Kontron EBP-11A4B6 User manual

eBP-11A4B6
eBP-11A4B6eBP-11A4B6
Version 1.3
11-Slot ePCI Active Backplane
QUICK REFERENCE
Board Rev.
0
1
J27
J11
J14
1J9
J13 J12
J5
J4
J3
J1
J2
J31
FAN5
1
12
-12V
SPEAKER
N.C.
KBCLK
GND
GND
+12V +5V KBDAT
-5V RESET
+3.3V
1
J12
J13
1
1
1
12
13
24
1 4
W1
W2
12
6
5
J15J16J17J18J19J20
A1 A2 B1 B2 A1 A2 B1 B2 A1 A2 B1 B2 A1 A2 B1 B2 A1 A2 B1 B2 A2 B1 B2
A93 A94
B93
B94
A93 A94 B93 B94 A93 A94 B93 B94 A93 A94 B93 B94 A93 A94 B93 B94 A93 A94 B93 B94
HiNT R
PCI-X to PCI-X
Bridge
64-Bit/133MHz
HB8
HiNT R
PCI-X to PCI-X
Bridge
64-Bit/133MHz
HiNT R
PCI-X to PCI-X
Bridge
64-Bit/133MHz
Slot 1 Slot 0 Slot 0 Slot 1 Slot 2 Slot 3
BUS C BUS D
BUS A
JUMPER SETTINGS
(* : Default Setting)
JUMPER SETTINGS
(* : Default Setting)
W10 W7Bus A, Bus B Max. Speed
Mode Bus A & B Speed Jumper
PCI 33MHz or Less 1-2, 3-4
PCI 33MHz to 66MHz 3-4
PCI-X 50MHz to 66MHz 5-6
PCI-X 100MHz to 133 MHz None
First Level Debugging
1. - If +12V is needed to power the SHB : Either connect +12V power supply cable in +12V SHB connector or in J4 and/or J7 of backplane. For single host power
by backplane connect J11 with SHB +12V connector with a custom cable.
2. - Remove all peripheral boards and SHB
3. - Remove all cables from backplane.
4. - Make sure that all the power LEDs are ON.
5. - If ok, re-insert SHB and all I/O boards in backplane, reinstall all cables, and set all bus in SAFE MODE (see setting jumpers) and reboot.
6. - To get maximum speed check the SHB and I/O maximum speed limit. CPLD can also affect the bus speed by either safe/autodetect mode jumper setting or the
position of I/O cards into slots. Make sure that BUS speed jumpers are removed.
Device PCI IDSEL REQ/ INT CLK
Bus# GNT
Slot 0
Slot 1
Slot 2
Slot 3
Slot 0
Slot 1
Slot 0
Slot 1
Slot 0
Slot 1
Slot 2
Slot 3
D
D
D
D
C
C
B
B
A
A
A
A
31
30
29
28
31
30
31
30
31
30
29
28
(1)
0
1
2
3
0
1
0
1
0
1
2
3
A
B
C
D
A
B
A
B
A
B
C
D
B
A
D
C
A
D
--
--
B
C
D
A
12
56
W7
PWRG1
PWRG2
3.3VSB
3.3V
+5V
+5VSB
-5V
+12V
-12V
J10
Note: As per PCI-X Electrical subgroup simulation report a Safe Mode jumper has
been set to ensure functionality. An autodetect jumper has been added to support
faster bus speed based on hardware qualification report. To use this feature you
should qualify the PCI bus with your own I/O boards.
Note
Jumper W11 (7-8) installed, W2 removed and I/O board supporting PCI-X 133MHz
inserted with at least one empty slot between each I/O inserted in the bus D.
For 133MHz operation (with one I/O board only)
Jumper W11 (7-8) installed, W2 removed and I/O board supporting PCI-X
133MHz inserted anywhere in the bus D.
