Kozyard Caesar User manual

Assembly Manual
12’x14’ Caesar Hardtop Gazebo
With Double Roof
Kozyard LLC Products
www.kozyard.com
© Copyright 2016 - 2023 Kozyard LLC. | All Rights Reserved.
Version:20231006

12 in.
12 in.
137.8 in.
ø0.31in.
161.4 in.
.
12’x14’ Anchor Blueprint
2+
Safetyglasses
• Please read and follow this assembly and operation guide to reduce the risk of personal injury
and damage to your gazebo.
• Do not discard any of the packaging until you have checked that you have all the parts in place.
The maximum weight capacity of this gazebo roof is 2000 pounds.
• Sidewalls and nettings should be off or in the opened position and tied to poles when winds are
over 30 MPH to avoid damage.
• Some parts may have sharp edges or corners. To ensure your safety, follow basic safety precau-
tions to reduce the risk of injury. Please note that this item contains small parts which could be
swallowed by children. Keep it out of reach of children under 3 years old and pets during installa-
tion.
Warnings and Cautions
Two or more people are required
for aseembly and disassembly.
Pre-assembly
Tools that may be required.(Not included in boxes)
Note: Tools are not shown to actual size and scale.
Do not fully tighten screw prior to
complete assembly.
Recommended Min.Anchord Block size
Anchoring poles into concrete is strongly recommended.
Ensure the gazebo is positioned on level ground

page 1Caesar 12’x14’ assembly manual
A5 x4
J5 x4 J6 x4
K4 x1
L5 x4
N6 x4
D6 x2
F5 x4
K14 x1
R5 x4
F7 x2
G7 x2
E6 x2
G5 x4
H1 x4
H5 x4
H3 x1
ITEM
A5
D6
G7
F7
F5
G5
H1
J5
J6
K4
K14
L5
M1
M6
N6
R5
R
P2
Q4
Q13
Q14
P12
H3
H5
E6
DESCRIPTION
Pole 4
2
2
2
2
4
4
4
4
4
4
2
4
4
4
4
2
12
2
2
2
1
1
1
4
Beam
Beam
Beam
Beam
Joint Cover
Joint Cover
Union Bar
Roof Bar
Finishing Bar
Finishing End
Finishing Bar
Net Frame
Net Frame
Net Frame
Roof Bar Connector
Corner Cover
Plate
C
Short orner Roof Bar
C
Long orner Roof Bar
Double-sided adhesive tape
Corner Solidifyng Bar
Corner Solidifyng Bar
Inside Roof Connector
Outside Roof Connector
QTY
P2 x2
Q4 x2
P12 x2
Q14 x2
Q13 x2
R x12
M7=M1+M6
M6 x4
M1 x4
Attention: Prior to assembly, verify that all parts and pieces are included to ensure
an efficient installation process.

R11 x2
R12 x2
R13 x2
R14 x2
page 2Caesar 12’x14’ assembly manual
U3 x4
T2 x2
T4 x2
U1 x4
U6 x4
S x128+3
U4 x4
R1 x4
ITEM DESCRIPTION QTY
S
R1
R11
R12
R13
R14
T2
T4
U1
U6
U3
U4
V11
V12
V43
V44
V45
V46
B21
B22
B23
B24
B25
B26
B27
B28
4
128+3
2
2
2
2
2
2
4
4
4
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Spacer
Finishing End
Finishing Bar
Finishing Bar
Finishing Bar
Finishing Bar
Finishing Bar
Finishing Bar
Solidifying Bar
Solidifying Bar
Iron Angle
Iron Angle
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
V12 x2
V11 x2
V43 x2 V44 x2 V45 x2 V46 x2
B21 x2 B22 x2 B23 x2
B25 x2 B26 x2 B27 x2 B28 x2
B24 x2

page 3Caesar 12’x14’ assembly manual
1# x186+4
5# x80+2
6# x8+1
7# x36+2
9# x24+2
10# x4+1
11# x12+1
Allen key
Wrench
2# x16+2
3# x8+1
4# x120+2
Y3 x2
S3 x2
SY x4
S4 x2
Y4 x2
Z x76
Z2 x4
Z4 x2
Z1 x4
Z3 x2
A41 x2 A42 x2 A43 x2 A44 x2 A45 x2
A50 x2
A46 x2 A47 x2 A48 x2 A49 x2
A41
A42
A43
A44
A45
A46
A47
A48
A49
A50
S3/S4
Y3/Y4
Z
SY
Z1
Z2
Z3
Z4
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
Roof Panel
2
2
2
2
2
2
2
2
2
2
ITEM DESCRIPTION QTY
2#
1#
3#
3#L
4#
5#
6#
7#
9#
10#
11#
12#
Mosquito Net
Solid Sidewall
Strap
Bracket
Bracket
Bracket
Bracket
Bracket
Screws
Screws
Screws
Screws
Hook
Screws
Screws
Screws
Screws
Screws
Screws
Washer
4
4
4
76+2
4
4
2
2
186+4
16+2
8+1
16+2
120+2
80+2
8+1
36+2
4+1
12+1
12+2
24+2
12# x12+2
3#L x16+2D12x34/M6x12

