KYLAND Technology SICOM3000A Series Assembly instructions

SICOM3000A Industrial Ethernet Switch
Hardware Installation Manual
Publication Data: Sep. 2017
Version: V1.0
No.: 112020149

SICOM3000A Industrial Ethernet Switch
Hardware Installation Manual
Disclaimer: Kyland Technology Co., Ltd. tries to keep the content of this manual as
accurate and as updated as possible. This document is not guaranteed to be error-free, and
we reserve the right to amend it without notice to users.
All rights reserved.
No part of this documentation may be excerpted, reproduced, translated, annotated or
duplicated, in any form or by any means without the prior written permission of KYLAND
Corporation.
Copyright © 2017 Kyland Technology Co., Ltd.

Notice for Safety Operation
The product performs reliably as long as it is used according to the guidance. Artificial
damage or destruction of the device should be avoided. Before using the device, read this
manual carefully for personal and equipment safety. Please keep the manual for further
reference. Kyland is not liable to any personal or equipment damage caused by violation of
this notice.
 Do not place the device near water sources or damp areas. Keep the ambient relative
humidity within the range from 5% to 95% (non-condensing).
 Do not place the device in an environment with high magnetic field, strong shock, or high
temperature. Keep the working and storage temperatures within the allowed range.
 Install and place the device securely and firmly.
 Please keep the device clean; if necessary, wipe it with a soft cotton cloth.
 Do not place any irrelevant materials on the device or cables. Ensure adequate heat
dissipation and tidy cable layout without knots.
 Wear antistatic gloves or take other protective measures when operating the device.
 Avoid any exposed metal wires because they may be oxidized or electrified.
 Install the device in accordance with related national and local regulations.
 Before power-on, make sure the power supply is within the allowed range of the device.
High voltage may damage the device.
 Power connectors and other connectors should be firmly interconnected.
 Do not plug in or out the power supply with wet hands. When the device is powered on,
do not touch the device or any parts with wet hands.
 Before operating a device connected to a power cable, remove all jewelry (such as rings,
bracelets, watches, and necklaces) or any other metal objects, because they may cause
electric shock or burns.
 Do not operate the device or connect or disconnect cables during an electrical storm.
 Use compatible connectors and cables. If you are not sure, contact our sales or
technical support personnel for confirmation.

 Do not disassemble the device by yourself. When an anomaly occurs, contact our sales
or technical support personnel.
 If any part is lost, contact our sales or technical support personnel to purchase the
substitute. Do not purchase parts from other channels.
 Dispose of the device in accordance with relevant national provisions, preventing
environmental pollution.
In the following cases, please immediately shut down your power supply and contact your
Kyland representative:
 Water gets into the equipment.
 Equipment damage or shell damage.
 Equipment operation or performance has abnormally changed.
 The equipment emits odor, smoke or abnormal noise.
The following information applies when operating this device in hazardous locations:
Suitable for use in Class I, Division 2, Groups A, B, C and D Hazardous Locations, or
nonhazardous locations only.
Cet appareillage est utilisable dans les emplacements de Classe I, Division 2, Groupes A, B,
C et D, ou dans les emplacements non dangereux seulement.
WARNING: EXPLOSION HAZARD
 Do not disconnect equipment while the circuit is live or unless the area is known to be
free of ignitable concentrations.
 Substitution of any component may impair suitability for Class I, Division 2.
AVERTISSEMENT: RISQUE D'EXPLOSION
 Avant de deconnecter l'equipement, couper le courant ou s'assurer que l'emplacement
est designe non dangereux.
 La substitution de composants peut rendre ce materiel inacceptable pour les
emplacements de Classe I, Division 2.

I
Contents
1 Product Overview ...............................................................................................................1
2 Structure and Interface .......................................................................................................3
2.1 Front Panel ..................................................................................................................3
2.2 Top Panel .....................................................................................................................4
3 Mounting .............................................................................................................................5
Dimension Drawing ..........................................................................................................5
3.1 ......................................................................................................................................5
3.2 Mounting Modes and Steps .........................................................................................6
3.2.1 DIN-Rail Mounting .................................................................................................6
3.2.2 Panel Mounting ......................................................................................................8
4 Connection ....................................................................................................................... 11
4.1 10/100Base-T(X) Ethernet Port .................................................................................. 11
4.2 100Base-FX Ethernet Port ......................................................................................... 12
4.3 100/1000Base-X, 10/100/1000Base-T(X) SFP slot .................................................... 13
4.3.1 SFP Optical Module ............................................................................................. 14
4.3.2 SFP Electrical Module ......................................................................................... 15
4.4 Console Port .............................................................................................................. 15
4.5 Grounding .................................................................................................................. 16
4.6 Power Terminal Block ................................................................................................ 17
4.7 Alarm Terminal Block ................................................................................................. 19
5 Reset ................................................................................................................................ 21
6 LEDs ................................................................................................................................. 22
7 Switch Access .................................................................................................................. 23
7.1 Access through Console Port ..................................................................................... 23
7.2 Access through Telnet ............................................................................................... 25
7.3 Access through Web .................................................................................................. 26
8 Basic Features and Specifications .................................................................................... 27