For 100MHz operation (with two I/O boards only)
ATX POWER
(1) IDSEL 31 for Standard Option
IDSEL 27 for KCI ePCI-200 & ePCI-201 Option
see Table Bus ASlot 0 config jumper
W2 W6Bus D, Bus C Maximum speed
MODE BUS C & D SPEED Jumper
PCI 33MHz
PCI 66MHz
PCI-X 66MHz
PCI-X 133MHz
1-2, 3-4
3-4
5-6
None
*
W1 - Power Supply Mode
Power Supply Mode
Rocker Switch Mode
ATX Mode
Power Supply always ON
(must be supported by SBC)
Jumper
4-6
2-4, 5-6
3-4
*
*
ON (autodetect)
OFF (safe mode)
ON (autodetect)
OFF (safe mode)
ON (autodetect)
OFF (safe mode)
ON (autodetect)
OFF (safe mode)
PCI/PCI-X
PCI
PCI/PCI-X
PCI/PCI-X
PCI/PCI-X
PCI/PCI-X
PCI/PCI-X
PCI/PCI-X
Bus Safe /
Auto Detect Jumper
Bus Mode Max. Speed or less
66MHz
33MHz
100/133MHz
66MHz
133MHz
100MHz
1 I/O = 133MHz
2 I/O = 100MHz
3, 4 I/O = 66MHz
66MHz
1-2
3-4
5-6
7-8
W11 - Safe / Autodetect Mode
*
*
*
*
2 6
51 W10
A93 A94
B93 B94
A1 A2
B1 B2
J24
A93 A94
B93 B94
A1 A2
B1 B2
J23
A1 A2
P1
1 2
15 16
J21
A2
B1 B2
A93 A94
B93 B94
J22
A1 A2
A93
B94
J20
A1 A2
B1 B2
A61
P2
1
W8
1
W9
1 2
19 20
J26
A93 A94
B93 B94
A1 A2
J25
4
1
J1 24
121
J3
4
1
A1 A2
J15
J4 13
1 12
24
J6
J5
13
J12
2 8 1 7
W2
1 7
W6
A1 A2 A94
B2 B94
J19
A1 A2
A93
J18
1 5 2
W1
A1 A2
A93 A94
B93 B94
J17
A1 A2
A93 A94
B94 B93
J16
Y1 Y1
U2
U2
U9 U9 U1
U1
12
1
J14
A C E G J L N
11 13 15 17
1 3 5 7 9
UR
19
W
U5
U5
J7
13
J13
DS5
DS4
DS3
DS2
DS1
J8 J11
13
Q3
13
J10
DS6
DS7
DS8
DS9
DS9
U8
U8
U7
U7
J27
2 6
51
W7
1
W5
1
W4
1
W3 U11
3 1
J31
1 3J30
10
2
1
9
J29
3
1
J28
A C J L N
11 13 15 17
1 3 5 7 9
UR
19
W
GE
U6
U6
A61
A1 A2
B1 B2
P3
Y2 Y2
75
76 51
50
25
1
100
26
U13
U13
2 8 1 7
W11
DS10
1 2J37 1 2J36 1 4
J35
24
31
W12 1
2J39 1 2J38 3 1
J40
U10
U10
1 4
J34
1 4
J33
1J32
1 2 14
13
J41
10
1 2 9
J42
0.000
1.225
4.025
7.425
0.625
0.000 0.312 1.112 1.912 2.712 3.512 4.311 5.111 5.911 6.711 7.511 8.311
9.725
6.325
11.600
8.650
0.000 2.960 6.165 8.500 5.700 4.900 3.900 3.100 0.800 3.300 0.475
0.000
0.350
3.835
3.445
7.550
8.950
10.790
7.220
6.320
6.100
MULTI-FUNCTION
HDW MONITOR
FAN1
AUX POWER+12V POWER20/24-PIN MAIN POWER
KEYBAORD
MOUSE
PWRG2
3.3V
3.3VSB
-5V
+12V
+5V
+5VSB
-12V
PWRG1
-12V +12V SPEAKER +5V NC KBDAT KBCLK -5V GND RESET GND +3.3V
FAN6
FAN3
+12V POWER
AUX POWER FAN2
+12V POWER
20/24-PIN MAIN POWER
FAN5
SPK-
SPK+
PWRG1+ PWRG2- PWRG1- PWRG2+
CI- CI+
PWRBT- PWRBT+
HDDACT-