Caesar 12’x14’ assembly manual page 4
A5 x4
L5 x4
1#
x12
Parts Required:
X12
3 inches
3/8
inches
M6
(Not included)
A5
L5
A5
L5
1#
1#
1#
X4
Step 1: Set up Poles
1. Set up Poles (Part A5) with Stand Plates (Part L5) using screws #1 as
shown in the diagram.
Reference for anchoring gazebo:
• If the ground is concrete and its depth is over 3 inches, you can purchase 3/8" diameter x 3" length
sleeve anchors.
• Only anchor after finishing all the assembly.
After assembly, we strongly recommend anchoring the gazebo to your deck or concrete as
shown above. Damage resulting from wind or improper anchoring is not covered under warranty.

page 5Caesar 12’x14’ assembly manual
X2
E6
E6 D6
E6
D6 D6
F5
F5
F5
1#
1#
1#
1#
X2
F7
F7 G7
F7
G7 G7
F5
1#
1#
1#
1#
1. Connect Beams (Part E6, D6) into one beam using Union Bar (Part F5) with
screws 1# as shown in the diagram.
2. Connect Beams (Part G7, F7) into one beam using Union Bar (Part F5) with
screws 1# as shown in the diagram.
Parts Required：
F5 x4
1#
x40
E6 x2
F7 x2 G7 x2
D6 x2
Step 2: Connect the Beams
Long Beam Overall:
Short Beam Overall:

page 6
Parts Required：
2#
x16
3#
x8
Tip:
At least three people
for this step.
3+
②
②
①
①
A5
A5
D6
E6
X8
X8
X2
X2
3#
3#L
2
2#
#
G7
F7
F7
D6
D6
A5
A5
A5
A5
D6
D6
F7
G7
G7
E6
E6
E6
E6
Caesar 12’x14’ assembly manual
3#L
x16
Step 3: Set up Poles and Beams
Use screws 3#L and 3# first, then use screw 2# to
connect Poles and Beams together as shown in
the diagram.
Tip:
Place parts on carpet or rug
to avoid scratches during
assembly.

page 7
Caesar 12’x14’ assembly manual
Parts Required: 1#
x32
J5
J5
J6
J6
J6
J6
J5
J5
J5
J6
Diagonal 1 = Diagonal 2
J5 x4 J6 x4
1# 1#
1#
Diagonal 1
Diagonal 2
Step 4: Connect Solidifying Bars wtih Beams and Poles
Affix the frame with Corner Solidifying Bars (Parts J5, J6) using screws 1# as shown
in the diagram.
Tip:
Measure (DIAGONALLY) from posts to posts
to assure alignment so all materials fit as
planned.

X4
①②
page 8
Caesar12’x14’ assembly manual
Parts Required: 9#
9#
9#
9#
x24
X4
G5 x4
G5
H5
H5 x4
①
①
①
①
②
②②
②
Step 5: Cover the connections
1. Finish Connecting Beams using
Corner Covers (Part G5) and screws 9#
as shown in the diagram.
2. Affix middle beams using Joint
Cover (Part H5) and screws 9# as
shown in the diagram.

X2 X2
X4
page 9Caesar 12’x14’ assembly manual
Parts Required:
H1 x4
4# x120
1#
4#
4#
4#
H1
4#
4#
x7
x7
x8 x8
E6 F7 G7 D6
H1 H1
H5
1#
x4
①
①
②
②
Step 6: Install Hooks
After finishing Hooks (Part 4#) into the
tracks, then put Joint Cover (Part H1) to
lock them.
Note the
amount of
hooks for
each slot
as noted
below:
Attach 7 Hooks in each slot of the Sidewall
Track on Beams (Part E6, D6).
Attach 8 Hooks in each slot of the Sidewall
Track on Beams (Part F7, G7).

page 10Caesar 12’x14’ assembly manual
K4 x1
Tip:
Parts Required:
M6
M7=M1+M6
1#
x12
1#
12#
1#
12#
M1
M6 x4
M1 x4
M1
M6
12#
x12
X4
K4
M7
M7 M7
M7
P2 P2
Q4
Q4
Upward View
②
Upward View
Step 7: Connect Corner Roof Bar “M7”
Connect the Short Corner Roof Bar (Part M1) with
Long Corner Roof Bar (Part M6) using screws 1# and
washer 12#.
Tip:
The combination will be called “Part M7” in following
steps.
Step 8: Set up Roof Frame

page 11Caesar 12’x14’ assembly manual
M7
1#
M7
M7
M7
Parts Required:
P2
P2 Q4
K4
Q4
1#
R
M7
②
②
③
③
M7 x4
R x4
1#
x20
X4 X4
X4
M7
K4
M7
M7
M7
1#
P2 x2
Q4 x2
1. Connect the Inner Roof Connector (Part K4) with the Corner Roof Bar (Part M7) using screws 1#.
2. Attach Corner Roof Bar(Part M7)
to main frame using screw 1#
as shown in the diagram.
3. Attach Finishing Bar (Part P2, Q4) with
Finish End (Part R) using screws 1# to
Corner Roof Bar (Part M7) as shown
in the diagram.

