Kramer WP-580Txr User manual

WP-580TXR, WP-580RXR Quick Start
P/N:
2900- 301255QS
Rev:
2
Scan for full manual
WP-580TXR, WP-580RXR Quick Start Guide
This guide helps you install and use your WP-580TXR, WP-580RXR for the first time.
Go to www.kramerav.com/downloads/WP-580TXR to download the latestuser manual and check if
firmware upgrades are available.
Step 1: Check what’s in the box
WP-580Txr HDMI Line Transmitter
1 5V DC Power adapter (for each device)
WP-580Rxr HDMI Line Receiver
1 Quick start guide
Step 2: Get to know your WP-580TXR, WP-580RXR
WP-580Txr
(US and US-D Sizes):
WP-580Txr
(European Size):
#
Feature
Function
1
HDMI™IN Connector
Connects to the HDMI source.
2
ON LED
Lights red when receiving power only, orange when either input or output and
power are attached, and green when both an active input and output are
attached.
Note,if no input is connected, the device invokes the power save mode
automatically turning off the power.
3
HDBT OUT/LINE OUT RJ-45 Connector
Connects to the HDBT IN/LINE IN RJ-45 connector on the WP-580Rxr.
4
5V DC
+5V DC connector for powering the unit.
5
PROG 4-pin Connector
For internal use.
6
Grounding Screw
Connect to grounding wire.
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.

WP-580Rxr
(US and US-D Sizes):
WP-580Rxr
(European Size):
#
Feature
Function
1
HDMI OUT Connector
Connects to the HDMI acceptor.
2
ON LED
Lights red when receiving power only, orange when either input or output and power are
attached, and green when both an active input and output are attached. Note, if no input
is connected the device invokes the power save mode automatically turning off the
power.
3
HDBT IN/LINE IN RJ-45 Connector
Connects to the HDBT OUT/LINE OUT RJ-45 connector on the WP-580Txr.
4
+5V DC
+5V DC connector for powering the unit.
5
PROGRAM 4-pin Connector
For internal use.
6
XR Jumper
For providing extra transmitter-receiver range:
With the Jumper: a range of up to 150 meters (490 feet) at 1080p@60Hz@24bpp
Without the Jumper: A range of up to 100 meters (330 feet) at 1080p@60Hz@36bpp
7
Grounding Screw
Connect to grounding wire.
Step 3: Mount WP-580TXR, WP-580RXR
Connect the TP cable between the WP-580Txr and WP-580Rxr and then mount them in suitable wall boxes.
Step 4: Connect inputs and outputs
Always switch OFF the power on each device before connecting it to your WP-580TXR, WP-580RXR.
Wiring the RJ 45 Connectors
This section defines the TP pinout, using
a straight pin-to-pin cable with RJ 45
connectors.
EIA /TIA 568B
PIN
Wire Color
1
Orange / White
2
Orange
3
Green / White
For HDBT cables, it is recommended
that the cable ground shielding be
connected/soldered to the connector
shield.
4
Blue
5
Blue / White
6
Green
7
Brown / White
8
Brown
To achieve specified extension distances, use the recommended Kramer cables available at www.kramerav.com/product/WP-580TXR.
Using third-party cables may cause damage!
Step 5: Connect power
Connect the power cord to WP-580TXR, WP-580RXR and plug it into the mains electricity.
Safety Instructions (See www.kramerav.com for updated safety information)
Caution:
•For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual.
•There are no operator serviceable parts inside the unit.
Warning:
•Use only the power cord that is supplied with the unit.
•Disconnect the power and unplug the unit from the wall before installing.