RST- RST+
GND
+12V
SENSE
EXT. EVENT
HDDACT+
FAN4
KONTRON I.D. LABEL
SN
MADE IN CANADA
W6
BUS B
A
B
C
D
J42
1
1 111 1
1
1
J34
J35
J36
J37
J38
J39
J40
W11
1 2
7 8
J33
RST-
RST+
HDDACT-
HDDACT+
PWRBT-
PWRBT+
CI-
CI+
PWRG2-
PWRG2+
PWRG1-
PWRG1+
SPK-
SPK+
W10
126
5
J26
19 20
J22J23J24J25
J21
A1 A2 B1 B2 A1 A2 B1 B2 A1 A2 B1 B2 A1 A2 B1 B2
A93 A94 B93 B94 A93 A94 B93 B94 A93 A94 B93 B94 A93 A94 B93 B94
1
15 16
2
Slot 3 Slot 2 Slot 1 Slot 0
BUS A
BUS A
BUS B
W8
W9
GND
+12
Sense
XILINX
CPLD
XC9572XL
ConnectorsConnectors
SBC KCI System Monitor
JTAG for CPLD
Speaker
Power 1 LED
Power 2 LED
Chassis Intrusion Switch
Power ON Button
Hard Drive LED
Reset Button
External Event I/O header
ePCI-X SHB
J26
J27
J33
J34
J35
J36
J37
J38
J39
J42
P1-P3
J1
J2
J3
J4
J11
J5
J12, 13, 9
J10, 31, 40
J14
J15-20
J21
J22-25
PS/2 Mouse
PS/2 Keyboard
ATX Power Supply
+12V ATX Power Supply
+12V ATX Power Suppy (SHB)
AUX Power Supply
3-pin Fans 1-3 (with tach)
3-pin Fans 4-6 (with tach)
Kontron America I/O
3.3V PCI 64-Bit (keyed)
SHB KCI Multi-Function
5V PCI 64-Bit (keyed)
P1
P2
P3
W8, W9 - Bus A, Slot 0 Config
Standard Mode (IDSEL 31) ON OFF
When used with ePCI-200 O FF ON
& ePCI-201 (IDSEL 27)
*
W8 W9
*
12
6
5
12
6
5

TRST#
+12V
TMS
TDI
+5V
INTA#
INTC#
+5V
Reserved
+5V (I/O)
Reserved
Ground
Ground
3.3Vaux
RST#
+5V (I/O)
GNT#
Ground
PME#
AD[30]
+3.3V
AD[28]
AD[26]
Ground
AD[24]
IDSEL
+3.3V
AD[22]
AD[20]
Ground
AD[18]
AD[16]
+3.3V
FRAME#
Ground
TRDY#
Ground
STOP#
+3.3V
SMBCLK
SMBDAT
Ground
PAR
AD[15]
+3.3V
AD[13]
AD[11]
Ground
ROW B ROW A
-12V
TCK
Ground
TDO
+5V
+5V
INTB#
INTD#
PRSNT1#
Reserved
PRSNT2#
Ground
Ground
Reserved
Ground
CLK
Ground
REQ#
+5V (I/O)
AD[31]
AD[29]
Ground
AD[27]
AD[25]
+3.3V
C/BE[3]#
AD[23]
Ground
AD[21]
AD[19]
+3.3V
AD[17]
C/BE[2]#
Ground
IRDY#
+3.3V
DEVSEL#
Ground
LOCK#
PERR#
+3.3V
SERR#
+3.3V
C/BE[1]#
AD[14]
Ground
AD[12]
AD[10]
ROW B ROW A
PCI 64-BIT
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
Ground
AD[08]
AD[07]
+3.3V
AD[05]
AD[03]
Ground
AD[01]
+5V (I/O)
ACK64#
+5V
+5V
Reserved
Ground
C/BE[6]#
C/BE[4]#
Ground
AD[63]
AD[61]
+5V (I/O)
AD[59]
AD[57]
Ground
AD[55]
AD[53]
Ground
AD[51]
AD[49]
+5V I/O
AD[47]
AD[45]
Ground
AD[43]
AD[41]
Ground
AD[39]
AD[37]
+5V I/O
AD[35]
AD[33]
Ground
Reserved
Reserved
Ground
Key Area
Key Area
Connector Pinouts
1.3
QR Ver.
