Kwikset 907 15 SMT User manual

19701 DaVinci
Lake Forest, CA 92610
1-800-327-5625
www.kwikset.com
A Black & Decker Company
Printed in the USA
Touchpad Electronic Deadbolt
Installation & Learning Instructions
Owner’s Manual
Copyright © 2010 Kwikset Corporation
Part No: 40486 / 02

Table of Contents
Enclosed Pieces Page 1
1 Door Preparation Page 2
2 Deadbolt Latch Installation Page 2
3 Strike Installation Page 3
4 Touchpad Electronic Deadbolt Installation Page 4
5 Programming Instructions Page 6
6 Proper Operation of Touchpad Electronic Deadbolt Page 7
Notes and Warranty Page 8
Troubleshooting Tips Page 9

A
B
C
D
E
F
G
H
I
1
Pieces
Touchpad
Latch
Strike
Keys
Deadbolt
Mounting Plate
Power Strip
Power Board
Access Cover
Important Notes:
Use the components from this
package, make no substitutions.
Consult local building codes for
requirements in your area.
Read all instructions and lay out
parts as shown.
Under normal use it is recom-
mended to replace the batteries in
the Power Board once a year.
AB
C
D E F
G
H
T-TURN
I
Enclosed Pieces

2. Deadbolt Latch Installation (Piece B)1. Door Preparation
Replacement Installation
Remove all old lock
components.
Use the enclosed template
to verify the following:
Deadbolt face hole needs to
be 2-1/8” (54mm) diameter.
Backset – Distance from
edge of door to center of
lock (2-3/8 or 2-3/4”).
Location to drill the small starter holes for
inside and outside trims.
Make any necessary modifications.
First-time Installation
Follow instructions on enclosed template.
Preparation for latch with Face Plate
Keeping edges parallel to the face of the door,
outline face plate and remove deadbolt latch
(see illustration below left).
Chisel outline of face plate until it is flush with
door edge, 5/32” (4mm) deep (see illustration
below right).
With bolt extended, insert deadbolt latch in
edge hole. Be sure to keep the word "UP" at
top. Secure with two 5/8” wood screws.
Install Latch
1
2
1
1
2
•
•
•
•
2
For latch with face plate:
To Adjust Backset:
Rotate to a 2-3/4” (70mm)
position, if required.
UP

2. Deadbolt Latch Installation (Piece B) 3. Strike Installation (Piece C)
With bolt retracted, insert deadbolt latch into
edge hole keeping flat edge of bolt parallel to
the edge of door. Be sure to keep the word
"UP" at top.
Using a wood block, tap with hammer until
surface of collar is flush with door edge
Re-extend bolt.
First-time Installation
Draw a horizontal centerline across the door
jamb, the same distance from floor as is the
centerline of deadbolt latch.
Measure back from door stop, 1/2 the
distance of the door thickness and draw a
vertical centerline. At crosspoint, drill a 1-1/8”
diameter (28.5mm) hole,1-1/4” (29mm) deep,
in the door jamb.
Center strike over hole and trace around
strike. Chisel out door frame until strike is
flush.
Position strike with large holes toward door
stop. Pre-drill large holes 3” (76mm) deep.
Important Note:
Deadbolt latch must enter strike
with no resistance or the Power-
bolt Touchpad Electronic Deadbolt
will not work properly.
1
2
1
2
3
U P
3
4
Door
Jamb
1/2 of door
thickness
Door
Stop
For Drive-In latch:
Install strike
Install 3” (76mm) screws in large strike holes
and install remaining 5/8” wood screws in
smaller holes.
Close door and ensure bolt extends and
retracts freely.
1
2

4. Touchpad Electronic Deadbolt Installation
With bolt of latch in the extended position,
place Touchpad Aon outside of door and
place power strip Gthrough door over top
of latch B. Note: Do not remove backing
from Touchpad.
With key removed, place deadbolt Eagainst
Touchpad A with round of torque blade at top
to enter through crank of latch B.
Attach deadbolt with 2 large black bolts
through mounting plate Fas shown. Power
strip Gshould extend out.
123
4
Line Touchpad Aup with small holes from
template and attach with two 1” oval head
screws. Do not over-tighten screws.
4
Round
Crank

4. Touchpad Electronic Deadbolt Installation
Feed power strip Gthrough large square hole
of Power Board Hand plug into the 6 prongs.
Line Power Board Hup to the 3 small holes
drilled from the template. Verify that torque
blade engages with the T-turn and attach
power board with 3 chrome-colored screws.
5
Remove access cover I from Power Board H.
Hold as shown in photo and twist or pull up
on cover.
5 6 7 Install 4 new AA Alkaline batteries (not
included in package). Battery positions shown
on battery case. A series of quick beeps will
sound when batteries make complete contact.
Low Battery Indicator Light on the Power
Board will be lit when the batteries need to be
replaced.
Do not dispose of in fire, recharge, put in
backwards, disassemble, mix with used or
other battery types. May explode or leak and
cause personal injury.
8

