KROHNE H250 M9 Wiring diagram

Variable area flowmeter
Device category II2G with electrical internals
H250 M9
H250 M9H250 M9
H250 M9 Supplementary instructions
Supplementary instructionsSupplementary instructions
Supplementary instructions
© KROHNE 03/2013 - 4002553501 MA H250/M9-NEPSI Ex i AD R01 en
AD_H250_M9_NEPSI_Ex_ia_R01_en_4002553501_PRT.book Page 1 Thursday, March 7, 2013 7:31 AM

CONTENTS
2 www.krohne.com 03/2013 - 4002553501 MA H250/M9-NEPSI Ex i AD R01 en
H250 M9
1 Safety instructions 3
1.1 General notes ................................................................................................................... 3
1.2 NEPSI conformity ............................................................................................................. 3
1.3 Security information......................................................................................................... 3
2 Device description 4
2.1 Device description ............................................................................................................ 4
2.2 Description code............................................................................................................... 4
2.3 Marking............................................................................................................................. 5
2.4 Flammable products ........................................................................................................ 6
2.5 Device category ................................................................................................................ 6
2.6 Types of protection ........................................................................................................... 6
2.7 Ambient temperature / temperature classes.................................................................. 7
2.8 Electrical data................................................................................................................. 11
3 Installation 12
3.1 Installation...................................................................................................................... 12
4 Electrical connections 13
4.1 General notes ................................................................................................................. 13
4.2 Power supply .................................................................................................................. 13
4.3 Inputs/outputs ................................................................................................................ 13
4.4 Earthing and equipotential bonding............................................................................... 13
5 Operation 14
5.1 Start-up........................................................................................................................... 14
5.2 Operation ........................................................................................................................ 14
6 Service 15
6.1 Maintenance ................................................................................................................... 15
6.2 Dismantling .................................................................................................................... 15
7 Attachment 16
8 Notes 21
AD_H250_M9_NEPSI_Ex_ia_R01_en_4002553501_PRT.book Page 2 Thursday, March 7, 2013 7:31 AM

SAFETY INSTRUCTIONS 1
3
H250 M9
www.krohne.com03/2013 - 4002553501 MA H250/M9-NEPSI Ex i AD R01 en
Safety instructions
1.1 General notes
These additional instructions apply to explosion-protected versions of variable area flowmeters
with electrical built-ins and the marking Ex ia IIC T1 - T6 Gb. They complete the installation and
operation instructions for the non-explosion protected versions.
The information given in these instructions contains only the data relevant to category 2
explosion protection. The technical details given in the installation and operation instructions for
the non-explosion protected versions apply unchanged unless excluded or superseded by these
instructions.
1.2 NEPSI conformity
The H250/../M9... variable-area flowmeters series has been approved by NEPSI (National
Supervision and Inspection Center for Explosion Protection and Safety of Intrumentation in
China) under Certification No.
This certification together with its boundary conditions is required to be observed without fail
(see also Attachment "Certificate").
The Ex marking is NOT acc. to the ATEX directive 94/9/EC. Placing the product on the market of
the EU for purpose of distribution and/or use in the EU is NOT permitted.
1.3 Security information
Assembly, installation, start-up and maintenance may only be performed by personnel trained in
explosion protection!
GYJ12.1130
GYJ12.1130GYJ12.1130
GYJ12.1130
CAUTION!
The operator respectively his agent is responsible to follow further standards, directives or laws
if required due to operating conditions or place of installation. This applies particularly for the
use of easy detachable process connections such as SMS or Clamp when measuring flammable
mediums.
AD_H250_M9_NEPSI_Ex_ia_R01_en_4002553501_PRT.book Page 3 Thursday, March 7, 2013 7:31 AM