0Board Rev.
1
2
3
4
MOUSE:CLK
GND
MOUSE:DATA
VCC
J1 - PS/2 Mouse
1
2
3
4
KB:CLK
GND
KB:DATA
VCC
J2 - PS/2
Keyboard
J26 - SBC KCI System Monitor
GND
N.C.
N.C.
GND
GPIO1/SMBDAT
GPIO2/SMBCLK
APFLT#
CPUFLT#
EXTFLT#
GND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
FANFLT#
GND
CHASS_INT
GND
PWRATX1_FANTACH
PWRATX2_FANTACH
FAN TACH3
FAN TACH4
FAN TACH5
FAN TACH6
1
2
3
SENSE
+12V
GND
J12, 9, 13, 40, 31, 10
FANS 1-6
2
4
6
8
10
12
14
16
GND
GND
VCC
VCC
GND
GND
GND
VCC
KB:CLK
KB:DATA
VCC
SPEAKER
MOUSE:CLK
MOUSE:DATA
PBRES#
IDE:ACT#
1
3
5
7
9
11
13
15
J21 - SHB KCI Multi-Function
1
2
CHSS_INT
GND
J36 - Chassis
Intrusion Switch
1
2
PWR_BUTTON#
GND
J37 - Power ON
Button
1
2
VCC
HD:ACT#
J38 - Hard Drive
LED
1
2
3
4
GND
GND
+12V CPU
+12V CPU
J4, J11
+12ATX
J5 - Aux Power
1
2
3
GND
GND
GND
4
5
6
+3.3V
+3.3V
VCC
1
2
3
4
SPEAKER
N.C.
N.C.
VCC
J33 - Speaker
1
2
3
4
VCC
N.C.
N.C.
PWR_LED#
J35 - Power Good 2 LED
+12V
PWRBT#
+5Vaux
GND
TCK
TDI
a_PRSNT#
Reserved
+5V
a_INTA#
a_INTC#
+5V
Reserved
a_GNT3#
GND
a_GNT2#
a_GNT1#
+3.3V
a_RST#
a_GNT0#
GND
a_CLKFI
+3.3V
a_CLKD
GND
a_CLKB
+3.3V
PME#
GND
a_AD30
a_AD28
GND
a_AD26
a_AD24
+3.3V
a_AD22
a_AD20
GND
a_AD18
a_AD16
GND
a_FRAME#
a_TRDY#
+5V
a_PCIXCAP
a_STOP#
GND
SER_SDA
SER_SCL
GND
a_C/BE1#
a_AD14
+3.3V
a_AD12
a_AD10
GND
a_AD09
a_C/BE0#
GND
a_AD06
ROW B ROW A
P1 - P3 , ePCI-X SHB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
-12V
PWRGD
PSON#
TRST#
TMS
TDO
Reserved
+5V
a_INTB#
a_INTD#
+5V
+3.3Vaux
GND
Reserved
+3.3V
a_REQ3#
a_REQ2#
GND
a_REQ1#
a_REQ0#
+3.3V
a_CLKFO
GND
a_CLKC
+3.3V
a_CLKA
GND
a_AD31
a_AD29
+5V
a_AD27
a_AD25
GND
a_C/BE3#
a_AD23
GND
a_AD21
a_AD19
+5V
a_AD17
a_C/BE2#
GND
a_IRDY#
a_DEVSEL#
+3.3V
a_LOCK#
a_PERR#
+5V
a_SERR#
a_PAR
