KYLAND Technology KIEN7009 Series Assembly instructions

KIEN7009/SICOM3009A/SICOM3306 Industrial Ethernet
SwitchHardware Installation Manual
Publication Date: Mar. 2015
Version: V1.1

KIEN7009/SICOM3009A/SICOM3306 Industrial Ethernet Switch
Hardware Installation Manual
Disclaimer: Kyland Technology Co., Ltd. tries to keep the content of this manual as
accurate and as updated as possible. This document is not guaranteed to be error-free, and
we reserve the right to amend it without notice to users.
All rights reserved.
No part of this documentation may be excerpted, reproduced, translated, annotated or
duplicated, in any form or by any means without the prior written permission of KYLAND
Corporation.
Copyright © 2015 Kyland Technology Co., Ltd.

Notice for Safety Operation
The product performs reliably as long as it is used according to the guidance. Artificial
damage or destruction of the device should be avoided. Before using the device, read this
notice carefully for personal and equipment safety. Please keep the manual for further
reference. Kyland is not liable to any personal or equipment damage caused by violation of
this notice.
Do not place the device near water sources or damp areas. Keep the ambient relative
humidity within the range from 5% to 95% (non-condensing).
Do not place the device in an environment with high magnetic field, strong shock, or high
temperature. Keep the working and storage temperatures within the allowed range.
Install and place the device securely and firmly.
Please keep the device clean; if necessary, wipe it with soft cotton cloth.
Do not place any irrelevant materials on the device or cables. Ensure adequate heat
dissipation and tidy cable layout without knots.
Wear antistatic gloves or take other protective measures when operating the device.
Avoid any exposed metal wires because they may be oxidized or electrified.
Install the device in accordance with related national and local regulations.
Before power-on, make sure the power supply is within the allowed range of the device.
Overhigh voltage may damage the device.
Power connectors and other connectors should be firmly interconnected.
Do not plug in or out the power supply with wet hands. When the device is powered on,
do not touch the device or any parts with wet hands.
Before operating a device connected to a power cable, remove all jewelry (such as rings,
bracelets, watches, and necklaces) or any other metal objects, because they may cause
electric shock or burns.
Do not operate the device or connect or disconnect cables during an electrical storm.
Use compatible connectors and cables. If you are not sure, contact our sales or
technical support personnel for confirmation.

Do not disassemble the device by yourself. When an anomaly occurs, contact our sales
or technical support personnel.
If any part is lost, contact our sales or technical support personnel to purchase the
substitute. Do not purchase parts from other channels.
Dispose of the device in accordance with relevant national provisions, preventing
environmental pollution.
In the following cases, please immediately shut down your power supply and contact your
Kyland representative:
Water gets into the equipment.
Equipment damage or shell damage.
Equipment operation or performance has abnormally changed.
The equipment emits odor, smoke or abnormal noise.

The following information applies when operating this device in hazardous locations:
Suitable for use in Class I, Division 2, Groups A, B, C and D Hazardous Locations, or
nonhazardous locations only.
Cet appareillage est utilisable dans les emplacements de Classe I, Division 2, Groupes A, B,
C et D, ou dans les emplacements non dangereux seulement.
WARNING: EXPLOSION HAZARD
Do not disconnect equipment while the circuit is live or unless the area is known to be
free of ignitable concentrations.
Substitution of any component may impair suitability for Class I, Division 2.
Exposure to some chemicals may degrade the sealing properties of materials used in
the following devices: Identification of the sealed devices.
AVERTISSEMENT: RISQUE D'EXPLOSION
Avant de deconnecter l'equipement, couper le courant ou s'assurer que l'emplacement
est designe non dangereux.
La substitution de composants peut rendre ce materiel inacceptable pour les
emplacements de Classe I, Division 2.

