KYLAND Technology KIEN1009 Assembly instructions

KIEN1009 Industrial Ethernet Switch
Hardware Installation Manual
Kyland Technology Co., Ltd.
Publication Date: Mar. 2013
Version: V1.0󱾡󱾡󱾡󱾡󱾡
FAX: [phone]
Website: http://www.kyland.com
E-mail: [email protected]
No.: 1.12.02.1049-0

KIEN1009 Industrial Ethernet Switch
Hardware Installation Manual
Disclaimer: Kyland Technology Co., Ltd. tries to keep the content of this manual as accurate
and as updated as possible. This document is not guaranteed to be error-free, and we reserve
the right to amend it without notice to users.
All rights reserved.
No part of this documentation may be excerpted, reproduced, translated, annotated or
duplicated, in any form or by any means without the prior written permission of KYLAND
Corporation.
Copyright © 2013 Kyland Technology Co., Ltd.

Notice for Safety Operation
The product performs reliably as long as it is used according to the guidance. Artificial damage or
destruction of the device should be avoided. Before using the device, read this notice carefully
for personal and equipment safety. Please keep the manual for further reference. Kyland is not
liable to any personal or equipment damage caused by violation of this notice.
 Do not place the device near water sources or damp areas. Keep the ambient relative
humidity within the range from 5% to 95% (non-condensing).
 Do not place the device in an environment with high magnetic field, strong shock, or high
temperature. Keep the working and storage temperatures within the allowed range.
 Install and place the device securely and firmly.
 Please keep the device clean; if necessary, wipe it with a soft cotton cloth.
 Do not place any irrelevant materials on the device or cables. Ensure adequate heat
dissipation and tidy cable layout without knots.
 Wear antistatic gloves or take other protective measures when operating the device.
 Avoid any exposed metal wires because they may be oxidized or electrified.
 Install the device in accordance with related national and local regulations.
 Before power-on, make sure the power supply is within the allowed range of the device. High
voltage may damage the device.
 Power connectors and other connectors should be firmly interconnected.
 Do not plug in or out the power supply with wet hands. When the device is powered on, do
not touch the device or any parts with wet hands.
 Before operating a device connected to a power cable, remove all jewelry (such as rings,
bracelets, watches, and necklaces) or any other metal objects, because they may cause
electric shock or burns.
 Do not operate the device or connect or disconnect cables during an electrical storm.
 Use compatible connectors and cables. If you are not sure, contact our sales or technical
support personnel for confirmation.
 Do not disassemble the device by yourself. When an anomaly occurs, contact our sales or
technical support personnel.
 If any part is lost, contact our sales or technical support personnel to purchase the substitute.
Do not purchase parts from other channels.

 Dispose of the device in accordance with relevant national provisions, preventing
environmental pollution.
In the following cases, please immediately shut down your power supply and contact your
Kyland representative:
 Water gets into the equipment.
 Equipment damage or shell damage.
 Equipment operation or performance has abnormally changed.
 The equipment emits odor, smoke or abnormal noise.

I
Contents
1Product Overview .................................................................................................................... 1
2Structure and Interface ............................................................................................................ 2
2.1 Front Panel ......................................................................................................................... 2
2.2 Top Panel ........................................................................................................................... 5
3Mounting .................................................................................................................................. 6
3.1 Dimension Drawing ............................................................................................................. 6
3.2 Mounting Modes and Steps ................................................................................................ 7
3.2.1DIN-Rail Mounting ......................................................................................................... 7
3.2.2Panel Mounting ............................................................................................................. 8
4Connection ............................................................................................................................. 10
4.1 10/100Base-T(X) Ethernet Port ........................................................................................ 10
4.2 100Base-FX Ethernet Port ................................................................................................ 11
4.3 1000Base-X, 10/100/1000Base-T(X) SFP Slot ................................................................. 12
4.3.1Gigabit SFP Optical Module ........................................................................................ 12
4.3.2Gigabit SFP Electrical Module ..................................................................................... 13
4.4 Grounding ......................................................................................................................... 14
4.5 Power Terminal Block ....................................................................................................... 14
5LEDs ...................................................................................................................................... 18
6Basic Features and Specifications ......................................................................................... 19