2DEVICE DESCRIPTION
4
H250 M9
www.krohne.com 03/2013 - 4002553501 MA H250/M9-NEPSI Ex i AD R01 en
Device description
2.1 Device description
Variable area flowmeters measure and display the volume flow of flammable and non-
flammable gases and liquids. Depending on the device version, electrical limit switch contacts
and a 4...20 mA signal output or a Profibus PA interface can be installed in the display.
2.2 Description code
The safety description code * consists of the following elements:
* positions which are not needed are omitted (no blank positions)
1 Direction of flow
H - horizontal orientation
U - vertical downwards
no identifier - standard upwards
2 Materials / versions
RR - Stainless steel
C - PTFE or PTFE/ceramics
HC - Hastelloy
Ti - Titanium
F - Sterile version (food)
3 Heating jacket version
B - with heating jacket
4 Indicator part series
M9 - Indicator M9 standard indicator
M9S - Indicator with increased protection
M9R - Indicator in stainless steel housing
M9T - Indicator in stainless steel housing with increased protection
5 High-temperature version
HT version with HT extension
6 Electrical signal output
ESK - Electronic transmitter
7 Limit switch
K1 - One limit switch
K2 - Two limit switches
8 Explosion protection
Ex - Explosion-protected equipment
AD_H250_M9_NEPSI_Ex_ia_R01_en_4002553501_PRT.book Page 4 Thursday, March 7, 2013 7:31 AM

DEVICE DESCRIPTION 2
5
H250 M9
www.krohne.com03/2013 - 4002553501 MA H250/M9-NEPSI Ex i AD R01 en
2.3 Marking
Type designation of the complete unit is shown on the indicator with the nameplates reproduced
below (see also description code).
Additional markings on the housing cover:
•SN - serial number
•SO - sales order / item
•PA - order
•Vxxx - product configurator code
•AC - article code
Additional plate
The association of the housing cover to the device is confirmed by an additional plate with the
serial number on the interior of the indicator part.
1 Device type
2 Manufacturer
3 Sizing data: temperature & pressure rating
4 PED data
5 Ex data
6 Electrical connection data
7 Note on observing documentation
8 Manufacturer's website
AD_H250_M9_NEPSI_Ex_ia_R01_en_4002553501_PRT.book Page 5 Thursday, March 7, 2013 7:31 AM

2DEVICE DESCRIPTION
6
H250 M9
www.krohne.com 03/2013 - 4002553501 MA H250/M9-NEPSI Ex i AD R01 en
2.4 Flammable products
Atmospheric conditions:
Atmospheric conditions:Atmospheric conditions:
Atmospheric conditions:
An explosive atmosphere is a mixture of air and flammable gases, vapours, mists or dusts under
atmospheric conditions. The following values define it
Tatm = -20...+60°C / -4...+140°F and Patm = 0.8...1.1 bar.
Outside of this range, no key data are available as to ignition behaviour for most mixtures.
Installation conditions:
Installation conditions:Installation conditions:
Installation conditions:
Variable area flowmeters operate outside of atmospheric conditions, which means that
explosion protection –regardless of the zone assignment –is fundamentally not applicable due
to the lack of key safety data for the interior of the measuring section.
2.5 Device category
Variable area flowmeters are designed according to GB 3836.1-2010 and GB 3836.4-2010
2.6 Types of protection
The variable area flowmeter is designed with protection type intrinsic safety, protection level
"ia".
WARNING!
Operation with flammable products is only permitted as long as no explosive fuel/air mixture
builds up on the inside of the flowmeter under operating conditions. The operator is responsible
for ensuring that the flowmeter is operated safely as regards the temperature and pressure of
the products used. In case of operation with flammable products the measuring units must be
included in the periodic pressure tests of the system. When using the device version H250/C...
(PTFE-liner, nonconductive) the min. conductivity of the medium must be 10
-8
S/m, in order to
avoid the electrostatic charge.
The marking Ex ia IIC T1 - T6 GB contains the following information:
The marking Ex ia IIC T1 - T6 GB contains the following information:The marking Ex ia IIC T1 - T6 GB contains the following information:
The marking Ex ia IIC T1 - T6 GB contains the following information:
Ex ia
Ex iaEx ia
Ex ia Intrinsically safe, protection level "ia"
IIC
IICIIC
IIC Suitable for gas groups IIC, IIB and IIA
T1 - T6
T1 - T6T1 - T6
T1 - T6 Suitable for temperature classes T6 ... T1
Gb
GbGb
Gb EPL, suitable for zone 1
AD_H250_M9_NEPSI_Ex_ia_R01_en_4002553501_PRT.book Page 6 Thursday, March 7, 2013 7:31 AM