I
Contents
1 Product Overview...............................................................................................................1
2 Structure and Interface.......................................................................................................5
2.1 Front Panel ..................................................................................................................5
2.2 Top Panel.....................................................................................................................7
3 Mounting ............................................................................................................................8
3.1 Dimension Drawing (Unit: mm) ....................................................................................8
3.2 Mounting Modes and Steps .........................................................................................9
3.2.1 DIN-Rail Mounting.................................................................................................9
3.2.2 Panel Mounting....................................................................................................10
4 Cable Connection.............................................................................................................12
4.1 10/100Base-T(X) Ethernet Port..................................................................................12
4.2 100Base-FX Ethernet Port.........................................................................................13
4.3 1000Base-X, 10/100/1000Base-T(X) SFP Slot..........................................................14
4.3.1 Gigabit SFP Optical Module ................................................................................14
4.3.2 Gigabit SFP Electrical Module.............................................................................16
4.4 Console Port ..............................................................................................................16
4.5 Grounding..................................................................................................................17
4.6 Power Terminal Block................................................................................................18
4.7 Alarm Terminal Block.................................................................................................20
5 Reset................................................................................................................................22
6 LEDs ................................................................................................................................23
7 Switch Access ..................................................................................................................25
7.1 Access through Console Port.....................................................................................25
7.2 Access through Telnet ...............................................................................................27
7.3 Access through Web..................................................................................................27
8 Basic Features and Specifications ...................................................................................29

Product Overview
1
1 Product Overview
KIEN7009/SICOM3009A/SICOM3306 includes a series of green low-consumption industrial
Ethernet switches applied in the wind power, distribution network automation, subway PIS
and AFC, power SCADA, sewage treatment, highway, metallurgy, hydroelectric power,
photovoltaic generation, subway CBTC, plant automation, intelligent transportation, and
many other industries.
The series switches provide Mini USB Console port, and supports Virtual Cable Test (VCT),
one-touch recovery, and network management through Web, Telnet, and console port.
KIEN7009/SICOM3009A/SICOM3306 supports DIN rail mounting and panel mounting.
KIEN7009 and SICOM3009A provides up to six 10/100Base-T(X) Ethernet ports and three
100Base-FX/100Base-TX ports. SICOM3306 provides up to six 10/100Base-T(X) Ethernet
ports, two 100Base-FX Ethernet ports, and one 1000Base-X, 10/100/1000Base-T(X) SFP
slot. For details, see the following table.
Table 1 KIEN7009 Models
Models
SICOM3009A-Ports-Connector-PS1-PS2
Code definition
Code option
Ports: GX, S/M, T
3S6T, 3M6T, 2S6T, 2M6T, 2S4T, 2M4T, 1S7T, 1M7T, 8T
Note:
2S6T: two 100Base-FX ports, single mode; six 10/100Base-T(X) ports.
2M6T: two 100Base-FX ports, multiple mode; six 10/100Base-T(X)
ports.
Connector: parameters for
S/M
Ports with M:
ST05=ST connector, 1310nm, 5km
SC05=SC connector, 1310nm, 5km
FC05=FC connector, 1310nm, 5km
Ports with S:
ST40=ST connector, 1310nm, 40km

Product Overview
2
SC40=SC connector, 1310nm, 40km
FC40=FC connector, 1310nm, 40km
SC60=SC connector, 1310nm, 60km
SC80=SC connector, 1550nm, 80km
Ports without S or M:
N/A
PS1-PS2: power input
L2-L2 (24DCW, redundant power input, UL approved),
L5-L5(12DCW, redundant power input)
Table 2 SICOM3009A Models
Models
SICOM3009A-Ports-Connector-PS1-PS2
Code definition
Code option
Ports: GX, S/M, T
3S6T, 3M6T, 2S6T, 2M6T, 1S7T, 1M7T, 8T
Note:
2S6T: two 100Base-FX ports, single mode; six 10/100Base-T(X) ports.
2M6T: two 100Base-FX ports, multiple mode; six 10/100Base-T(X)
ports.
Connector: parameters for
S/M
Ports with M:
ST05=ST connector, 1310nm, 5km
SC05=SC connector, 1310nm, 5km
FC05=FC connector, 1310nm, 5km
Ports with S:
ST40=ST connector, 1310nm, 40km
SC40=SC connector, 1310nm, 40km
FC40=FC connector, 1310nm, 40km
SC60=SC connector, 1310nm, 60km
SC80=SC connector, 1550nm, 80km
Ports without S or M:

Product Overview
3
N/A
PS1-PS2: power input
L2-L2 (24DCW, redundant power input, UL approved),
L5-L5(12DCW, redundant power input)
Table 3 SICOM3306 Models
Models
SICOM3306-Ports-Connector-PS1-PS2
Code definition
Code option
Ports: GX, S/M, T
1GX2S6T, 1GX2M6T, 3GX6T, 2GX6T, 1GX8T
Note:
1GX2S6T: one 1000Base-X, 10/100/1000Base-T(X) SFP slot; two 100Base-FX
ports, single mode; six 10/100Base-T(X) ports.
1GX2M6T: one 1000Base-X, 10/100/1000Base-T(X) SFP slot; two 100Base-FX
ports, multiple mode; six 10/100Base-T(X) ports.
Connector:
parameters for S/M
Ports with M:
ST05=ST connector, 1310nm, 5km
SC05=SC connector, 1310nm, 5km
FC05=FC connector, 1310nm, 5km
Ports with S:
ST40=ST connector, 1310nm, 40km
SC40=SC connector, 1310nm, 40km
FC40=FC connector, 1310nm, 40km
SC60=SC connector, 1310nm, 60km
SC80=SC connector, 1550nm, 80km
Ports without S or M:
N/A
PS1-PS2: power
input
L2-L2 (24DCW, redundant power input, UL approved),
L5-L5(12DCW, redundant power input)

Product Overview
4
Note:
For the product information listed in the preceding table, we reserve the right to amend it without
notice to users. To obtain the latest information, you can contact our sales or technical support
personnel.

Structure and Interface
5
2 Structure and Interface
Caution:
To keep ports clean and ensure switch performance, you are advised to purchase the port
dustproof shield (optional).
2.1 Front Panel
Front Panel of KIEN7009-3S/M-6T and SICOM3009A-3S/M-6T
Figure 1 Front Panel of KIEN7009-3S/M-6T and SICOM3009A-3S/M-6T
Table 4 Description of the Front Panel of KIEN7009-3S/M-6T and SICOM3009A-3S/M-6T
No.
Identifier
Description
(1)
PWR1
Power 1 LED
(2)
PWR2
Power 2 LED
(3)
Run
Running LED
(4)
Ring
Ring LED
(5)
Alarm
Alarm LED
(6)
Reset
Reset button

Structure and Interface
6
(7)
Console
Console port
(8)
7-9
100Base-FX Ethernet ports
(9)
7-9
100Base-FX Ethernet port LEDs
(10)
1-6
10/100Base-T(X) Ethernet ports
(11)
--
10/100Base-T(X) Ethernet port speed LED (yellow)
(12)
--
10/100Base-T(X) Ethernet port connection status LED (green)
Front Panel of SICOM3306-1GX-2S/M-6T
Figure 2 Front Panel of SICOM3306-1GX-2S/M-6T
Table 5 Description of the Front Panel of SICOM3306-1GX-2S/M-6T
No.
Identifier
Description
(1)
PWR1
Power 1 LED
(2)
PWR2
Power 2 LED
(3)
Run
Running LED
(4)
Ring
Ring LED
(5)
Alarm
Alarm LED

