Kontron Mungo540 User manual

Mungo540
Embedded Socket 370 CPU Board
Version 1.0
User’s Manual

ii
Customer Service
Mailing Address: Kontron - United States
6260 Sequence Drive
San Diego, CA 92121 USA
Tel: [phone]
Fax: [phone]
Technical Support: U.S. and Canadian Customers - 24 hours a day
Tel: [phone], option 1
Fax: [phone]
International Customers - 9am to 4pm local time
Tel: [phone]
Fax: [phone]
Visit our site at: www.kontron.com
© 2002 Kontron, an International Corporation. All rights reserved.
The information in this user’s guide is provided for reference only.
Kontron does not assume any liability arising out of the application or
use of the information or products described herein. This user’s guide
may contain or reference information and products protected by
copyrights or patents and does not convey any license under the patent
rights of Kontron, nor the rights of others.
Kontron is a registered trademark of Kontron. All trademarks,
registered trademarks, and trade names used in this user’s guide are the
property of their respective owners. All rights reserved. Printed in the
United States of America and Canada. This user’s guide contains
information proprietary to Kontron. Customers may reprint and use this
user’s guide in other publications. Customers may alter this user’s guide
and publish it only after they remove the Kontron name, cover, and
logo.
Kontron reserves the right to make changes without notice in product or
component design as warranted by evolution in user needs or progress
in engineering or manufacturing technology. Changes which affect the
operation of the unit will be documented in the next revision of this
user’s guide.

iii
Acknowledgments
Award is a registered trademark of Award Software International, Inc.
PS/2 is a trademark of International Business Machines Corporation.
SMI is a trademark of Silicon Motion and Technologies Inc.
Intel Pentium and Coppermine are registered trademarks of Intel
Corporation.
Microsoft Windows is a registered trademark of Microsoft Corporation.
All other product names or trademarks are properties of their respective
owners.

iv
Regulatory Compliance Statements
This section provides the FCC compliance statement for Class A
devices and describes how to keep the system CE compliant.
FCC Compliance Statementfor Class A Devices
The product(s) described in this user’s guide has been tested and found
to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the user’s guide, may cause harmful interference to
radio communications. Operation of this equipment in a residential area
(domestic environment) is likely to cause harmful interference, in which
case the user will be required to correct the interference (take adequate
measures) at their own expense.
Changes or modifications not expressly approved by Kontron could
void the user's authority to operate the equipment.
Note: The assembler of a personal computer system may be required to
test the system and/or make necessary modifications if a system is
found to cause harmful interference or to be noncompliant with the
appropriate standards for its intended use.
CECertification
The product(s) described in this user’s guide complies with all
applicable European Union (CE) directives if it has a CE marking. The
CE declaration of conformity is provided on the last page of this user’s
guide. For computer systems to remain CE compliant, only CE-
compliant parts may be used. Maintaining CE compliance also requires
proper cable and cabling techniques. Although Kontron offers
accessories, the customer must ensure that these products are installed
with proper shielding to maintain CE compliance. Kontron does not
offer engineering services for designing cabling systems. In addition,
Kontron will not retest or recertify systems or components that have
been reconfigured by customers.

v
Guarantee and Warranty Policy
Guarantee
A thirty day money-back guarantee is provided on all standard products
sold. Special order products are covered by our Limited Warranty,
however they may not be returned for refund or credit. EPROMs, RAM,
Flash EPROMs or other forms of solid electronic media are not
returnable for credit - but for replacement only. An extended warranty
is available. Consult the factory.
Refunds
In order to receive a refund on a product for the purchase price, the
product must not have been damaged by the customer or by the
common carrier chosen by the customer to return the goods and the
product must be returned complete (meaning all user’s guides, software,
cables, etc.) within 30 days of receipt and in an as-new and resalable
condition. The “ Error! Reference source not found.” must be
followed to assure a prompt refund.
Restocking Charges
Product returned after 30 days, and before 60 days, of the purchase will
be subject to a minimum 20% restocking charge and charges for any
damaged or missing parts. Products not returned within 60 days of
purchase, or products which are not in an as-new and resaleable
condition, are not eligible for a credit return and will be returned to the
customer.
Limited Warranty
Effective April 1, 1998, all products carry a 2-year limited warranty.
Within 2 years of purchase, Kontron will repair or replace, at our
option, any defective product. Kontron will service the warranty for all
standard catalog products for the first two years from the date of
shipment. Please note: The 2-year warranty may not apply to special
promotion items. Please consult the factory for warranty verification.