Product Overview
1
1 Product Overview
KIEN1009 includes a series of green low-consumption industrial Ethernet switches applicable to
wind power, distribution network automation, subway PIS, power SCADA, sewage treatment,
metallurgy, intelligent transportation, rail transit, and many other industries. KIEN1009 supports
redundant DC and AC power input of wide voltage range and provides
normal-temperature-range and wide-temperature-range models.
The series switches support DIN-rail and panel mounting. KIEN1009 provides up to six
10/100Base-T(X) Ethernet ports, two 100Base-FX Ethernet ports, and one 1000Base-X,
10/100/1000Base-T(X) SFP slot (gigabit SFP slot).
Table 1 KIEN1009 Models
Model
Port
Power Supply
Remarks
Gigabit
SFP
slot
100Base-FX
Ethernet
port
10/100Base-
T(X) Ethernet
port
KIEN1009-E-8T
--
--
8
24DC (single
power supply)
Normal temperature
range (0℃~60℃)
KIEN1009-8T
--
--
8
12DCW,
24DCW,
(redundant
power supply)
Wide temperature
range (-40℃~85℃)
KIEN1009-1S/M-7T
--
1
7
KIEN1009-2S/M-6T
--
2
6
KIEN1009-3S/M-6T
--
3
6
KIEN1009-1GX-2S/M-6T
1
2
6
Note:
We reserve the right to amend the product information listed in this table without notice. To obtain the
latest information, contact our sales or technical support personnel.

Structure and Interface
2
2 Structure and Interface
Caution:
It is recommended to purchase the port dustproof shield (optional) to keep ports clean and ensure
switch performance.
2.1 Front Panel
 Front Panel of KIEN1009-E-8T
Figure 1 Front Panel of KIEN1009-E-8T
Table 2 Description of the Front Panel of KIEN1009-E-8T
No.
Identifier
Description
(1)
PWR
Power LED
(2)
1-8
Eight 10/100Base-T(X) Ethernet ports
(3)
--
10/100Base-T(X) Ethernet port speed LED (yellow)
(4)
--
10/100Base-T(X) Ethernet port connection status LED (green)

Structure and Interface
3
 Front Panel of KIEN1009-8T
Figure 2 Front Panel of KIEN1009-8T
Table 3 Description of the Front Panel of KIEN1009-8T
No.
Identifier
Description
(1)
PWR1
Power 1 LED
(2)
PWR2
Power 2 LED
(3)
1-8
Eight 10/100Base-T(X) Ethernet ports
(4)
--
10/100Base-T(X) Ethernet port speed LED (yellow)
(5)
--
10/100Base-T(X) Ethernet port connection status LED (green)

Structure and Interface
4
 Front Panel of KIEN1009-1GX-2S/M-6T
Figure 3 Front Panel of KIEN1009-1GX-2S/M-6T
Table 4 Description of the Front Panel of KIEN1009-1GX-2S/M-6T
No.
Identifier
Description
(1)
PWR1
Power 1 LED
(2)
PWR2
Power 2 LED
(3)
G1
Gigabit SFP slot connection status LED
(4)
G1
Gigabit SFP slot
(5)
7-8
100Base-FX Ethernet port connection status LEDs
(6)
7-8
Two 100Base-FX Ethernet ports
(7)
1-6
Six 10/100Base-T(X) Ethernet ports
(8)
--
10/100Base-T(X) Ethernet port speed LED (yellow)
(9)
--
10/100Base-T(X) Ethernet port connection status LED (green)

Structure and Interface
5
2.2 Top Panel
Figure 4 Top Panel 1
Figure 5 Top Panel 2
Table 5 Description of Top Panel
No.
Identifier
Description
(1)
Power terminal block
(2)
Power terminal block
(3)
--
Grounding screw
Note:
Top panel 1 is applicable to KIEN1009-E-8T.
Top panel 2 is applicable to KIEN1009-8T, KIEN1009-1S/M-7T, KIEN1009-2S/M-6T,
KIEN1009-3S/M-6T, and KIEN1009-1GX-2S/M-6T.

Mounting
6
3 Mounting
3.1 Dimension Drawing
Figure 6 Dimensions for DIN-Rail Mounting (unit: mm)
Figure 7 Dimensions for Panel Mounting (unit: mm)
Caution:
 As part of the heat dissipation system, the switch housing becomes hot during operation. Please
use caution when coming in contact and avoid covering the switch housing when the switch is
running.

Mounting
7
 KIEN1009-3S/M-6T is used as an example to show the dimensions and mounting modes. The
dimensions and mounting modes of other models are similar.
3.2 Mounting Modes and Steps
The series switches support DIN-rail and panel mounting. Before installation, make sure that the
following requirements are met.
1) Environment: temperature (see Table 1), ambient relative humidity (5% to 95%,
non-condensing)
2) Power requirement: The power input is within the voltage range of the switch.
3) Grounding resistance: <5
4) No direct sunlight, distant from heat source and areas with strong electromagnetic
interference.
3.2.1 DIN-Rail Mounting
 Mounting
Step 1: Select the mounting position for the device and guarantee adequate space and heat
dissipation (dimensions: 53.6mm×135mm×106.5mm).
Step 2: Insert the connecting seat onto the top of the DIN rail, and push the bottom of the device
inward and upward to ensure the DIN rail fits in the connecting seat. Make sure the
device is firmly installed on the DIN rail, as shown in the following figure.
Figure 8 DIN-Rail Mounting