Structure and Interface
7
(6)
Reset
Reset button
(7)
Console
Console port
(8)
G1
Gigabit SFP slot
(9)
G1
Gigabit SFP slot LED
(10)
7-8
100Base-FX Ethernet ports
(11)
7-8
100Base-FX Ethernet port LEDs
(12)
1-6
10/100Base-T(X) Ethernet ports
(13)
--
10/100Base-T(X) Ethernet port speed LED (yellow)
(14)
--
10/100Base-T(X) Ethernet port connection status LED (green)
2.2 Top Panel
Figure 3 Top Panel
Table 6 Description of the Top Panel
No.
Identifier
Description
1
Alarm terminal block
2
Power terminal block
3
Grounding screw

Mounting
8
3 Mounting
3.1 Dimension Drawing (Unit: mm)
Figure 4 Dimensions for DIN-rail Mounting
Figure 5 Dimensions for Panel Mounting
Caution:
The preceding figure uses SICOM3009A-3S/M-6T as an example. The other models of
KIEN7009/SICOM3009A/SICOM3306 have the same dimensions with SICOM3009A
-3S/M-6T.
As part of the heat dissipation system, the switch housing becomes hot during operation.
Please use caution when coming in contact and avoid covering the switch housing when the
switch is running.
The figures in this manual are only for reference.

Mounting
9
3.2 Mounting Modes and Steps
The device supports both DIN-rail mounting and panel mounting. Before installation, make
sure that the following requirements are met.
1) Environment: ambient temperature (see 8 Basic Features and Specifications), ambient
relative humidity (5% to 95%, non-condensing)
2) Power requirement: The power input is within the voltage range of the switch.
3) Grounding resistance: <5
4) No direct sunlight, distant from heat source and areas with strong electromagnetic
interference.
3.2.1 DIN-Rail Mounting
Mounting
Step 1: Select the mounting position for the device and guarantee adequate space and heat
dissipation for it (dimensions: 53.6mm×135mm×106.5mm).
Step 2: Insert the connecting seat onto the top of the DIN rail, and push the bottom of the
device inward and upward to ensure the DIN rail fits in the connecting seat. Make
sure the device is firmly installed on the DIN rail, as shown in the following figure.
Figure 6 DIN-Rail Mounting
Dismounting
Step 1: Insert the head of a screwdriver into the opening of the spring locking piece at the
bottom from the left. Lift the handle of the screwdriver to open the spring locking
piece of the connecting seat, as shown on the left of the following figure.
Step 2: Move the device in direction 2 until the bottom of the device is detached from the DIN
rail. Then move the device in direction 3 and uplift the device until the top of the

Mounting
10
connecting seat is detached from the DIN rail. In this way, the device is removed
from the DIN rail completely.
Figure 7 DIN-Rail Dismounting
3.2.2 Panel Mounting
Caution:
To adopt panel mounting, you need to purchase the plate for panel mounting (optional).
Mounting
Step 1: Use screws to fix the plate for panel mounting to the rear panel of the device.
Step 2: Select the mounting position (on a wall or inner wall of a cabinet) for the device and
guarantee adequate space and heat dissipation for it (dimensions:
53.6mm×135mm×106.5mm).
Step 3: Punch four holes in the selected position according to the dimensions for panel
mounting. Insert four screws into the four holes respectively, and turn the screws
with a screwdriver until about a 5mm distance is left between each screw head and
the wall.
Step 4: Align the four mounting holes on the plate for panel mounting with the four screws.
Make the screws pass through the Ф6.5 positions in the following figure. Move the
device in direction 1 until the four screws are in the Ф4 positions. Then tighten the
screws to complete mounting.