vi
The limited warranty is void if the product has been subjected to
alteration, neglect, misuse, or abuse; if any repairs have been attempted
by anyone other than Kontron or its authorized agent; or if the failure is
caused by accident, acts of God, or other causes beyond the control of
Kontron or the manufacturer. Neglect, misuse, and abuse shall include
any installation, operation, or maintenance of the product other than in
accordance with the user’s guide.
No agent, dealer, distributor, service company, or other party is
authorized to change, modify, or extend the terms of this Limited
Warranty in any manner whatsoever. Kontron reserves the right to make
changes or improvements in any product without incurring any
obligation to similarly alter products previously purchased.
Return Procedure
For any Guarantee or Limited Warranty return, please contact Kontron
Customer Service at 800-480-0044 or 858-677-0877 and obtain a
Return Material Authorization (RMA) Number. All product(s) returned
to Kontron for service or credit must be accompanied by a Return
Material Authorization (RMA) Number. Freight on all returned items
must be prepaid by the customer who is responsible for any loss or
damage caused by common carrier in transit. Returns for Warranty
must include a Failure Report for each unit, by serial number(s), as well
as a copy of the original invoice showing the date of purchase.
To reduce risk of damage, returns of product must be in an Kontron
shipping container. If the original container has been lost or damaged,
new shipping containers may be obtained from Kontron Customer
Service at a nominal cost.
Kontron owns all parts removed from repaired products. Kontron uses
new and reconditioned parts made by various manufacturers in
performing warranty repairs and building replacement products. If
Kontron repairs or replaces a product, its warranty term is not extended.
Kontron will normally return your replacement or repaired items via
Second Day Air. Overnight delivery or delivery via other carriers is
available at an additional charge.
Shipments not in compliance with this Guarantee and Limited Warranty
Return Policy will not be accepted by Kontron.

vii
Limitation ofLiability
In no event shall Kontron be liable for any defect in hardware, software,
loss, or inadequacy of data of any kind, or for any direct, indirect,
incidental, or consequential damages in connection with or arising out
of the performance or use of any product furnished hereunder.
Kontron’s liability shall in no event exceed the purchase price of the
product purchased hereunder. The foregoing limitation of liability shall
be equally applicable to any service provided by Kontron or its
authorized agent.
Some sales items and customized systems are not subject to the
guarantee and limited warranty. However in these instances, any
deviations will be disclosed prior to sales and noted in the original
invoice. Kontron reserves the right to refuse returns or credits on
software or special order items.

RI7SM User’s Manual viii
Contents
Chapter 1 Introduction .................................................1
Checklist.....................................................................2
Introduction................................................................3
Specifications ..............................................................3
Intelligence .................................................................6
Chapter 2 Installations .................................................8
CPU Installation..........................................................9
Memory Installation.................................................10
Jumpers on the Mungo540.......................................11
Connectors on the Mungo540 ..................................16
Watchdog Timer Configuration................................31
Chapter 3 BIOS Configuration..................................34
Chapter 4 815EP Chipset Driver Installation Guide . ...62
Chapter 5VGA Driver Installation Guide……….……..64
Chapter 6Audio Driver Installation Guide…….…….…66
Chapter7 LAN Driver Installation Guide……….……..68
Chapter 8Ultra ATA IDE Driver Installation Guide…..80
Appendix.........................................................................82
A. I/O Port Address Map.........................................83
B. Interrupt Request Lines (IRQ)..........................84

RI7SM User’s Manual 1
Chapter 1
Introduction
Thismanualisdesignedto give you information on the Mungo540 single
board computer. It is divided into the following sections:
Checklist...................................................................................................2
Introduction.............................................................................................3
Specifications..........................................................................................3
Intelligence..............................................................................................6
The topics covered in this chapter are as follows:
uChecklist
uDescription
uFeatures
uSpecifications
uIntelligence