DEVICE DESCRIPTION 2
7
H250 M9
www.krohne.com03/2013 - 4002553501 MA H250/M9-NEPSI Ex i AD R01 en
2.7 Ambient temperature / temperature classes
Due to the influence of the product temperature, variable area flowmeters with built-in electrical
equipment (electric variants) are not assigned to any fixed temperature class. The temperature
class of these devices is rather a function of the product temperature and ambient temperature
that is present and the specific device version. Please see the following tables for the
assignments.
The tables take into account the following parameters:
•Installed equipment
•Maximum values Iiand Pifor K1, K2
•Ambient temperature Tamb.
•Product temperature Tm
•Nominal size DN
•Standard or high temperature version (HT)
•Standard or heating jacket version
•Heat resistance of the connecting cable
When there is more than type of built-in equipment, the data of the most unfavourable
equipment should be used.
For certain device version, lower values apply due to differing boundary conditions (e.g. lining
materials). Here the user should consult the technical data sheet.
INFORMATION!
The maximum permissible product temperatures listed in the tables are valid under
the following conditions:
• The measuring device is installed and operated in accordance with the installation
instructions in the standard documentation.
• It must be ensured that the flowmeter is not heated by the effects of additional
heat radiation (sunshine, neighbouring system components) and
thus operated above the permissible ambient temperature range.
• Insulation must be limited to the piping.
Unobstructed ventilation of the indicator part must be ensured.
To do this, the variant with a projecting indicator (HT version) is preferable.
• For device versions with a heating jacket, that the temperature of the heating medium does
not exceed the maximum permissible product temperature.
AD_H250_M9_NEPSI_Ex_ia_R01_en_4002553501_PRT.book Page 7 Thursday, March 7, 2013 7:31 AM

2DEVICE DESCRIPTION
8
H250 M9
www.krohne.com 03/2013 - 4002553501 MA H250/M9-NEPSI Ex i AD R01 en
Using a heat resistant connecting cable
1Maximum value of the product temperature for the use of a standard connecting cable. For
higher product temperatures a connecting cable with a temperature resistance of 100°C / 212°F
is required.
HT version - high-temperature version with projecting indicator
The permitted ambient temperature range is indicated on the nameplate.
Ambient temperatures
The minimum product temperature is -40°C / -40°F.
Temperature table in °C
Heating jacket Tm1
none with HT-version Tamb ≤40 Tamb ≤60
DN15, DN25 DN15 -150
x - 236
DN50 DN25 -127
x - 171
DN80, DN100 DN50, DN80 -109
x - 145
Temperature table in °F
Heating jacket Tm1
none with HT-version Tamb ≤104 Tamb ≤140
DN15, DN25 DN15 -302
x - 456
DN50 DN25 -260
x - 340
DN80, DN100 DN50, DN80 -228
x - 293
Version Tamb.
°C°F
ESK2A, ESK3-PA -40...+60 -40...+140
SJ3,5-SN / I7S23,5 -40...+60 -40...+140
SC3,5-N0 / SJ3,5-S1N -25...+60 -13...+140
AD_H250_M9_NEPSI_Ex_ia_R01_en_4002553501_PRT.book Page 8 Thursday, March 7, 2013 7:31 AM

