is
always present around the components below the
cooler. Even if Fan is set to be off, it is still running
a minimum RPM (Rotation Per Minute).
Air sucked in to the cooler
Air blown out of the cooler
Components below the cooler
System Specification
Note: The temperature of the air blown out of the cooler should be 70
º
C maximum.

KTQ67 Users Guide
KTD-N0829-C Page 18
2.4 System Memory support
The KTQ67/FLEX and /ATXE have four DDR3 UDIMM sockets. The sockets support the following
memory features:
•4x DDR3 1.5V UDIMM 240-pin
•Dual-channel with 2 UDIMM per channel
•Single/dual rank unbuffered 1066/1333MT/s (PC3-8500/PC3-10600)
From 256MB and up to 4x 8GB.
Note: Less than 4GB displayed in System Properties using 32bit OS
(Shared Video Memory/PCI resources is subtracted)
•SPD timings supported
•ECC not supported
The installed DDR3 DIMM should support the Serial Presence Detect (SPD) data structure. This allows
the BIOS to read and configure the memory controller for optimal performance. If non-SPD memory is
used, the BIOS will attempt to configure the memory settings, but performance and reliability may be
impacted.
Memory Operating Frequencies
Regardless of the DIMM type used, the memory frequency will either be equal to or less than the
processor system bus frequency. For example, if DDR3 1600 memory is used with a 1333 MHz system
bus frequency processor, the memory clock will operate at 666 MHz. The table below lists the resulting
operating memory frequencies based on the combination of DIMMs and processors.
DIMM Type
Module
name
Memory
Data
transfers
[Mill/s]
Processor
system bus
frequency
[MHz]
Resulting
memory clock
frequency
[MHz]
Peak transfer
rate
[MB/s]
DDR3 1066
PC3-8500
1066
1066 / 1333
533
8533
DDR3 1333
PC3-10600
1333
1333
666
10666
DDR3 1600
PC3-12800
1600
1333
666
10666
Notes: Kontron offers the following memory modules:
1028-6891 1GB DDR3 1066
1030-5747 2GB DDR3 1066
1030-5722 1GB DDR3 1333
1028-6892 2GB DDR3 1333
1050-3141 4GB DDR3 1333
1050-3780 8GB DDR3 1333
In order to support Intel ® AMT (Management Engine) SLOT A0 must always be populated.
DDR3 (SLOT B1)
DDR3 (SLOT B0)
DDR3 (SLOT A1)
DDR3 (SLOT A0)
(Example Flex version)
System Specification

KTQ67 Users Guide
KTD-N0829-C Page 19
2.5 KTQ67 Graphics Subsystem
The KTQ67 equipped with Intel ® i3, i5 or i7 processor, supports Intel ® HD Graphics 2000/3000.
The KTQ67 equipped Intel ® Pentium Desktop ® Processor, supports Intel ® HD Graphics.
All KTQ67 versions support analogue VGA and digital display ports (2x DP) via the Intel ® Q67 Chipset.
Optionally LVDS support.
The DP interface supports the DisplayPort 1.1a specification. The PCH supports High-bandwidth Digital
Content Protection for high definition content playback over digital interfaces. The PCH also integrates
audio codecs for audio support over DP interfaces.
Up to two displays (any two display outputs) can be activated at the same time and be used to
implement dual independent display support or mirror display support. PCIe and PCI graphics cards can
be used to replace on-board graphics or in combination with on-board graphics.
2.5.1 Intel® HD Graphics 3000
Features of the Intel HD Graphics 3000 build into the i3, i5 and i7 processors, includes:
•High quality graphics engine supporting
oDirectX10.1 and OpenGL 3.0 compliant
oShader Model 4.1 support
oIntel ® Clear Video HD Technology
oIntel ® Quick Sync Video Technology
oIntel ® Flexible Display Interface (Intel ® FDI)
oCore frequency of 350 - 1300 (Turbo) MHz
oMemory Bandwidth up to 21.3 GB/s
o12 3D Execution Units
o1.62 GP/s and 2.7 GP/S pixel rate (DP outputs)
oHardware Acceleration full MPEG2, full VC-1 and full AVC
oDynamic Video Memory Technology (DVMT) support up to 1720 MB
•LVDS panel Support (optional), 18/24 bit colours in up to WUXGA (1920x1200) @60 Hz and
SPWG (VESA) colour coding. OpenLDI (JEIDA) colour coding is 18 bit with or without Dithering.
•DP0 and DP1
o24/30 bit colours in WQXGA (2560x1600 pixels) and HDCP.
Use of DP Adapter Converters can implement HDMI
support or second VGA or DVI panel support.
The HDMI interface supports the HDMI 1.4a specification
and includes audio codecs. However limitations to the
resolution apply:
2048x1536 VGA
1920x1200 HDMI and DVI DP to VGA DP to HDMI DP to DVI-D
PN 1045-5779 PN 1045-5781 PN 1045-5780
System Specification

KTQ67 Users Guide
KTD-N0829-C Page 20
2.6 Power Consumption
In order to ensure safe operation of the board, the ATX12V power supply must monitor the supply
voltage and shut down if the supplies are out of range – refer to the hardware manual for the actual
power supply specification. The KTQ67 board is powered through the ATX/BTX connector and
ATX+12V connector. Both connectors must be used in according to the ATX12V PSU standard.
The requirements to the supply voltages are as follows:
Supply
Min
Max
Note
VCC3.3 3.168V 3.432V Should be ±4% for compliance with the ATX specification
Vcc 4.75V 5.25V Should be ±5% for compliance with the ATX specification.
Should be minimum 5.00V measured at USB connectors
in order to meet the requirements of USB standard.
+12V 11.4V 12.6V Should be ±5% for compliance with the ATX specification
–12V –13.2V –10.8V Should be ±10% for compliance with the ATX specification
-5V -5,50V -4.5V Not required for the KTQ67 board
5VSB 4.75V 5.25V Should be ±5% for compliance with the ATX specification
More detailed Static Power Consumption
On the following pages the power consumption of the KTQ67 Board is measured under:
1- DOS, idle, mean
2- Windows7, Running 3DMARK 2005 & BiT 6, mean
3- S1, mean
4- S3, mean
5- S4, mean
The following items were used in the test setup:
Low Power Setup
Standard system configuration equipped with PCI card, Internal graphics, 2x SATA disks, Intel i3
CPU, 2x DIMM (1GB Modules), CRT Monitor, Keyboard & Mouse. 1x 1-4GB USB Flash Stick.
High Power Setup
Standard system configuration equipped with PCI card, PCIex4, PCIex16, miniPCIe WLAN, 4x
SATA disks, Intel i7 CPU, 4x DIMM (2+2+2+1 Modules), CRT Monitor, Keyboard & Mouse, 4x 1-
4GB USB Flash Stick.
1. 12V active cooler (Intel BOX).
2. USB Keyboard/Mouse Genius
3. CRT Sampo AlphaScan 912
4. 2.5” HDD Fujitsu MHY2120BH
5. ATX Fortron 400W
6. Tektronix TDS5104B
7. Tektronix TCPA300
8. Tektronix TCP312
9. Fluke 289
10. ATX rail switch
Note: The Power consumption of Display and HD are not included.
ATX supplies
KTQM67
PSU
Gnd
Current
Probe
Tektronix TDS5104B
System Specification