page 12Caesar 12’x14” assembly manual
1#
x20
Parts Required:
N6
N6
N6
N6
N6
N6
R5
N6
N6
N6
N6
N6
1#
1#
1#
1#
Upward View
X4
X4
X4
Q4
Q4
P2
P2
P2
N
N
1#
1#
1#
1#
1#
1#
1#
Q
P
R5 x4
N6 x4
Step 9: Set up Roof Bar
1. Attach Roof Bar (Part N6) to
Roof Connector (Part K4) using
screw 1# as shwon in the diagram.
2. Connect Roof Bar
connector (Part R5)
to Roof Bar (Part N6)
using screw 1# as
shwon in the
diagram.
3. Attach Roof Bar (Part N6) to Beams using
screw 1# as shwon in the diagram.

page 13Caesar 12’x14’ assembly manual
Parts Required:
K14 x1 1#
x2
K14 K4
1#
1#
K14
Tips: Do not tighten these two screws completely before step 12,
only after puting all upper panels in place,then tighten them thoroughly.
Upward View
Step 10: Connect Outside Roof Connctor
Connect Outside Roof Connector (Part K14) to Inside Roof (Part K4) using screw
1# as shown in the diagram.

page 14Caesar 12’x14’ assembly manual
Snap brackets (Part Z,Z1,Z2,Z3,Z4) to roof panel edges as shown in the diagram.
(with snaps facing upwards)
V11 V12 V43
Z3
Z4
V44 V45 V46
X2
Parts Required:
V11
V43
Z4
Z
Z Z
Z
Z
Z
Z3
Z1
Z1 Z2
Z2
V44 V45 V46
V12
H3 x1
Step 11: Snap Brackets
Tips:
1. Wearing protective gloves is recommended.
2. To prevent Z-Clips (plastic brackets) from sliding off prior to assembly, apply
double-sided adhesive tape (Part H3) to the underside (bottom) edge of the roof
panels where the brackets (Part Z, Z1, Z2, Z3, Z4) are supposed to attach.
3. You can use super glue (not included) to attach the brackets to the roof panel if
the double-sided tape doesn't work for you.

page 15Caesar 12’x14’ assembly manual
Parts Required:
T2
T4
T2
T4
R
1#
1#
1#
V11 V12
T2
1#
V43 V44 V45 V46
T4 1#
R
1#
RR
R
1#
x8
R x4
T4 x2
T2 x2
V11
V11
V
12
V
12
V43
V43
V44
V44
V45
V45
V46
V46
Step 12: Assemble Roof Panels
1. Push the Roof Panels (Part V11, V12, V43, V44, V45, V46)to upper roof as shown in the diagram.
2. Attach Finishing Bars (Part T2, T4) to upper roof with Finish End (Part R) using screws 1#
as shown in the diagram.

page 16
Caesar 12’x14’ assembly manual
Parts Required:
U1
U1
U1
U1
U6
U6
U6
U6
①
①
①
②
②
1#
x24
U6 x4
U1 x4
U4 x4
U3 x4
U3
U4
1#
1#
X4 X4
Step 13: Connect Solidifying Bars
Attach Solidifying Bars ( Part U1, U6) to roof bar or corner roof bar using Iron Angle (Part U3, U4)
and screws 1# as shown in the diagram.
Attention:
If the holes on the Solidifying Bar (Part U1,U6)
and the hole of the roof panel cannot be aligned,
please adjust or loosen screw 1# until the screws
of the roof panel are in place.

Caesar 12’x14’ assembly manual page 17
X2
x32
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Parts Required:
Step 14:Snap Bracket
B21 x2 B22 x2 B23 x2 B24 x2 B25 x2 B26 x2 B27 x2 B28 x2
B21 B22 B23 B24
B25 B26 B27 B28
Z
H3 x1
Tips:
Snap brackets (Part Z) to roof panel edges as shown in diagram.
(with snaps facing upwards)
1. Wearing protective gloves is recommended.
2. To prevent Z-Clips (plastic brackets) from sliding off prior to assembly, apply
double-sided adhesive tape (Part H3) to the underside (bottom) edge of the roof
panels where the brackets (Part Z) are supposed to attach.
3. You can use super glue (not included) to attach the brackets to the roof panel if
the double-sided tape doesn't work for you.

Alexander 12’X14’ assembly manual
Parts Required:
A41 A42 A43 A44 A45
A46 A47 A48 A49 A50
Step 15: Snap Bracket
A41 x2 A42 x2 A43 x2 A44 x2 A45 x2 A46 x2 A47 x2 A48 x2 A49 x2 A50 x2
X2
page 18
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
H3 x1
Z X32
Tips:
Snap bracket (Part Z) to roof panel edges as shown in diagram.
(with snaps facing upwards)
1. Wearing protective gloves is recommended.
2. To prevent Z-Clips (plastic brackets) from sliding off prior to assembly, apply double-sided adhesive tape
(Part H3) to the underside (bottom) edge of the roof panels where the brackets (Part Z) are supposed to
attach.
3. You can use super glue (not included) to attach the brackets to the roof panel if the double-sided tape
doesn't work for you.