KYLAND Technology KIEN3016A Assembly instructions


1
KIEN3016A
Industrial Ethernet Switch
Hardware Installation Manual
Kyland Technology Co., LTD.
Publication Date: Oct. 2011
Version: V1.0
Customer Service Hotline: [phone]
FAX: [phone]
Website: http://www.kyland.cn
E-mail: [email protected]
No.: 1.12.02.1030-0


2
KIEN3016AIndustrial Ethernet Switch
Hardware Installation Manual
Disclaimer: Kyland Technology Co., Ltd. tries to keep the content in this manual as accurate and
as up-to-date as possible.This document is not guaranteed to be error-free, and we reserve the
right to amend it without notice to users.
All rights reserved.
No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated,
in any form or by any means without the prior written permission of KYLAND Corporation.
Copyright ©2011 KYLAND Technology CO., LTD.


3
Notice for Safety Operation
This product performs reliably as long as it is used according to guidelines. Artificial damage or
destruction of the equipment should be avoided.
zRead this manual carefully and keep it for future reference;
zDo not place the equipment near water sources or damp areas;
zDo not place anything on power cable and put the cable in unreachable places;
zDo not tie or wrap the cable to prevent fire.
zPower connectors and other equipment connectors should be firmly interconnected
and checked frequently.
zDo not repair the equipment by yourself, unless it is clearly specified in the manual.
zPlease keep the equipment clean; if necessary, wipe the equipment with soft cotton cloth.
In the following cases, please immediately cut off the power supply and contact our company:
zWater gets into the equipment;
zEquipment damage or shell breakage;
zEquipment operation or performance has abnormally changed;
zThe equipment emits odor, smoke or abnormal noise.


4

Contents
1.PackingList...................................................................................................................................................5
2.ProductOverview......................................................................................................................................5
3.  StructureandInterface...........................................................................................................................5
3.1Front Panel......................................................................................................................5
3.2Top Panel........................................................................................................................7
4.  Mounting........................................................................................................................................................7
4.1 Mounting .......................................................................................................................7
4.2 Mounting Steps..............................................................................................................8
5.  CableConnection.....................................................................................................................................11
5.1 10/100Base-T(X).........................................................................................................11
5.2 100Base-FX.................................................................................................................12
5.3 Power...........................................................................................................................13
5.4 Grounding....................................................................................................................14
6.  LEDIndicators...........................................................................................................................................16
7.  ProductModelsandAccessories.......................................................................................................17
8.  BasicFeaturesandSpecifications.....................................................................................................18


5
1. Packing List
KIEN3016A Industrial Ethernet Switch 1
Hardware Installation Manual 1
CertificateofQuality(includingWarrantyCard) 1
Note: After unpacking, please check the accessories and the appearance of the equipment. If
anything is missing or damaged, please contact us.
2. Product Overview
KIEN3016A is a series of green, low power consumption and compact DIN-Rail
industrial Ethernet switch that can be applied extensively in wind power,
distribution network automation,subway PIS, power SCADA, wastewater
treatment, metallurgy, intelligent transportation, rail transit and many other
industries.
KIEN3016A industrial Ethernet switch supports DIN-Rail and panel mounting.It
supports IP40 protection class.
3. Structure and Interface
3.1Front Panel
KIEN3016A supports two kinds of product models.The interface is different for
each product model.
zKIEN3016A-2S/M-14T front panel is shown in Figure 1 below


6
1：PWR1-Power 1 LED
2：PWR2- Power 2 LED
3：(15、16)-two 100Base-FX port LEDs
4：(15、16)-two 100Base-FX ports
5：(1-14)-fourteen 10/100Base-T(X)
RJ45 ports
6：RJ45 port Speed LED
7：RJ45 port Link/ACT LED
Figure 1 Front Panel 1
zKIEN3016A-16T front panel is shown in
zFigure 2below
1: PWR1-Power 1 LED
2: PWR2-Power 2 LED
3:(1-16)-sixteen10/100/1000Base-T(X)
RJ45 ports
4:RJ45port Speed LED
5:RJ45portLink/ACT LED


7
Figure 2 Front Panel 2
3.2Top Panel
1: Terminal block for power input
2: Screw hole for grounding
Figure 3 Top Panel
4. Mounting
4.1 Mounting
zDimension Drawing for DIN-Rail Mounting (Unit: mm)