Mounting
11
Figure 8 Panel Mounting
Dismounting
Step 1: Loosen the four screws with a screwdriver. Move the device upward until the four
screws are in the Ф6.5 positions in the following figure. Then remove the plate for
panel mounting from the four screws to detach the device from the wall or inner wall
of the cabinet.
Step 2: Loosen the screws completely with a screwdriver. Remove them from the wall or
inner wall of the cabinet. Then remove the plate for panel mounting from the rear
panel to complete dismounting the device.
Figure 9 Panel Dismounting

Cable Connection
12
4 Cable Connection
4.1 10/100Base-T(X) Ethernet Port
10/100Base-T(X) Ethernet port is equipped with RJ45 connector. The port is self-adaptive. It
can automatically configure itself to work in 10M or 100M state, full or half duplex mode. The
port can also adapt to MDI or MDI-X connection automatically. You can connect the port to a
terminal or network device with a straight-through or cross-over cable.
Pin Definition
The following figure shows the pin numbers of the RJ45 port.
8 7 6 5 4 3 2 1
Figure 10 RJ45 Port
The following table lists the pin definitions of the 10/100Base-T(X) RJ45 port.
Table 7 Pin Definitions of 10/100Base-T(X) RJ45 Port
Pin
MDI-X Signal
MDI Signal
1
Receive Data+ (RD+)
Transmit Data+ (TD+)
2
Receive Data- (RD-)
Transmit Data- (TD-)
3
Transmit Data+ (TD+)
Receive Data+ (RD+)
6
Transmit Data- (TD-)
Receive Data- (RD-)
4, 5, 7, 8
Unused
Unused
Note:
"+" and "-" indicate level polarities.

Cable Connection
13
Wiring Sequence
Figure 11 Connection Using Straight-through/Cross-over Cable
Note:
The color of the cable for RJ45 connector meets the 568B standard: 1-orange and white,
2-orange, 3-green and white, 4-blue, 5-blue and white, 6-green, 7-brown and white, and 8-brown.
4.2 100Base-FX Ethernet Port
100Base-FX port is equipped with FC/ST/SC connector, and each port consists of TX
(transmit) port and RX (receive) port. To enable communication between Device A and
Device B, connect the TX (transmit) port of Device A to the RX (receive) port of Device B,
and the RX (receive) port of Device A to the TX (transmit) port of Device B. The following
figure shows the cable connection of the 100Base-FX Ethernet port. (The SC port is used as
an example. ST/FC cable connection is the same with SC.)
Figure 12 Cable Connection of 100Base-FX Ethernet Port

Cable Connection
14
Caution:
A laser is used to transmit signals in fiber cables. The laser meets the requirements of level 1
laser products. Routine operation is not harmful to your eyes, but do not look directly at the
100Base-FX Ethernet port when the switch is powered on.
4.3 1000Base-X, 10/100/1000Base-T(X) SFP Slot
1000Base-X, 10/100/1000Base-T(X) SFP slot (Gigabit SFP slot): You can enable data
transmission only after inserting an SFP optical/electrical module into the slot and
connecting cable properly. The following table lists the Gigabit SFP optical/electrical
modules (optional) supported by the series switches.
Table 8 Gigabit SFP Optical/Electrical Modules for SICOM3306
Model
Interface
MM/
SM
Connector
Center Wavelength
(CWL)
Transmission
Distance
IGSFP-M-SX-LC-850-0.55
1000Base-X port
MM
LC
850nm
0.55km
IGSFP-S-LX-LC-1310-10
1000Base-X port
SM
LC
1310nm
10km
IGSFP-S-LH-LC-1310-40
1000Base-X port
SM
LC
1310nm
40km
IGSFP-S-ZX-LC-1550-80
1000Base-X port
SM
LC
1550nm
80km
IG-FSFP-M-LX-LC-1310-2
100Base-FX port
MM
LC
1310nm
2km
IG-FSFP-S-LX-LC-1310-10
100Base-FX port
SM
LC
1310nm
10km
IGSFP-10/100/1000BASE-
T-RJ45
10/100/1000Base-T(
X) port (self-adaptive)
--
RJ45
connector
--
--
4.3.1 Gigabit SFP Optical Module
Figure 13 Gigabit SFP Optical Module
Gigabit SFP optical module is equipped with LC connector, and each port consists of a TX