DEVICE DESCRIPTION 2
9
H250 M9
www.krohne.com03/2013 - 4002553501 MA H250/M9-NEPSI Ex i AD R01 en
Maximum permitted product temperature in
Maximum permitted product temperature inMaximum permitted product temperature in
Maximum permitted product temperature in °C
CC
C
Maximum permitted product temperature Tm[°C]
Heating jacket TK T6 T5 T4 T3 T2, T1
without with HT
version
Tamb
[°C] 
≤40 ≤60 ≤60 ≤40 ≤60 ≤40 ≤60
ESK II and ESK2A
ESK II and ESK2AESK II and ESK2A
ESK II and ESK2A
DN15,
DN25 DN15 85 100 135 200 183 200 183
x85 100 135 200 200 300 300
DN50 DN25 85 100 135 200 165 200 165
x85 100 135 200 200 300 300
DN80,
DN100 DN50, DN80 85 100 135 200 150 200 150
x85 100 135 200 200 300 252
ESK3-PA
ESK3-PAESK3-PA
ESK3-PA
DN15,
DN25 DN15 83 76 135 200 183 200 183
x85 100 135 200 200 300 300
DN50 DN25 77 74 135 200 165 200 165
x85 91 135 200 200 300 300
DN80,
DN100 DN50, DN80 71 72 135 200 150 200 150
x85 85 135 200 200 300 252
K1/K2 - 64 mW
K1/K2 - 64 mWK1/K2 - 64 mW
K1/K2 - 64 mW
DN15,
DN25 DN15 85 100 135 200 200 200 200
x85 100 135 200 200 300 300
DN50 DN25 85 100 135 200 200 200 200
x85 100 135 200 200 300 300
DN80,
DN100 DN50, DN80 85 100 135 200 200 200 200
x85 100 135 200 200 300 300
K1/K2 (I7S23,5-N / SC3,5-N0) - 169 mW
K1/K2 (I7S23,5-N / SC3,5-N0) - 169 mWK1/K2 (I7S23,5-N / SC3,5-N0) - 169 mW
K1/K2 (I7S23,5-N / SC3,5-N0) - 169 mW
DN15,
DN25 DN15 not admissi
ble
not
admissi
ble
135 200 156 200 156
x135 200 200 300 300
DN50 DN25 135 200 141 200 141
x135 200 200 300 239
DN80,
DN100 DN50, DN80 125 200 125 200 125
x135 200 192 300 192
K1/K2 (SJ3,5-SN and SJ3,5-S1N) - 169 mW
K1/K2 (SJ3,5-SN and SJ3,5-S1N) - 169 mWK1/K2 (SJ3,5-SN and SJ3,5-S1N) - 169 mW
K1/K2 (SJ3,5-SN and SJ3,5-S1N) - 169 mW
DN15,
DN25 DN15 62 100 135 200 200 200 200
x85 100 135 200 200 300 300
DN50 DN25 59 100 135 200 200 200 200
x81 100 135 200 200 300 300
DN80,
DN100 DN50, DN80 55 100 135 200 195 200 195
x70 100 135 200 200 300 300
AD_H250_M9_NEPSI_Ex_ia_R01_en_4002553501_PRT.book Page 9 Thursday, March 7, 2013 7:31 AM