8
Figure 4 DIN-Rail Mounting
zDimension Drawing for Panel Mounting (Unit: mm)
Figure 5 Panel Mounting
4.2 Mounting Steps
zKIEN3016A DIN-Rail Mounting
The specific steps are as follows:
Step 1: Select the mounting position for KIEN3016A and ensure that there is
adequate space.
Step 2: Insert the top of the DIN-Rail into the spring-supported slot of the


9
DIN-Rail connecting seat in the rear panel of KIEN3016A as seen below;
move the device in the direction of arrow 2 to put the whole Din-Rail into place;
verify the KIEN3016A is firmly mounted on the DIN-Rail, as shown below.
Figure 6 DIN-Rail Mounting
zRemove KIEN3016A from DIN-Rail
The specific steps are as follows:
Step 1: Place the screwdriver into the hole at the bottom of spring locking
plate; press the plate down to loosen the connection of DIN-Rail and switch,
as shown in arrow 1.
Step 2:Pull the KIEN3016A up in the direction of arrow 2; meanwhile remove
the device from the DIN-Rail along the direction of arrow 3.
Figure 7 DIN-Rail Dismounting


10
zKIEN3016APanel Mounting
The specific steps are as follows:
Step 1: Select the mounting position for KIEN3016A on the wall or in cabinet;
ensure that there is adequate space for the switch.
Step 2: Drill 4 holes on the selected position according to the panel mounting
dimension drawings; use a cross-screwdriver to screw 4 cross-slot screws
(M3×10) into holes. Don’t tighten the screws completely; leave about 5mm of
space between.
Step 3: Aim 4 mounting holes on KIEN3016A mounting plate at 4 fixed screws;
pass the screws through 4 holes with the diameter of 6.5mm (Ф6.5); then slide
down KIEN3016A as seen below; finally screw 4 screws tightly. Now the
KIEN3016A should be firmly fixed to the wall or cabinet.
Figure 8 Panel Mounting
zRemove KIEN3016A from wall or cabinet
The specific steps are as follows:
Step 1: Use a screwdriver to loosen 4 screws; move the device up to let
screws into 4 holes with the diameter of 6.5mm (Ф6.5).
Step 2: Unscrew the screws from wall or cabinet; remove the device from wall


11
or cabinet.
Figure 9 Panel Dismounting
5. Cable Connection
5.1 10/100Base-T(X)
10/100Base-T(X) Ethernet RJ45 port can be connected to terminal equipment and
network devices with straight-through cables or crossover cables. RJ45
connectors must be attached at both ends of the cable.
zRJ45 port and pin number
Figure 10 RJ45 Port
zPin distribution of 10/100Base-T(X)
Table 1 Pin Distribution of 10/100Base-T(X)
Pin MDI-X signal name MDI signal name
1 Receiving data+(RD+) Output data+(TD+)
2 Receiving data-(RD-) Output data-(TD-)
3 Output data+(TD+) Receiving data+(RD+)
6 Output data-(TD-) Receiving data-(RD-)
8 7 6 5 4 3 2 1


12
4,5,7,8 Unused Unused
Note: “+”“-”mean level polarity.
z100M straight-through cable wiring
Figure 11 100M Straight-through Cable Wiring
z100M crossover cable wiring
Figure 12 100M Crossover Cable Wiring
5.2 100Base-FX
z100Base-FX Parameter Table
Table 2 100Base-FX Parameter Table
Property FX(FC/SC/ST)
Type Multimode Single mode Single mode Single mode Single mode
Central Wavelength (nm) 1310 1310 1310 1550 1550


13
Property FX(FC/SC/ST)
Transmission Distance (Km) 2 5 40 60 60 80
Applicable Distance (Km) 0~2 0~5 0~40 6~60 4~60 10~80
Luminous
power Min. (dBm) -19 -12 -8 -8 -8
Max. (dBm) -11 -4 0 -2 0
Receiving Sensitivity (dBm) -31 -34 -34 -34 -34
Overload Luminous Power
(dBm) -3 -3 -3 -3
-3
z100M fiber port wiring (Take SC port as example; ST/FC wiring method is the
same with SC)
Figure 13 100M Fiber Port Wiring
Note: A laser is used to transmit signals in fiber cables. The laser meets the requirements of level
1 laser products. Routine operation is not harmful to your eyes, but do not look directly at the fiber
port and fiber connector when the switch is powered on.
5.3 Power
According to the power input requirements, use a 5.08mm-spacing terminal block
to connect the power cable.
Note: The cross section area of the power cable is required to be greater than 0.75mm2and less
than 2.5mm2. The grounding resistance requirement: <5Ω.