GND
a_AD15
a_AD13
GND
a_AD11
a_AD08
+5V
a_AD07
a_M66EN
RESERVED
a_AD04
+3.3V
a_AD02
a_AD00
GND
a_REQ64#
a_ACK64#
+5V
a_C/BE7#
a_C/BE6#
GND
a_PAR64
a_AD62
GND
a_AD60
a_AD58
+3.3V
a_AD56
a_AD54
GND
a_AD52
a_AD50
GND
a_AD48
a_AD46
+3.3V
a_AD44
a_AD42
GND
a_AD40
a_AD38
GND
a_AD36
a_AD34
+3.3V
a_AD32
GND
b_CLKC
GND
b_CLKA
+3.3V
b_CLKFI
GND
b_INTA#
b_INTC#
GND
b_GNT2#
b_REQ2#
+5V
b_GNT0#
b_REQ0#
GND
b_PRSNT#
b_AD30
GND
b_AD28
b_AD26
+3.3V
b_AD24
Reserved
ROW B ROW A
GND
a_AD05
a_AD03
GND
a_AD01
Reserved
+5V
Reserved
a_VIO
GND
a_C/BE5#
a_C/BE4#
+5V
a_AD63
a_AD61
GND
a_AD59
a_AD57
GND
a_AD55
a_AD53
+5V
a_AD51
a_AD49
GND
a_AD47
a_AD45
GND
a_AD43
a_AD41
+5V
a_AD39
a_AD37
GND
a_AD35
a_AD33
GND
b_CLKD
+3.3V
b_CLKB
GND
b_CLKFO
GND
b_INTB#
b_INTD#
+5V
b_GNT3#
b_REQ3#
GND
b_GNT1#
b_REQ1#
+5V
b_RST#
+5V
b_AD31
b_AD29
GND
b_AD27
b_AD25
GND
b_AD22
GND
b_AD21
b_AD20
GND
b_AD18
b_AD16
+3.3V
b_FRAME#
b_TRDY#
GND
b_PCIXCAP
b_STOP#
GND
b_PAR
b_AD15
+3.3V
b_AD13
b_AD11
GND
b_AD09
b_M66EN
GND
b_C/BE0#
b_AD06
+3.3V
b_AD04
b_AD02
GND
b_AD00
b_REQ64#
GND
b_C/BE6#
b_PAR64
+3.3V
b_AD62
b_AD60
GND
b_AD58
b_AD56
GND
b_AD54
b_AD52
+3.3V
b_AD50
b_AD48
GND
b_AD46
b_AD44
GND
b_AD42
b_AD40
+3.3V
b_AD38
b_AD36
GND
b_AD34
b_AD32
GND
Reserved
ROW B ROW A
b_VIO
b_C/BE3#
b_AD23
+5V
b_AD19
b_AD17
GND
b_C/BE2#
b_IRDY#
GND
b_DEVSEL#
+5V
b_LOCK#
b_PERR#
GND
b_SERR#
b_C/BE1#
GND
b_AD14
b_AD12
+5V
b_AD10
b_AD08
GND
b_AD07
b_AD05
GND
b_AD03
b_AD01
+5V
b_ACK64#
b_C/BE7#
GND
b_C/BE5#
b_C/BE4#
GND
b_AD63
b_AD61
+5V
b_AD59
b_AD57
GND
b_AD55
b_AD53
GND
b_AD51
b_AD49
+5V
b_AD47
b_AD45
GND
b_AD43
b_AD41
GND
b_AD39
b_AD37
+5V
b_AD35
b_AD33
GND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
Key Area
M8103_QR_0
KB:DATA
N.C.
