Kramer DIP-20 User manual

DIP-20 Quick Start
P/N:
2900- 301071QS
Rev:
9
Scan for full manual
DIP-20 Quick Start Guide
This guide helps you install and use your DIP-20 for the first time.
Go to www.kramerav.com/downloads/DIP-20 to download the latest user manual and check if firmware
upgrades are available.
Step 1: Check what’s in the box
DIP-20 Automatic Video Switcher
1 Bracket set
4 Rubber feet
1 Power adapter (48V)
1 Quick start guide
Step 2: Mount DIP-20
Install DIP-20 using one of the following methods:
•Attach the rubber feet and place the unit on a flat surface.
•Fasten a bracket (included) on each side of the unit and attach it to a flat surface
(see www.kramerav.com/downloads/DIP-20).
•Mount the unit in a rack using the recommended rack adapter
(see www.kramerav.com/product/DIP-20).
•Ensure that the environment (e.g., maximum ambient temperature &
air flow) is compatible for the device.
•Avoid uneven mechanical loading.
•Appropriate consideration of equipment nameplate ratings should be
used for avoiding overloading of the circuits.
•Reliable earthing of rack-mounted equipment should be maintained.
•Maximum mounting height for the device is 2 meters.
Step 3: Connect inputs and outputs
Always switch OFF the power on each device before connecting it to your DIP-20. For best results, we recommend that you
always use Kramer high-performance cables to connect AV equipment to the DIP-20.

Step 4: Set DIP-switches
Video Switching Selection
DIP-switch 1 DIP-switch 2 Video Input Selection
DIP-switch 1
DIP-switch 2
Video Input Selection
Off (up)
Off (up)
Automatic—Last connected. Where more than one source is
connected the last one connected has priority
Off (up)
On (down)
Automatic—Priority selection.
HDMI 1 →HDMI 2 →PC IN (default, high to low priority)
On (down)
Off (up)
Manual
On (down)
On (down)
Manual
Audio Switching Selection
DIP-switch 3
DIP-switch 4
Audio Input Selection
Off (up)
Off (up)
Automatic—Priority selection.
Embedded HDMI™→analog Audio In (high to low priority)
Off (up)
On (down)
Automatic—Priority selection.
Analog Audio In →embedded HDMI (high to low priority)
On (down)
Off (up)
Embedded HDMI
On (down)
On (down)
Analog Audio In
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
Step 5: Connect power
Connect the power cord to DIP-20 and plug it into the mains electricity.
Safety Instructions (See www.kramerav.com for updated safety information)
Caution:
•For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual.
•There are no operator serviceable parts inside the unit.
Warning:
•Use only the power cord that is supplied with the unit.
•Disconnect the power and unplug the unit from the wall before installing.
Step 6: Operate DIP-20
Default IP Parameters
Parameter
Values
Default
Device Name
Any alphanumeric string up to 14 chars (can include hyphen, but not at the beginning or end)
KRAMER_
DHCP
ON/OFF
OFF
IP Address
Any valid IP address
192.168.1.39
Mask
Any valid network mask
255.255.0.0
Gateway
Any valid gateway address
192.168.0.1
TCP Port
0 to 65535
5000
UDP Port
0 to 65535
50000
Default RS-232 Communication Parameters
Parameter
Values
Baud Rate
115200
Data Bits
1
Stop Bits
1
Parity
None
Command Format
ASCII
Default Web Pages Logon Authentication
Parameter
Values
Name
Admin
Password
Admin
You can operate the DIP-20 via the front panel buttons, remote P3000 commands, or by using a Web browser to access the
built in Web pages.