14
z5.08mm power terminal block pin number is shown in Figure 14
Figure 14 Pin 5.08mm Power Terminal Block
z5.08mm power terminal block contact definition
Table 3 Contact Definition
Contact number DC wiring definition AC wiring definition
1 PWR1: + PWR1: L
2 PWR1: - PWR1: N
3 Protection Ground Protection Ground
4 PWR2: - PWR2: N
5 PWR2: + PWR2: L
zWiring and mounting
Step 1: Take the power terminal block off KIEN3016A
Step 2: Insert the power cable into the terminal block and fix the power cable
Step 3: Put the terminal block back to KIEN3016A with the connected cable
5.4 Grounding
zChassis grounding and power terminal grounding


15
Figure 15 Chassis Grounding and Power Terminal Grounding
There is a grounding screw on the top panel of the KIEN3016A, which is for
chassis grounding. One end of the chassis grounding cable is connected with
the grounding screw and the other end of the cable is reliably grounded. (The
cross section area of chassis grounding cable should be more than 2.5mm2.
The grounding resistance requirement: <5Ω)
The grounding part in the 5.08mm power terminal block is called surge
grounding.
It is required to connect the chassis grounding part with the surge grounding
part by an18#AWG yellow-green line as seen below
z18#AWG yellow-green line (Unit: mm)


16
Figure 16 18#AWG Yellow-green Line
Note: If KIEN3016A needs to do a dielectric voltage withstand test, in order to ensure proper
testing, please disconnect the 18#AWG yellow-green line to disable surge protection circuit that
connects to surge grounding
Figure 17 Disconnect 18#AWG Yellow-green Line
6. LED Indicators
Table 4 KIEN3016A LED Indicators


17
LED State Description
Power LEDs
PWR1 ON Power 1 connects and operates normally.
OFF Power 1 disconnects or operates abnormally.
PWR2 ON Power 2 connects and operates normally.
OFF Power2 disconnects or operates abnormally.
Ethernet RJ45 port LEDs
Each RJ45 Ethernet port has two indicators a yellow LED and a green LED. The yellow LED
indicates port rate, while the green LED indicates port connection state.
Speed
(Yellow)
ON 100M working state
OFF 10M working state or no connection
Link/Act
(Green)
ON Effective network connection in the port
Blinking Network activities in the port
OFF No effective network connection in the port
100Base-FX LEDs
Link/Act
ON Effective network connection in the port
Blinking Network activities in the port
OFF No effective network connection in the port
7. Product Models and Accessories
zThe specific configuration models of KIEN3016A are shown in Table 5
Table 5 KIEN3016A Configuration Table
Model Description Power
KIEN3016A-16T 16 10/100Base-T(X)RJ45
Ports
12VDC(9~36VDC),
24VAC/DC(18~50VAC/18-72VDC),
dual redundant power inputs
KIEN3016A-2S/M-14T
2 100Base-FX Fiber Ports,
1410/100Base-T(X) RJ45
Ports
zThe optional accessories of KIEN3016A are shown inTable 6
Table 6 KIEN3016A Optional Accessories


18
Model Description
DT-BGAZ-02 Panel mounting kit
DT-FCZ-RJ45-01 RJ45 dustproof shield
8. Basic Features and Specifications
zCable
Twisted Pair: 100m (Standard CAT5, CAT5e network cable)
Multi Mode Fiber: 1310nm, 5Km (100Mbps)
Single Mode Fiber:1310nm, 40Km/60Km(100Mbps);
1550nm, 60Km /80Km(100Mbps)
zPower Requirements
Power input: 12VDC (9~36VDC), 24VAC/DC (18~50VAC, 18~72VDC)
Power terminal: 5-pin 5.08mm-spacing plug-in terminal block
Power consumption:
KIEN3016A-16T:6.1W
KIEN3016A-2S/M-14T:6.6W
zPhysical Characteristics
Housing: Metal, fanless
Installation: DIN-Rail or Panel mounting
Dimensions (W×H×D): 88mm×135mm×137mm
Weight: 1.2Kg
zEnvironment Limits
Operating Temperature: -40℃to 85℃(-40 to 185℉)


19
Storage Temperature: -40℃to 85℃(-40 to 185℉)
Ambient Relative Humidity: 5% to 95% (non-condensing)
zMTBF: 361000h
zWarranty: 5 years