2DEVICE DESCRIPTION
10
H250 M9
www.krohne.com 03/2013 - 4002553501 MA H250/M9-NEPSI Ex i AD R01 en
Maximum permitted product temperature in
Maximum permitted product temperature inMaximum permitted product temperature in
Maximum permitted product temperature in °F
FF
F
Maximum permitted product temperature Tm[°F]
Heating jacket TK T6 T5 T4 T3 T2, T1
without with HT
version
Tamb
[°F] 
≤104 ≤140 ≤140 ≤104 ≤140 ≤104 ≤140
ESK II and ESK2A
ESK II and ESK2AESK II and ESK2A
ESK II and ESK2A
DN15,
DN25 DN15 185 212 275 392 361 392 361
x185 212 275 392 392 572 572
DN50 DN25 185 212 275 392 329 392 329
x185 212 275 392 392 572 572
DN80,
DN100 DN50, DN80 185 212 275 392 302 392 302
x185 212 275 392 392 572 485
ESK3-PA
ESK3-PAESK3-PA
ESK3-PA
DN15,
DN25 DN15 181 169 275 392 361 392 361
x185 212 275 392 392 572 572
DN50 DN25 170 165 275 392 329 392 329
x185 196 275 392 392 572 572
DN80,
DN100 DN50, DN80 160 161 275 392 302 392 302
x185 185 275 392 392 572 485
K1/K2 - 64 mW
K1/K2 - 64 mWK1/K2 - 64 mW
K1/K2 - 64 mW
DN15,
DN25 DN15 185 212 275 392 392 392 392
x185 212 275 392 392 572 572
DN50 DN25 185 212 275 392 392 392 392
x185 212 275 392 392 572 572
DN80,
DN100 DN50, DN80 185 212 275 392 392 392 392
x185 212 275 392 392 572 572
K1/K2 (I7S23,5-N / SC3,5-N0) - 169 mW
K1/K2 (I7S23,5-N / SC3,5-N0) - 169 mWK1/K2 (I7S23,5-N / SC3,5-N0) - 169 mW
K1/K2 (I7S23,5-N / SC3,5-N0) - 169 mW
DN15,
DN25 DN15 not admissi
ble
not
admissi
ble
275 392 313 392 313
x275 392 392 572 572
DN50 DN25 275 392 286 392 286
x275 392 392 572 462
DN80,
DN100 DN50, DN80 275 392 257 392 257
x275 392 377 572 377
K1/K2 (SJ3,5-SN and SJ3,5-S1N) - 169 mW
K1/K2 (SJ3,5-SN and SJ3,5-S1N) - 169 mWK1/K2 (SJ3,5-SN and SJ3,5-S1N) - 169 mW
K1/K2 (SJ3,5-SN and SJ3,5-S1N) - 169 mW
DN15,
DN25 DN15 143 212 275 392 392 392 392
x185 212 275 392 392 572 572
DN50 DN25 138 212 275 392 392 392 392
x178 212 275 392 392 572 572
DN80,
DN100 DN50, DN80 131 212 275 392 383 392 383
x158 212 275 392 392 572 572
AD_H250_M9_NEPSI_Ex_ia_R01_en_4002553501_PRT.book Page 10 Thursday, March 7, 2013 7:31 AM

DEVICE DESCRIPTION 2
11
H250 M9
www.krohne.com03/2013 - 4002553501 MA H250/M9-NEPSI Ex i AD R01 en
2.8 Electrical data
Built-in equipment for the variable area flowmeter may only be connected to separate
intrinsically safe circuits with the following maximum values:
Electrical equipment Nominal voltage Nominal current
Limit switch K1 / K2 8VDC 1...3 mA
Signal output ESK II and ESK2A 24 VDC ±25% 4...20 mA with HART®communication
ESK3-PA Profibus transmitter 1 9...24 VDC 12 mA
1Further information and instructions for operation of the ESK3-PA Profibus transmitter are provided in separate sup-
plementary instructions.
Maximum values
Built-in equipment Ui[V] Ii[mA] Pi[mW] Ci[nF] Li[μH]
ESKII / ESK2A 30 100 1000 20 ~ 0
ESK3-PA 1 24 380 5320 ~ 0 ~ 0
I7S23,5-N
SC3,5-N0 16 25 64 150 150
16 52 169 150 150
SJ3.5-SN
SJ3.5-S1N 16 25 64 30 100
16 52 169 30 100
1FISCO Field device
AD_H250_M9_NEPSI_Ex_ia_R01_en_4002553501_PRT.book Page 11 Thursday, March 7, 2013 7:31 AM

