Kozyard KZF606 User manual

Outdoor 3pcs Rocking
Chair Set
Assembly Manual
Kozyard LLC Products
www.kozyard.com
© Copyright 2016 - 2023 Kozyard LLC. | All Rights Reserved.
Version:20231006
• Prior to assembly, ensure that you lay out and identify all
the parts listed in the parts list.
• Tighten all nuts and bolts securely. Hand-tighten all bolts
before use. Avoid using power tools or applying excessive
force during assembly and bolt tightening.
• If you encounter any difficulties during assembly or if any
part is missing or damaged, please don't hesitate to
contact our customer service team via email at
[e-mail] or by calling our toll-free number at
866-355-0018.
• The weight capacity of this chair is 250 lbs.
• Clean the frame components and fabric with a mild soap
solution, then rinse thoroughly. Avoid using bleach, acid,
or any other solvents on either the fabric or frame compo-
nents.
• For a comprehensive warranty policy, please visit
www.kozyard.com. Be aware that warranty terms can
change without prior notification.
• For the best performance and safety of your chair, inspect
and tighten all bolts and fasteners regularly
Assembly Instructions
Care and warranty

Chair
Left Leg
Right Leg
M6*16
M6*30
Seat
Back
Cap
Screw
Screw
Washer
1
1
1
1
12
6
6
12
F
G
H
A
B
C
D
E
Description Qty
Part
Screw
driver
Seat
Cushion
Back
Cushion
1
1
1
I
J
K
Description Qty
Part
Part list

B
E
E
C
G
F
H
H
A
B
C
A
Reminder: All parts must be placed on
carpet during assembly.
!Don’t fully tighten all screws
until Final step.
1. Attach the Left Leg (Part A) and Right Leg (Part B) to
the Seat (Part C) using Screws (G), Washers (H), and
Caps (E) as illustrated in the diagram.
2. Attach the Left Leg (Part A) and Right Leg (Part B) to
the Seat (Part C) using Screws (F), Washer (H), and Cap
(E) as depicted in the diagram.

E
D D
G
H
Reminder: All parts must be placed on
carpet during assembly.
E
F
H
3. Assemble the Back (Part D) with Legs (Parts A and B)
using Screws (G), Washers (H), and Caps (E) as illustrat-
ed in the diagram.
4. Assemble the Back (Part D) with Legs (Parts A and B)
using Screws (F), Washers (H), and Cap (E) as shown in
the diagram.

5. Position the Back Cushion (Part K) and Seat Cushion
(Part J) on the chair.
K
J
To p
Glass
M6*16
M6*22
Connector
Leg
Cap
Screw
Screw
Washer
1
1
1
4
12
4
8
12
F1
G1
H
A1
B1
C1
D1
E
Description Qty
Part
Tighten and check all screws before using
on level ground.
Repeat for other rocking chair.
Part list Table

Reminder: All parts must be placed on
carpet during assembly.
E1 D1
A1
C1
F1
H
D1
E
H
G1
!Don’t fully tighten all screws
until Final step.
1. Assemble Leg (Part D1) with Top (Part A1) using
Screw (F1), Washer (H), and Cap (E).
2. Connect Connector (Part C1) with Leg (Part D1) using
Screw (G1), Washer (H), and Cap (E)

B1
Ensure that all screws are securely tightened
and inspect them before use on level ground.
3. Place Glass (Part B1) on top.
866-355-0018
© Copyright 2016 - 2023 Kozyard LLC. | All Rights Reserved.
Kozyard LLC