Product Overview
1
1 Product Overview
SICOM3000A includes a series of green low-consumption industrial Ethernet switches
applicable to subway PIS, petroleum and petrochemical, factory automation, intelligent
transportation, rail transit, and many other industries. The switch complies with the Railway
Signal Data Security Network Specifications V3.0 oriented towards the railway system.
The series switches provide Mini USB Console port, and supports one-touch recovery, and
network management through Web, Telnet, and console port.
SICOM3000A supports DIN rail mounting and panel mounting. It provides two
100/1000Base-X, 10/100/1000Base-T(X) SFP slots (Gigabit SFP Slot), and eight
10/100Base-T(X) Ethernet ports, The SPF slots support the optical power detection function.
For details, see the following table.
Table 1 Models
Models SICOM3000A-Ports-Connector-PS1-PS2
Code definition Code option
Ports: GX, S/M, T
2GX8T, 1S4T, 1M4T, 6T, 8T, 2S4T,2M4T,2S6T,2M6T
Note:
2GX8T: two 100/1000Base-X, 10/100/1000Base-T(X) SFP slots; eight
10/100Base-T(X) ports
1S4T: one 100Base-FX ports, single mode; four 10/100Base-T(X) ports.
1M4T: one 100Base-FX ports, multiple mode; four 10/100Base-T(X) ports
2S4T: two 100Base-FX ports, single mode; four 10/100Base-T(X) ports
2M4T: two 100Base-FX ports, multiple mode; four 10/100Base-T(X) ports
2S6T: two 100Base-FX ports, single mode; six 10/100Base-T(X) ports
2M6T: two 100Base-FX ports, multiple mode; six 10/100Base-T(X) ports
Connector: parameters for
S/M
Ports with M:
SC05=SC connector, 1310nm, 5km
ST05=ST connector, 1310nm, 5km

Product Overview
2
FC05=FC connector, 1310nm, 5km
Ports with S:
SC40=SC connector, 1310nm, 40km
ST40=ST connector, 1310nm, 40km
FC40=FC connector, 1310nm, 40km
SC60=SC connector, 1310nm, 60km
SC80=SC connector, 1550nm, 80km
Ports without S or M:
N/A
PS1-PS2: power input L3-L3 (24VDC, redundant power input)
Note：
For the product information listed in these tables, we reserve the right to amend it without notice.
To obtain the latest information, you can contact our sales or technical support personnel.

Structure and Interface
3
2 Structure and Interface
Caution:
It is recommended to purchase the port dustproof shield (optional) to keep ports clean and
ensure device performance.
2.1 Front Panel
Figure 1 Front Panel
(1) Power 1 LED (2) Power 2 LED (3) Running LED
(4) Ring LED (5) Alarm LED (6) 100Base-FX Ethernet port connection status LED
(7) Gigabit SFP Slot connection status LED (8) Reset button
(9) Console port (10) 10/100Base-T(X) Ethernet Port
(11) 10/100Base-T(X) Ethernet Port connection status LED (green)
(12) 10/100Base-T(X) Ethernet port speed LED (yellow)
(13) 100Base-FX Ethernet port (14) Gigabit SFP Slot

Structure and Interface
4
2.2 Top Panel
Figure 2 Top Panel

Mounting
5
3 Mounting
3.1 Dimension Drawing
Figure 3 Dimensions for DIN-Rail Mounting (unit: mm)
Figure 4 Dimensions for DIN-Rail Mounting (unit: mm)
Caution:
 As part of the heat dissipation system, the switch housing becomes hot during operation.