2Mungo540 User’s Manual
Checklist
Please check that your package is complete and contains the items below.
If you discover damaged or missing items, please contact your dealer.
• Mungo540 single board computer
• This user’s manual
• 4 IDE ribbon cable
• 1 Floppy ribbon connector
• 1 Keyboard/ Mouse cable
• 1 CRT cable
• 1 COM port cable for COM1~4
• 1 Sound cable
• 1 IPC Series (CD driver)
• 1 USB cable support two channel
• 1 ATX power cable

RI7SM User’s Manual 3
Introduction
The Mungo540 is one of the most efficient embedded boards in the world. It
integrates the Intel 82815EP chipset and Intel 82801BA ICH2 chipset
supporting a Socket 370 connector for Intel Pentium III with frequencies
of up to 1G MHz.
The Mungo540 is designed with a PCI bridge that is able to support 1 PCI
master interfaces with PCI to ISA bridge by PC/104 interface. The board
also provides DiskOnChip interface to storage your system. We also
providesCRT/LCDdisplay,ACP7Codec to show the best solution on this
board. Dual LAN function also offer the customs demands.
Specifications
• Processor Socket: Socket 370 connector
• Processor: Intel Pentium III 500MHz~1GHz Processor
• Bus Speed:100MHz, 133MHz.
• Chipset: Intel 815EP Chipset
• Secondary Cache: CPU integrated
• Memory Sockets:
One 168-pin DIMM sockets
Max. 256MB SDRAM
Memory type: SDRAM (Synchronous DRAM)
NOTE:Only SDRAMmodules thatsupport SPD(Serial Presence
Detect) should be use. Use PC133 modules when running
133MHz CPU bus speed and use PC66/PC100 modules when
running 66MHz /100MHz CPU bus speed.

4Mungo540 User’s Manual
• BIOS: Award BIOS, PnP support
• The motherboard BIOS provides “Plug & Play” which detects
the peripheral devices and expansion boards of the
automatically.
• The motherboard provides a Desktop Management Interface
(DMI)functionwhichrecordyourmotherboardspecifications
• ACPI Power management
• DMI BIOS Support:
Desktop Management Interface (DMI) allows users to download
systemhardware-levelinformation such asCPU type, CPUspeed,
internal/external frequencies and memory size.
• 1ST I/O PCI to ISA Bridge: Winbond W83627HF + W83628F +
W83629D
• 2ND I/O: Winbond W83877TTF
• Parallel Port: One high-speed parallel port, SPP/EPP/ECP mode
• Serial Port: Four 16550 UART compatible ports with
COM1/COM3/ COM4 as RS232 and COM2 as RS232/RS422/RS485
• Enhanced IDE: Two Bus Mastering EIDE mode, up to 4 devices,
Two EIDE interfaces for up to four devices, support PIO Mode 4/5
or Ultra DMA/33 IDE Hard Disk and ATAPI CD-ROM.
• FDD Interface:Twofloppydrives (360KB, 720KB, 1.2MB, 1.44MB,
2.88MB, LS-120)
• USB Interface: Four USB pin-header connectors, compliant with
USB Specification Rev. 1.1
• DiskOnChip:TheM-Systemsflask disk supportssystem boot and
storage capacity from 8MB to 288MB.
• Watchdog Timer: 0~254.5-level, programmable
• IrDA Interface: Pin-header connector for the optional IrDA
external connector
• Keyboard and Mouse Connectors: PS/2 type mini-DIN that
supports PC/AT; supports a 5-pin external keyboard connector

RI7SM User’s Manual 5
• VGA: Onboard SMI721 4/8M VGA Chipset support Single TFT
LCD panel (36 bit)
• Simultaneous CRT & LCD display
• LCD panel supports DSTN/TFT
• 1280x1024x8bpp colors CRT resolution
• Up to 1280x1024x8bpp colors resolution for color active
matrix TFT panels (12, 18, and 24bit analog) or (12+12),
(18+18) double pixel/CLK interface
• LVDS Panel support (18 bit) for JAE Connector
• Green Function: Power management via BIOS, activated through
mouse/keyboard movement.
• LAN: Intel82559BandIntel82562ET LAN Controllers Interface for
Connecting to the ICH2
• Sound:
AD1881 AC’97 CODEC for controller Interface for Connection to
ICH2
• Environmental and Mechanical:
• Power Supply: 10A @+5V(max), ±12V: 100mA(max)
• Temperature: 0°C to 60°C
• Humidity: 5% to 95%
• Dimensions: 146mm x 203mm

