Kozyard Outdoor 4pcs Conversation Set KZF601GR User manual

Assembly Instrucions
Outdoor 4pcs Conversation Set
Kozyard LLC Products
WWW.KOZYARD.COM
© Copyright 2016 - 2020 Kozyard LLC. | All Rights Reserved.
Prior to assembly, make sure you lay out and identify all the parts listed
in the parts list below.
Tighten all nuts and bolts securely. All bolts should be hand tightened
before use. Never use power tools or excessive force during assembly
or for tightening of bolts.
ASSEMBLY INSTRUCTIONS
Should you experience any difficulty during assembly or if any parts are
missing or damaged:
Contact our customer service by email: [email protected] or call toll
free: 866-355-0018.
Warning:
1. Make sure the conversation set is placed on a solid, level surface.

Part
Part List
Hardware Bag
A
B
C
D
E
F
H
I
J
K
L*8
M6*20 M6*32 M6*42 M6*60
Q*54 R*1 S*1
M*2 N*18 O*12
P*6
G
Description Description Qty Qty
Part
6
2
1
2
1
4
1
1
2
1
4
Leg
Single Seat
Double Seat
Connecting bar
Connecting bar
Supporting bar
Supporting bar
Back Frame
TableTop Frame
Table Leg
Top Glass

1. Place legs (Part A) together by connecting bar
(Part D) using bolt N and washer Q.
Then affix the two connect bars (Part G) to legs
(Part A) separately by using bolt N,and washer Q.
Attention: Leave the above hole for
connecting seat later.
(Please see Step 3 and Step 4)
Single Chair
！Don’t screw thoroughly until Step 5.

2. Attach supporting bar (Part F) under seat
(Part B) as show in diagram.
！
！
Do not skip this step,It is critical to fit
Part F before the next step.
3.Place single seat (Part B) on legs (Part A) using
bolt O, washer Q, plastic washer P ,and nut as shown
in diagram.
Attention:
Plastic washer (Part P) must be
placed between Part A and Part B.
O
O
Don’t screw thoroughly until
Step 5 as shown in diagram
0.2”
Back hole

5.
6.Repeat steps 1 to 5 for the other
single chair.
Once finished, tighten all nuts and bolts
securely before use.
4. Attach other side of seat (Part B) to leg (Part A)
using bolt O,plastic washer P, washer Q ,and nut
as shown in diagram.
Attention: Part P must be placed
between Part A and Part B.
！Don’t screw thoroughly
until Step 5.
0.2”

1. First, set up legs (Part A) by connecting bar (Part E) using
bolt N and washer Q. Then attach back frame (Part H) to legs
(Part A) using bolt N and washer Q as shown in diagram.
Attention: Leave the above hole for
connecting seat later.
(Please see Step 4)
Loveseat
！
Don’t screw thoroughly until Step 5.

！Do not skip this step,It is critical to fit
Part F before next step.
3. Attach the double seat (Part C) to back frame (Part H) and
connecting bar (Part E) using bolt M, washer Q and nut as
shown in diagram.
2.Attach supporting bar (Part F) under seat
(Part C) as show in diagram.
！Don’t screw thoroughly
until Step 5
0.2”
Back hole

4.Attach double seat (Part C) to legs (Part A) using
bolt O, washer Q, plastic washer P ,and nut as shown
in diagram.
5. Once finished, tighten all nuts and bolts securely
before use.
Attention: Plastic washer (Part P) must be put between
Part A and Part C.
！Don’t screw thoroughly
until Step 5 .
0.2”

1. Attach table legs (Part J) to the table top frame (Part I)
using bolt L and washer Q as shown in diagram.
Coffee Table

2.
3.
Put glass (Part K) on (Part I) as shown in diagram.
Once finished, tighten all nuts and bolts securely
before use.
Kozyard LLC
10808 6th ST, Unit 100,
Rancho Cucamonga, CA 91730
66