3INSTALLATION
12
H250 M9
www.krohne.com 03/2013 - 4002553501 MA H250/M9-NEPSI Ex i AD R01 en
Installation
3.1 Installation
Installation and setup must be carried out according to the applicable installation standards by
qualified personnel trained in explosion protection.
Variable area flowmeters must be installed in such a way that
•There is no danger from mechanical impact effects.
•There are no external forces affecting the indicator part.
•The device is accessible for any visual inspections that are necessary, and can be viewed from
all sides.
•The nameplate is clearly visible.
•It can be operated from a location with secure footing.
Take special note of the installation position for the H250/H/... with horizontal flow
direction:
In order to comply with thermal parameters and measuring accuracy, flowmeters for horizontal
installation are to be installed in the pipeline so that the display is located on the side of the
measuring tube. The maximum product and ambient temperatures indicated as well as the
measuring accuracy are based on lateral installation of the display.
CAUTION!
The manufacturer is not liable for any damage resulting from improper use or use for other than
the intended purpose. This applies in particular to hazards due to insufficient corrosion
resistance and suitability of the materials in contact with product.
AD_H250_M9_NEPSI_Ex_ia_R01_en_4002553501_PRT.book Page 12 Thursday, March 7, 2013 7:31 AM

ELECTRICAL CONNECTIONS 4
13
H250 M9
www.krohne.com03/2013 - 4002553501 MA H250/M9-NEPSI Ex i AD R01 en
Electrical connections
4.1 General notes
The connecting cables should be selected according to the applicable installation standards and
the maximum operating temperature. The outside diameter of the connecting cables must be
matched to the sealing area of the conduit entry/entries. The connecting cables must be laid and
fastened securely in such a way that they are adequately protected against damage.
All cores that are not used must be securely connected to the earth potential of the hazardous
area or carefully insulated against each other and against earth (test voltage ≥500 Veff).
In order to comply with thermal parameters and measuring accuracy, flowmeters for horizontal
installation are to be installed in the pipeline so that the display is located on the side of the
measuring tube. The maximum product and ambient temperatures indicated as well as the
measuring accuracy are based on lateral installation of the display.
Cable entries / Blanking plugs
The variable area flowmeter is equipped with two blanking plugs as standard. These elements
guarantee protection from foreign bodies and water (protection type) IP65 as per EN 60529. The
cable entries provided also ensure protection from foreign bodies and water. The nominal
diameter range of the cable entries is 5...10 mm. Suitable blanking plugs are to be used for
unused cable entries. Ensure that the seals are tight.
4.2 Power supply
The variable area flowmeter does not require a separate power supply. The required supply for
the built-in electronics is provided via the 4...20mA current output.
4.3 Inputs/outputs
The terminal assignment of the built-in electrical equipment is described in the Standard
Installation and Operation Instructions. The variable area flowmeter signal circuits may only be
connected to certified intrinsically safe slave units or circuits. For more information see chapter
"Electrical data"
4.4 Earthing and equipotential bonding
If the device is not sufficiently electrostatically grounded via the process cables, an additional
earth connection must be established using the ground terminal. The ground terminal on the
back of the display guarantees an electrostatic connection of the device and does not comply
with the requirements of an equipotential bonding connection.
Shields should be securely connected to the earth potential of the hazardous area, and
connected to the terminal located in the indicator part via the shortest route. In the case of shield
earthing at both ends (e.g. for reasons of electromagnetic compatibility), adequate equipotential
bonding that reliably prevents potential differences is necessary between the two earthed ends
of the shield in order to avoid excessive equalising current.
AD_H250_M9_NEPSI_Ex_ia_R01_en_4002553501_PRT.book Page 13 Thursday, March 7, 2013 7:31 AM

5OPERATION
14
H250 M9
www.krohne.com 03/2013 - 4002553501 MA H250/M9-NEPSI Ex i AD R01 en
Operation
5.1 Start-up
Start-up is only permitted when the variable-area flowmeter:
•is correctly installed in the system and connected.
•has been checked for the proper state with regard to its installation and connection
requirements.
The user of the system must be have it checked before start-up in compliance with the national
regulations for checks before start-up.
5.2 Operation
Variable area flowmeters must be operated in such a way that they remain within the maximum
and minimum permissible temperatures and pressures and the electrical limit values.
Variable area flowmeters may only be operated if the equipment parts necessary for safety are
effective in the long run, and are not rendered inoperable during operation.
Adjusting the limit switch during operation is permitted. To do so, remove the housing cover.
Close the housing cover immediately after adjusting the limit switch.
For more information see chapter "Dismantling"
CAUTION!
Potential risks of sparking caused by pressure surges, external impacts or friction must be
avoided especially for Titanium measuring cones.
AD_H250_M9_NEPSI_Ex_ia_R01_en_4002553501_PRT.book Page 14 Thursday, March 7, 2013 7:31 AM

