Kozyard Odessey User manual

Assembly Manual
Kozyard LLC Products
10’x12’ Odyssey Permanent Gazebo
with Double Roof
Copyright 2016 - 2019 Kozyard LLC. | All Rights Reserved.

3. Wearing protective gloves is
recommended.
4. You may need a safety hat.
6. Please use a Phillips screwdriver.
8. For ease of construction, you may
need to use a drill.
2. You will need one or more step ladders.
5. Use the hex keys included in the box.
2+ 1. Two or more people are required
for assembly.
7. Do not fully tighten screws until
assembly is completed.
Odyssey 10x12' ANCHOR BLUEPRINT
353m/11.6'
15cm/5.9"
30x30cm/11.8"x11.8"
289cm/9.5' 259cm/8.5'
323cm/10.6'

POLE BEAM
BEAM BEAM
BEAM CORNER ROOF BAR
ROOF BAR FINISHING BAR
FINISHING BAR FINISHING BAR
FINISHING BAR FINISHING BAR
FINISHING BAR FINISHING BAR
SOLIDIFYING BAR
ROOF BAR

FINISHING BAR
FINISHING BAR PLATE
CORNER
COVER
SUPPORTING
PA RT
SUPPORTING
PA RT
FINISHING
END
PANELS PANELS
PANELS
PANELS
PANELS PANELS PANELS
PANELS PANELS PANELS
FINISHING
END
FINISHING
END
JOINT
COVER
INSIDE ROOF
CONNECTOR
OUTSIDE ROOF
CONNECTOR
FINISHING BAR
SOLIDIFYING BAR
CORNER
SOLIDIFYING BAR
CORNER
SOLIDIFYING BAR
SOLIDIFYING BAR

Step 1:
Set up poles (Part A) with plates (Part B)
using screws #1 as shown in diagram.
PANELS
158
8x
17
6
12
M6 16
M6
15
M6
HOOK PLASTIC
LOCK
SOLID
SIDEWALL
MOSQUITO
SIDEWALL JOINT COVER SCREWS SCREWS
SCREWS
SCREWS SCREWS ALLEN KEY
12
6

Step 2: Connect Part C and C1 into one beam using screws #1
as shown in diagram.
Connect Part C2 and C3 into one beam using screws #1 as shown
in diagram.
C2
1
C
C3
C3
61x
S4
1
C2
116x
M6x
C3 2x
C2 2x C1
C1 2x
1
C
C2x
C1
12

Step 3: Use screws #1, #2 and #3 to connect poles and beams
as shown in diagram.
2
3
1
6
2
16x
8x
3 3
6

Step 4: Affix the frame with corner solidifying bars
(Part L and L1) by using screws #1 as shown in
diagram.
6
12

AA x4
X
x104
①
①
①
②
②
②
AA AA
x6 x6 x6 x6 x7 x7 x7 x7
Put 6 hooks to each slot of
sidewall track (Part C and Part C1)
Put 7 hooks to each slot of
sidewall track (Part C2 and Part C3)
Step 5, After you finish putting the
hooks into the tracks, secure
part AA using screws #5.
This locks the hooks into place.
CC2 C3
C1
Step 5：
M5x10
4x

Step 6: Finish connecting beams using corner covers
(Part M) and screws #4 as shown in diagram.
Affix middle beams using joint cover (Part N) and screws
#4 and #5 as shown in diagram.
5
4
4
4
4
5

Step 8:
Connect the inside roof
connector (Part Q) with the
corner roof bar (Part D)
using screws #1 as shown in
diagram.
Affix the supporting part (Part P)
to the corner roof bar using
screws #1
Set up roof frame.
Step 7:
Attach the corner roof bar
(Part D) and main frame using
screws #1 as show in diagram.
12
12
6
6

Step 9:
Attach Roof Bars (Part E) to inside roof connector and
main beam using Screws 1#&2# as shown in diagram.
6
2
2
M6x12

Step 10:
Connect the outside roof
connector (Part Q1) to
inside roof (Part Q)
using screw #2 as
shown in diagram.
Affix finishing bars (Part F, F1 and F2) to roof bars (Part D & E) using fnishing
end (Part R and R1) and screws #1 and #2 as shown in diagram.
M6x12
10x
3x2
6
M6x16
2
2
2

Insert panels (Part T,T1 and T2) into the slots of roof bars as shown
in diagram.
Step 12:
Affix finshing bars (Parts G, G1 and G2) to roof bars
(Part E and D) using finishing end (Part R and R2) and screw #1
as shown in diagram.
Step 11:
M6x12
6

Step 13: Affix roof bars (Parts H and H1) to beam using
supporting part (Part S) and screws #1 as shown in diagram.
Insert roof bars (Part H and H1) to the slot of corner roof bar
(Part D) as shown in diagram.
M6x12
6

Step 14: Affix solidifying bars (Parts J and J1) to corner
roof bar (Part D) using screw #1 as shown in diagram.
Affix solidifying bars (Parts J and J2) to roof bar (Part E)
using screw 1# as shown in diagram.
M6x12
6

20x
Y
UV1
W
VU1
V3
2xW1
U1
V1 V2 V
V3W1
V2
V2
2xW V
U
V3 V1
U1
V3 V2W1
4x
V2
4xV3 U1 V1 UVW
4xV1
U
V1
4xV
U1
4xU1 V
U
U1
V1
V
V3
W1
V2
W
4x
U
Start from V and install piece by piece in a clockwise sequence. Only
W and W1 can joinly insert into the slot. Fit V2 and V3 from top to
the slot.
Attention:
Overall Roof Assembly

Step 15:
E
15
20x
2x
Y
W1
W
V1
WV
E
W1
V3
W1V2
2x
4x
4x
4x
4x
4x
4x
V2
W
V3
V1
V
U1
U
V
E
H
V2
V
U
E
D
Y
V3
V2
V3
W1V2
V1WV
1. Insert V into the slot of H and E, then put
V2 from above to the slot and join with V.
Connection between V and V2,V1and V3,Wand W1
Join W1 and W, then insert
into the slot of E
2. Only after the sheet metal fits well
into the slot, then install part Y to
fix it.

Step 16:
Affix finishing bars (Parts K, K1 and K2) to
roof bars using finishing end (Part R and R2)
and screws as shown in diagram.
M6X12
4
6
4

Step 17 : Hang up solid sidewall as shown in diagram.
Z
Z
ZZ Z
Z
Z
Z
Z