KVM-TEC MATRIXLINE Original operating instructions

kvm-tec
First Aid
Mouse glide & switch
Video error
(stripes in the
picture)
USB is not
working
No Power
(No LED)
Check the
powerplug
Is the power
supply ok? Try
another Unit.
Try reprogramming
the Unit by using a
JTAG programmer
Contact kvm-tec
support
Are the USB
Devices plugged
in correctly?
Is the USB cable
on the Local side
plugged into the
PC?
Are the USB
Devices working
directly on the
PC?
Check if local
and remote Unit
have the same
fi rmware
Replace the USB
cable from PC to
the Local
Extender
Check if the local
or the remote
Unit is causing
the problem by
swaping fi rst the
local and than the
remote Unit to
another Unit
Contact kvm-tec
support
Check if all
cables are plug-
ged in correctly
Check if the PC is
sending a Image by
plugging in a
monitor on the
local out of the
local Unit
Check if the DDC is
set correctly (in menu
under point „O“)
Check if both
Units have the
correct fi rmware
No Video
Contact kvm-tec
support
Check if all
cables are plug-
ged in correctly
Check if the PC is
sending a Image
by plugging in a
monitor on the
local out of the
local Unit
Check if local and re-
mote Unit have the
correct fi rmware
Check if the DDC
is set correctly (in
the menu under
point „o“)
Check if the
network switch
is setup correctly
and has enough
bandwidth
Contact kvm-tec
support
Check if other units
have the same
behaviour
We are here for you to answer
your questions about installation?
Manual download www.kvm-tec.com
or
kvm-tec Installationchannel on our homepage
personally [phone]
kvm-tec Support [email protected] Phone: [phone] - 30
www.kvm-tec.com
kvm-tec
Quick
Installation
Check out
our Installation Channel:
connect collaborate communicate control
kvm-tec = C 4
Softwarefeature
for
MATRIXLINE and
4K Ultraline
Mouse Glide
&
Switch

matrixline
RS232
matrixline
RS232
matrixline
RS232
matrixline
RS232
matrixline
RS232
matrixline
RS232
matrixline
RS232
matrixline
RS232
Audio to PC Audio to PC
Audio to PC Audio to PC
USB to PC
USB to PC
USB to PC
USB from PC
DVI in from PC
Audio
from PC Audio
from PC Audio
from PC
Audio
from PC
DVI in from PC
DVI in from PC
DVI in from PC
DVI from Monitor
Audio from microphone
Audio to
speaker
USB from
keyboard and mouse
DVI to Monitor DVI to Monitor
DVI to Monitor
power plug
12V 1A
power plug
12V 1A power plug
12V 1A
power plug
12V 1A
power plug
12V 1A
power plug
12V 1A
power plug
12V 1A
power plug
12V 1A
Network cable CAT 5e/6/7 up to 150m/492ft
Quick Installation mouse glide&switch local / CPU – remote/ CON
1. Connect the MX CON/Remote and MX Local Units to the supplied 12V 1A power supply.
2. Now connect the USB cables to a USB jack on your PCs and connect the other ends of the USB
cables to the CPU/Local Units Connect the Keyboards and mouse to the CON/Remote Units.
3. Connect the MX CPU/Local and the CON/Remote Unit with several network cables to the
switch.
4. Connect the DVI cables from the PCs to the DVI/in jacks of the MX Local devices and connect
the MX Remote devices to the DVI cables of the monitors.
5. Then connect to the PCs audio-out with multiple audio cables to Local Audio in. Then connect
the speaker via the audio cables Remote Audio/out
6. Almost there! Now use multiple audio cables to connect Local Audio/out to PC´s Audio/in and
Remote Audio/into the audio cables to the microphones.
MUCH FUN - your mouse glide&switch is now ready and you can now work quite smoothly!