SERVICE 6
15
H250 M9
www.krohne.com03/2013 - 4002553501 MA H250/M9-NEPSI Ex i AD R01 en
Service
6.1 Maintenance
Maintenance work of a safety-relevant nature within the meaning of explosion protection may
only be carried out by the manufacturer, his authorised representative or under the supervision
of authorised inspectors.
To maintain proper condition, regular inspections are required for systems in hazardous areas.
The following checks are recommended:
•Checking the housing, the cable entries and the feed lines for corrosion and/or damage.
•Checking the measuring unit and the piping connections for leakage.
•Checking the measuring unit and the indicator for dust deposits.
•Including the flowmeter in the regular pressure test of the process line.
6.2 Dismantling
Exchanging the built-in equipment
Due to the modular structure of the variable area flowmeters, from a safety point of view it is
possible to exchange the electrical equipment built into the indicator for identical spare parts.
To do this, remove the housing cover. The housing cover must be closed immediately after the
spare parts are exchanged. Make sure that the cover seal is properly seated. The fastening
screws of the housing cover should be tightened with a torque of 1.2 Nm.
Exchanging the entire device
Removal and installation is the user's responsibility.
Before disconnecting the electric connecting cable of the device, it must be ensured that all of
the cables leading to the indicator part are de-energised relative to each other and to the
reference potential of the hazardous area. This also applies to functional earthing conductors
(FE) and equipotential bonding conductors (PA).
CAUTION!
Avoid electrostatic charges when cleaning the surfaces (e.g. sight window).
CAUTION!
There may be a loss of measuring accuracy!
CAUTION!
• Pressurized pipes must be depressurized before removing the measuring section.
• In the case of environmentally critical or hazardous products, appropriate safety precautions
must be taken with regard to residual liquids in the measuring unit.
• New seals must be used when re-installing the device in the piping.
AD_H250_M9_NEPSI_Ex_ia_R01_en_4002553501_PRT.book Page 15 Thursday, March 7, 2013 7:31 AM

7ATTACHMENT
16
H250 M9
www.krohne.com 03/2013 - 4002553501 MA H250/M9-NEPSI Ex i AD R01 en
Attachment
AD_H250_M9_NEPSI_Ex_ia_R01_en_4002553501_PRT.book Page 16 Thursday, March 7, 2013 7:31 AM

ATTACHMENT 7
17
H250 M9
www.krohne.com03/2013 - 4002553501 MA H250/M9-NEPSI Ex i AD R01 en
AD_H250_M9_NEPSI_Ex_ia_R01_en_4002553501_PRT.book Page 17 Thursday, March 7, 2013 7:31 AM

7ATTACHMENT
18
H250 M9
www.krohne.com 03/2013 - 4002553501 MA H250/M9-NEPSI Ex i AD R01 en
AD_H250_M9_NEPSI_Ex_ia_R01_en_4002553501_PRT.book Page 18 Thursday, March 7, 2013 7:31 AM

ATTACHMENT 7
19
H250 M9
www.krohne.com03/2013 - 4002553501 MA H250/M9-NEPSI Ex i AD R01 en
AD_H250_M9_NEPSI_Ex_ia_R01_en_4002553501_PRT.book Page 19 Thursday, March 7, 2013 7:31 AM

7ATTACHMENT
20
H250 M9
www.krohne.com 03/2013 - 4002553501 MA H250/M9-NEPSI Ex i AD R01 en
AD_H250_M9_NEPSI_Ex_ia_R01_en_4002553501_PRT.book Page 20 Thursday, March 7, 2013 7:31 AM