Kurgo Back Seat Barrier Installation manual

Installation
and care
OR
Attaching the barrier: Detachable Headrests
1. Orient the barrier so the
Kurgo logo is facing the
back of the car. Remove the
driver’s seat headrest. Slide
the inner headrest column
through the large inner
elastic loop (A). Slide the
outer D-ring (B)
through
outer headrest post. Repeat
on passenger side.
2. OPTION A - Clip hook (C)
to the underside of the front
seat base plate or springs.
OPTION B - Run strap (F)
around the outside footing
of each seat and secure
hook (C).
3. Pull top straps (D) tight
on both sides; pull both
bottom straps (F) tight.
8.10 For more information: 877.847.3868 :: www.kurgo.com :: [email protected]
Passenger Seat
Center Console
View from backseat
INSTALLED VIEW
Cup Holder
Pockets
Optional extra support for barrier extension:
Flip up orange Velcro (G) and slide metal rod (H) through
slot (I) that runs across the top of the barrier between
the vertical bar pockets (J). Close and secure Velcro (G).
To lower barrier extension:
1) Open velcro (G) on the left and right side, and remove
the metal bar found in each slot (J), also remove metal rod (H).
2) Roll mesh top from bar slot (I) down and tuck fabric
into large black pocket
Parts List & Key:
Ainner elastic loop
Bouter D-ring
Cunder seat hook
Dtop headrest strap
Etop tension buckle
Funder seat strap
Gsteel support velcro closure
Hhorizontal steel support rod
Isteel support rod pocket
Jvertical steel support bar pocket
For an online video demonstration of how to install the Backseat
Barrier visit us at: www.kurgostore.com/pages/instructions.html
Become a fan of Kurgo on
Facebook and receive all the latest
updates, giveaways and contests.

Fixed Headrests
1. Pull top headrest strap
(D) out of its buckle (E).
2. Wrap strap (D) around the headrest. Insert strap
through the large loop (A) of the inner elastic strap.
Bring the strap back around the headrest and
run through (E). Repeat on opposite headrest.
CONTINUE FROM STEP TWO
OF THE DETACHABLE
HEADREST INSTRUCTIONS
Washing instructions
•Brush off loose dirt with a dry brush.
•As needed, wipe off with a dampsponge and mild soap.
•Rinse only, if possible. Use cold water and a sponge or rinse in a tub withoutsoap.
•Machine wash in front-loading unit (DO NOTuse machine with agitator, agitator could cause damage not
covered under warranty) Remove metal bars before washing. Use cold water and mild soap (Ivory Flakes,
Woolite, Sport Wash, Etc.)Notdetergents.
•Rinse thoroughly to eliminate soapresidue.
•Lay flat to dry.
8.10 For more information: 877.847.3868 :: www.kurgo.com :: [email protected]
Passenger Seat
Center Console
View from backseat
INSTALLED VIEW
Cup Holder
Pockets
TRAINING:
1) Get your dog familiar with riding in the car, focusing
on the back seats and not the front. Before setting out
on a long road trip with this new product, take some
shorter trips to help Fido become adjusted to the barrier.
2) Most importantly, the understanding of basic
obedience really makes the difference on any car ride.
Make sure your pup has a grasp of sit, stay and come to
help create easy going excursions.
Parts List & Key:
Ainner elastic loop
Bouter D-ring
Cunder seat hook
Dtop headrest strap
Etop tension buckle
Funder seat strap
Gsteel support velcro closure
Hhorizontal steel support rod
Isteel support rod pocket
Jvertical steel support bar pocket