4. Touchpad Electronic Deadbolt Installation 5. Programming Instructions
Push program button on Power Board H once.1
6
2
3
Retract deadbolt latch Bwith T-turn. Press the lock button on Touchpad A. If motor runs but
latch does not extend: Door handing needs to be changed. To change door handing, remove
jumper (located in the upper right corner of the circuit board) from position "A" and plug it into
position "B". See illustrations.
9
Verify key works in deadbolt E.
Note: When manually locking or unlocking the deadbolt by turning the key or the T-turn:
The motion will be rm — this resistance is normal.
Enter desired 4 to 8 digit code by pressing
numbers on outer Touchpad A. Press the
Lock button on Touchpad to set your code.
You will hear a 2-second long beep when your
code is accepted.
If unit does not
beep — too much
time has elapsed
between steps
1 and 2. Repeat
steps 1 and 2
faster.
10
From Exterior:
If hinge is on the left, you
have a left hand door.
If hinge on the right, you
have a right hand door.
Exterior
Right hand
Door
Left hand
Door
•
•

5. Programming Instructions 6. Proper Operation of Touchpad Electronic Deadbolt
7
To Enter Second Code
Push program button twice, then repeat steps
2-4.
5Push the Lock button on outside touch pad to
extend latch bolt 1” which locks the door when
you leave.
Enter your desired personal code to retract
the latch bolt completely which unlocks the
door when you return home.
The T-turn on the inside of the door is used to
extend (lock) or retract (unlock) the latch bolt
when you are inside.
Using the key from the outside will also extend
(lock) or retract (unlock) the latch bolt.
This Touchpad Electronic Deadbolt should be
accompanied by a Kwikset Knobset, Leverset,
or Handleset.
1
2
3
4
5
Enter your number to verify that it retracts
the latch B.
4Snap access cover I onto power board H.
Align cover to top of power board and press
down at the bottom of the cover (see illustra-
tion below). To coordinate with your home
decorating scheme, the access cover may
be painted to
match your
door.
CAUTION: Prevent unauthorized
entry. This lock can be opened
using two different codes that are randomly
set at the factory. Upon installation and
set-up, replace both of these codes with
your own. Since anyone with access to the
power board can change these codes, you
must restrict access to the power board
and routinely check both codes to assure
they have not been altered without your
knowledge.

Important — Please Read Warranty Manufacture's note.
8
Under normal use it is recommended to
replace the batteries once a year. When
batteries are low, it will take longer to retract
the bolt. Batteries should be changed im-
mediately!
Lower latch must hold shut allowing deadbolt
latch to enter strike freely with no restrictions.
If door is misaligned, make necessary adjust-
ment to deadbolt strike location and/or hole
in door jamb to allow the deadbolt latch to
retract and extend freely.
Reprogramming of codes should not be
necessary after changing batteries.
If required, key can be used to retract
deadbolt.
If interior trim is exposed to extreme cold
temperatures, the batteries will not operate.
This is typical of all batteries and not a mal-
function of the lock.
•
•
•
WARNING: This Manufacturer
advises that no lock can provide complete
security by itself. This lock may be defeated
by forcible or technical means, or evaded
by entry elsewhere on the property. No lock
can substitute for caution, awareness of your
environment, and common sense. Builder’s
hardware is available in multiple performance
grades to suit the application. In order to
enhance security and reduce risk, you should
consult a qualified locksmith or other security
professional.
Full Lifetime Finish Warranty
Full Lifetime Mechanical Warranty
One Year Limited Electrical Warranty
This Warranty states all mechanical lock
parts will be free from defects in material and
workmanship, including deterioration over time
of finish on the exterior lock components while
the original purchaser owns the lock.
All electrical components are covered by a
One Year Limited Warranty.
Our warranty excludes locks that have been
damaged by installation contrary to our written
instructions or modified with non-Kwikset
components. It also excludes incidental
or consequential damages. (Some states
do not allow the exclusion or limitation of
incidental damages so this exclusion may
not apply to you.) To register a warranty
claim, please return the product, freight
prepaid to Attn: Consumer Services, Kwikset
Corporation, 19701 Da Vinci, Lake Forest,
California 92610. Kwikset will repair or replace
the lock or refund the purchase price (if it is
not practical to repair or replace). You will be
responsible for the removal of the old lock and
the installation of the new one.
This Warranty provides you with specific legal
right and you may also have other rights which
vary from state to state.