6Mungo540 User’s Manual
Intelligence
• Temperature Monitoring and Alert: A sensor for the CPU
temperatureon the Mungo540monitors the CPUtemperature and alerts
the user through the speaker or buzzer when temperature exceeds
the safe heat level.
• Windows serials shut-off: Allows shut-off control from within
Windows serials and through an ATX power supply.
• Year 2001 Compliant BIOS: The onboard Award BIOS is Year
2001 Compliant and will pass software applications that have the
tendency to invoke INT1AH function 04H such as year2000.exe
utility released by NSTL.
• Wake On LAN: Through an ATX power supply and network
connection, systems can be turned on from the power-off state.
Wake On LAN will function properly only with an ATX power
supply with 5VSB that has 800mA.

RI7SM User’s Manual 7
This page was intentionally left blank

8Mungo540 User’s Manual
Chapter 2
Installations
This chapter provides information on how to use the jumpers and
connectorsonthe Mungo540 in order toset up a workable system.The topics
covered are:
CPU Installation......................................................................................9
Memory Installation.............................................................................10
Jumpers on the Mungo540..................................................................11
Connectors on the Mungo540............................................................16
Watchdog Timer Configuration.........................................................31
CAUTION: Danger of explosion if
battery is incorrectly replaced. Replace
only with the same or equivalent type
recommended by the manufacturer.

RI7SM User’s Manual 9
CPU Installation
The Mungo540 single board computer supports a Socket 370 connector
processor socket for Intel Pentium III processors.
The Socket 370 connector comes with a lever to secure the processor.
Before inserting the CPU, make sure the lever is raised perpendicular to
the socket and the notch on the corner of the CPU corresponds with the
notch on the inside of the socket.
After you have installed and lock the processor into place, check if the
jumpers for the CPU type and speed are correct.
NOTE:
Ensure that the CPU heat sink and the CPU top surface are in
total contact to avoid CPU overheating problem that would
cause your system to hang or be unstable.

10 Mungo540 User’s Manual
Memory Installation
The Mungo540 single board computer supports one 168-pin DIMM
socket for a maximum total memory of 256MB SDRAM.
NOTE: Use SDRAM module with PC133 specification when running
133MHz CPU bus speed. With 66/100MHz bus speed,
SDRAM modules with PC66 or PC100 specification can be
used.

RI7SM User’s Manual 11
Jumpers on the Mungo540
The jumpers on the Mungo540 allow you to configure your board
accordingto theneeds ofyour applications.If youhave doubtsabout the
best jumper configuration for your needs, contact your dealer or sales
representative. The following table lists the connectors on Mungo540 and
their respective functions.
Jumper Locations on the Mungo540...............................................12
JP1: Clear CMOS Content..........................................................13
JP2: Panel Power Setting............................................................13
JP4: Boot Block Lock/Unlock....................................................13
JP5: Select Panel Display Type Setting....................................14
JP6: COM3/COM4 RS232 +5V / +12V Power Setting.............14
JP8: COM1/COM2 RS232 +5V / +12V Power Setting.............14
JP9: DiskOnChip BIOS Expansion Address Select................15
JP10: RS232/422/485 Selection...................................................15
The following examples showthe conventions used in this section.
Jumper Open
Jumper Closed

12 Mungo540 User’s Manual
Jumper Locations on the Mungo540
DISK ON CHIP
JP1: Clear CMOS Content
JP2: Panel Power Setting
JP4: Boot Block Lock/Unlock
JP5: Select Panel Display Type Setting
JP6: COM3/COM4 RS232 +5V / +12V Power Setting
JP8: COM1/COM2 RS232 +5V / +12V Power Setting
JP9: DiskOnChip BIOS Expansion Address Select
JP10: RS232/422/485 Selection