Mounting
6
Please use caution when coming in contact and avoid covering the switch housing when the
switch is running.
 The figures in this manual are only for reference.
3.2 Mounting Modes and Steps
The device supports both DIN-rail mounting and panel mounting. Before installation, make
sure that the following requirements are met.
1) Environment: temperature (-40 to ℃75 ), ambient relative humidity (5% to 95%, ℃
non-condensing)
2) Power requirement: The power input is within the voltage range of the switch.
3) Grounding resistance: <5
4) No direct sunlight, distant from heat source and areas with strong electromagnetic
interference.
5) Devices are to be installed in an authority certified enclosure and accessible only by the
use of a tool.
6) Devices should be installed and accessed by service personnel or users who have been
instructed about the reasons for the restrictions applied to the location and about any
precautions that shall be taken.
3.2.1 DIN-Rail Mounting
 DIN-Rail 1 Mounting
Step 1: Select the mounting position for the device and guarantee adequate space and heat
dissipation.
Step 2: Insert the connecting seat onto the top of the DIN rail, and push the bottom of the
device inward and upward to ensure the DIN rail fits in the connecting seat. Make sure the
device is firmly installed on the DIN rail, as shown in the following figure.

Mounting
7
Figure 5 DIN-Rail 1 Mounting
 DIN-Rail 1 Dismounting
Step 1: As shown in the following figure, press the device downward and move the device in
direction 1 until the bottom of the device is detached from the DIN rail.
Step 2: Pull the device upward and move the device in direction 2 until the device is removed
from the DIN rail completely.
Figure 6 DIN-Rail 1 Dismounting
 DIN-Rail 2 Mounting
Step 1: Select the mounting position for the device and guarantee adequate space and heat
dissipation.
Step 2: Insert the connecting seat onto the top of the DIN rail, and push the bottom of the
device inward and upward to ensure the DIN rail fits in the connecting seat. Make sure the
device is firmly installed on the DIN rail, as shown in the following figure.

Mounting
8
Figure 7 DIN-Rail 2 Mounting
 DIN-Rail 2 Dismounting
Step 1: Insert the head of a screwdriver into the opening of the spring locking piece at the
bottom from the left. Lift the handle of the screwdriver to open the spring locking piece of the
connecting seat, as shown on the left of the following figure.
Step 2: Move the device in direction 2 until the bottom of the device is detached from the DIN
rail. Then move the device in direction 3 and uplift the device until the top of the connecting
seat is detached from the DIN rail. In this way, the device is removed from the DIN rail
completely.
Figure 8 DIN-Rail 2 Dismounting
3.2.2 Panel Mounting
Note:
To adopt panel mounting, you need to purchase the plate for panel mounting (optional).

Mounting
9
 Mounting
Step 1: Use screws to fix the plate for panel mounting to the rear panel of the device.
Step 2: Select the mounting position (on a wall or inner wall of a cabinet) for the device and
guarantee adequate space and heat dissipation for it.
Step 3: Punch four holes in the selected position according to the dimensions for panel
mounting. Insert four screws into the four holes respectively, and turn the screws with a
screwdriver until about a 5mm distance is left between each screw head and the wall.
Step 4: Align the four mounting holes on the plate for panel mounting with the four screws.
Make the screws pass through the Ф6.5 positions in the following figure. Move the device in
direction 1 until the four screws are in the Ф4 positions. Then tighten the screws to complete
mounting.
Figure 9 Panel Mounting
 Dismounting
Step 1: Loosen the four screws with a screwdriver. Move the device upward until the four
screws are in the Ф6.5 positions in the following figure. Then remove the plate for panel
mounting from the four screws to detach the device from the wall or inner wall of the cabinet.
Step 2: Loosen the screws completely with a screwdriver. Remove them from the wall or
inner wall of the cabinet. Then remove the plate for panel mounting from the rear panel to
complete dismounting the device.

Mounting
10
Figure 10 Panel Dismounting
Caution:
Cut off the power and disconnect all cables before mounting, dismounting or moving the
equipment.