VCC
SPEAKER
+12V
-12V
7
8
9
10
11
12
1
2
3
4
5
6
VCC3
GND
PBRST#
GND
-5V
KB:CLK
J14 - Kontron America I/O Connector
J3 - ATX Power Supply (24-pins)
13
14
15
16
17
18
19
20
21
22
23
24
1
2
3
4
5
6
7
8
9
10
11
12
VCC3
VCC3
GND
VCC
GND
VCC
GND
_
PWR OK
5VSB
12V
+12V
VCC3
VCC3
-12V
GND
_
PS ON#
GND
GND
GND
-5V
VCC
VCC
VCC
GND
_
P1 P3P2
J15-J20 3.3V Environment
TRST#
+12V
TMS
TDI
+5V
INTA#
INTC#
+5V
Reserved
+3.3V (I/O)
Reserved
3.3Vaux
RST#
+3.3V (I/O)
GNT#
Ground
PME#
AD[30]
+3.3V
AD[28]
AD[26]
Ground
AD[24]
IDSEL
+3.3V
AD[22]
AD[20]
Ground
AD[18]
AD[16]
+3.3V
FRAME#
Ground
TRDY#
Ground
STOP#
+3.3V
SMBCLK
SMBDAT
Ground
PAR
AD[15]
+3.3V
AD[13]
AD[11]
Ground
ROW B ROW A
-12V
TCK
Ground
TDO
+5V
+5V
INTB#
INTD#
PRSNT1#
Reserved
PRSNT2#
Reserved
Ground
CLK
Ground
REQ#
+3.3V (I/O)
AD[31]
AD[29]
Ground
AD[27]
AD[25]
+3.3V
C/BE[3]#
AD[23]
Ground
AD[21]
AD[19]
+3.3V
AD[17]
C/BE[2]#
Ground
IRDY#
+3.3V
DEVSEL#
PCIXCAP
LOCK#
PERR#
+3.3V
SERR#
+3.3V
C/BE[1]#
AD[14]
Ground
AD[12]
AD[10]
ROW B ROW A
Key Area
PCI 64-BIT
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
M66EN
Ground
Ground
AD[08]
AD[07]
+3.3V
AD[05]
AD[03]
Ground
AD[01]
+3.3V (I/O)
ACK64#
+5V
+5V
Reserved
Ground
C/BE[6]#
C/BE[4]#
Ground
AD[63]
AD[61]
+3.3V (I/O)
AD[59]
AD[57]
Ground
AD[55]
AD[53]
Ground
AD[51]
AD[49]
+3.3V (I/O)
AD[47]
AD[45]
Ground
AD[43]
AD[41]
Ground
AD[39]
AD[37]
+3.3V (I/O)
AD[35]
AD[33]
Ground
Reserved
Reserved
Ground
AD[09]
Ground
Ground
C/BE[0]#
+3.3V
AD[06]
AD[04]
Ground
AD[02]
AD[00]
+3.3V (I/O)
REQ64#
+5V
+5V
Ground
C/BE[7]#
C/BE[5]#
+3.3V (I/O)
PAR64
AD[62]
Ground
AD[60]
AD[58]
Ground
AD[56]
AD[54]
+3.3V (I/O)
AD[52]
AD[50]
Ground
AD[48]
AD[46]
Ground
AD[44]
AD[42]
+3.3V (I/O)
AD[40]
AD[38]
Ground
AD[36]
AD[34]
Ground
AD[32]
Reserved
Ground
Reserved
Key Area
J22-J25 5V Environment
AD[09]
C/BE[0]#
+3.3V
AD[06]
AD[04]
Ground
AD[02]
AD[00]
+5V (I/O)
REQ64#
+5V
+5V
Ground
C/BE[7]#
C/BE[5]#
+5V (I/O)
PAR64
AD[62]
Ground
AD[60]
AD[58]
Ground
AD[56]
AD[54]
+5V (I/O)
AD[52]
AD[50]
Ground
AD[48]
AD[46]
Ground
AD[44]
AD[42]
+5V I/O
AD[40]
AD[38]
Ground
AD[36]
AD[34]
Ground
AD[32]
Reserved
Ground
Reserved
J39 - RESET Button
PBRST#
GND
1
2
eBP-11A4B6eBP-11A4B6
J27 - JTAG
1
2
3
4
5
GND
TMS
JTAGEN
TCK
N.C.
6
7
8
9
10
TDI
VCC
N.C.
TDO
GND
1
2
3
4
VCC
N.C.
N.C.
PWR_LED#
J34 Power Good 1 LED
J42 - External Event
1
2
3
4
5
VCC
CPUFLT#
VCC
APFLT#
EXTFLT#
6
7
8
9
10
FANFLT#
GND
GPIO1/SMBDAT
GND
GPIO2/SMBCLK
The Quick Reference Sheet can be downloaded
from Kontron web site at:
http://www.kontron.com
or from our FTP site at:
ftp://ftp.kontron.ca/Support/
For Technical Support
please contact:
1 . Internet : www.kontron.com
2 . E-Mail : [email protected]
3. Fax : [phone]
4. Tel : [phone]
Connector PinoutsConnector Pinouts