Connection
11
4 Connection
4.1 10/100Base-T(X) Ethernet Port
10/100Base-T(X) Ethernet port is equipped with RJ45 connector. The port is self-adaptive. It
can automatically configure itself to work in 10M or 100M state, full or half duplex mode. The
port can also adapt to MDI or MDI-X connection automatically. You can connect the port to a
terminal or network device with a straight-through or cross-over cable.
 Pin Definition
Figure 11 RJ45 Port
Table 2 Pin Definitions of 10/100Base-T(X) Ethernet Port
Pin MDI-X Signal MDI Signal
1 Receive Data+ (RD+) Transmit Data+ (TD+)
2 Receive Data- (RD-) Transmit Data- (TD-)
3 Transmit Data+ (TD+) Receive Data+ (RD+)
6 Transmit Data- (TD-) Receive Data- (RD-)
4, 5, 7, 8 Unused Unused
Note:
"+" and "-" indicate level polarities.
 Wiring Sequence

Connection
12
Figure 12 Connection Using Straight-through/Cross-over Cable
Note：
The color of the cable for RJ45 connector meets the 568B standard: 1-orange and white,
2-orange, 3-green and white, 4-blue, 5-blue and white, 6-green, 7-brown and white, and
8-brown.
4.2 100Base-FX Ethernet Port
100Base-FX Ethernet port is equipped with FC/ST/SC connector, and each port consists of
TX (transmit) port and RX (receive) port. To enable data transmission between Device A and
Device B, connect the TX port of Device A to the RX port of Device B, and the RX port of
Device A to the TX port of Device B. The following uses an SC port as an example. The
wiring sequence of an ST/FC port is the same with that of the SC port.
Figure 13 Connection of 100Base-FX Ethernet Port
Caution:
The device uses laser to transmit signals in fibers. The laser meets the requirements of level 1

Connection
13
laser products. Routine operation is not harmful to your eyes, but do not look directly at the fiber
port when the device is powered on.
4.3 100/1000Base-X, 10/100/1000Base-T(X) SFP slot
100/1000Base-X, 10/100/1000Base-T(X) SFP slot (gigabit SFP slot) requires an SFP
optical/electrical module to enable data transmission. The following table lists the SFP
optical/electrical modules (optional) supported by the series switches.
Table 3 SFP Optical/Electrical Modules
Model Port MM/SM Connector
Central
Wavelength
Transmission
Distance
IGSFP-M-SX-LC-850-0.55 1000Base-X port MM LC 850nm 0.55km
IGSFP-S-LX-LC-1310-10 1000Base-X port SM LC 1310nm 10km
IGSFP-S-LH-LC-1310-40 1000Base-X port SM LC 1310nm 40km
IGSFP-S-ZX-LC-1550-80 1000Base-X port SM LC 1550nm 80km
IFSFP-M-LX-LC-1310-2 100Base-X port MM LC 1310nm 2km
IFSFP-S-LH-LC-1310-40 100Base-X port SM LC 1310nm 40km
IGSFP-10/100/1000BASE-
T-RJ45
10/100/1000Base-
T(X) port
-- RJ45 -- --
Note:
The device uses the SFP module that supports digital diagnosis to support the optical power
detection function of the SFP slot. For details about the SFP module, consult our sales or
technical support personnel.

Connection
14
4.3.1 SFP Optical Module
Figure 14 SFP Optical Module
An SFP optical module is equipped with LC connector, and each port consists of a TX
(transmit) port and an RX (receive) port. To enable communication between Device A and
Device B, connect the TX port of Device A to the RX port of Device B, and the RX port of
Device A to the TX port of Device B, as shown in the following figure.
Figure 15 Fiber Connection of an SFP Optical Module
 How to Connect the SFP Optical Module
Insert the SFP optical module into the SFP slot in the switch, and then insert the fibers into
the TX port and RX port of the SFP module.
Figure 16 Connecting the SFP Optical Module
Identify the RX port and TX port of an SFP optical module:
1. Insert the two connectors in one end of two fibers into the SFP module, and those in the
other end into the peer module.
2. View the corresponding connection status LED:

Connection
15
If the LED is on, the connection is correct. If the LED is off, the link is not connected. This
may be caused by incorrect connection of the TX and RX ports. In this case, swop the two
connectors at one end of the fibers.
Caution:
 The device uses laser to transmit signals in fibers. The laser meets the requirements of level 1
laser products. Routine operation is not harmful to your eyes, but do not look directly at the
fiber port when the device is powered on.
 If the defined transmission distance of an SFP module is longer than 60km, do not use a short
fiber (<20km) for connection. If such a short fiber is used, the module will be burned.
4.3.2 SFP Electrical Module
Figure 17 SFP Electrical Module
 How to Connect the SFP Electrical Module
Insert the SFP electrical module into the SFP slot in the switch, and then insert the RJ45
connector of the twisted pair into the SFP module.
Figure 18 Connecting the SFP Electrical Module
4.4 Console Port
Caution:
To use the console port with a Mini USB connector, you need to purchase a USB console cable