Mounting
8
 Dismounting
Step 1: Insert the head of a screwdriver into the opening of the spring locking piece at the bottom
from the left. Lift the handle of the screwdriver to open the spring locking piece of the
connecting seat, as shown on the left of the following figure.
Step 2: Move the device in direction 2 until the bottom of the device is detached from the DIN rail.
Then move the device in direction 3 and uplift the device until the top of the connecting
seat is detached from the DIN rail.
Figure 9 DIN-Rail Dismounting
3.2.2 Panel Mounting
Caution:
Purchase the plate (optional) for panel mounting.
 Mounting
Step 1: Use screws to secure the plate for panel mounting to the rear panel of the device.
Step 2: Select the mounting position (on a wall or inner wall of a cabinet) for the device and
guarantee adequate space and heat dissipation (dimensions:
53.6mm×135mm×106.5mm).
Step 3: Punch four holes in the selected position according to the dimensions for panel mounting.
Insert four screws into the four holes respectively, and turn the screws with a screwdriver
until about a 5mm distance is left between each screw head and the wall.
Step 4: Align the four mounting holes on the plate for panel mounting with the four screws. Insert

Mounting
9
the screws through the Ф6.5 positions in the following figure. Move the device in
direction 1 until the screws are in the Ф4 positions. Then tighten the screws.
Figure 10 Panel Mounting
 Dismounting
Step 1: Loosen the four screws with a screwdriver. Pull the device upward until the four screws
are in the Ф6.5 positions in the following figure. Then remove the plate for panel
mounting from the four screws to detach the device from the wall or inner wall of the
cabinet.
Step 2: Loosen the screws completely with a screwdriver. Remove them from the wall or inner
wall of the cabinet. Then remove the plate for panel mounting from the rear panel to
complete dismounting the device.
Figure 11 Panel Dismounting

Connection
10
4 Connection
4.1 10/100Base-T(X) Ethernet Port
10/100Base-T(X) Ethernet port is equipped with RJ45 connector. The port is self-adaptive. It can
automatically configure itself to work in 10M or 100M state, full or half duplex mode. The port can
also adapt to MDI or MDI-X connection automatically. You can connect the port to a terminal or
network device with a straight-through or cross-over cable.
 Pin Definition
The following figure shows the pin numbers of the 10/100Base-T(X) RJ45 port.
8 7 6 5 4 3 2 1
Figure 12 RJ45 Port
The following table lists the pin definitions of the 10/100Base-T(X) RJ45 port.
Table 6 Pin Definitions of 10/100Base-T(X) RJ45 Port
Pin
MDI-X Signal
MDI Signal
1
Receive Data+ (RD+)
Transmit Data+ (TD+)
2
Receive Data- (RD-)
Transmit Data- (TD-)
3
Transmit Data+ (TD+)
Receive Data+ (RD+)
6
Transmit Data- (TD-)
Receive Data- (RD-)
4, 5, 7, 8
Unused
Unused
Note:
"+" and "-" indicate level polarities.

Connection
11
 Wiring Sequence
Figure 13 Connection Using Straight-through/Cross-over Cable
Note:
The color of the cable for RJ45 connector meets the 568B standard: 1-orange and white, 2-orange,
3-green and white, 4-blue, 5-blue and white, 6-green, 7-brown and white, and 8-brown.
4.2 100Base-FX Ethernet Port
100Base-FX Ethernet port is equipped with FC/ST/SC connector, and each port consists of TX
(transmit) port and RX (receive) port. To enable data transmission between Device A and Device
B, connect the TX port of Device A to the RX port of Device B, and the RX port of Device A to the
TX port of Device B. The following uses an SC port as an example. The wiring sequence of an
ST/FC port is the same with that of the SC port.
Figure 14 Connection of 100Base-FX Ethernet Port
Caution:
The device uses laser to transmit signals in fibers. The laser meets the requirements of level 1 laser
products. Routine operation is not harmful to your eyes, but do not look directly at the fiber port when
the device is powered on.

Connection
12
4.3 1000Base-X, 10/100/1000Base-T(X) SFP Slot
1000Base-X, 10/100/1000Base-T(X) SFP slot (gigabit SFP slot) requires an SFP
optical/electrical module to enable data transmission. The following table lists the gigabit SFP
optical/electrical modules (optional) supported by the series switches.
Table 7 Gigabit SFP Optical/Electrical Modules
Model
Port
MM/SM
Connector
Central
Wavelength
Transmission
Distance
IGSFP-M-SX-LC-850-0.55
1000Base-X port
MM
LC
850nm
0.55km
IGSFP-S-LX-LC-1310-10
1000Base-X port
SM
LC
1310nm
10km
IGSFP-S-LH-LC-1310-40
1000Base-X port
SM
LC
1310nm
40km
IGSFP-S-ZX-LC-1550-80
1000Base-X port
SM
LC
1550nm
80km
IGSFP-10/100/1000BASE-
T-RJ45
10/100/1000Base-T(X
) port
--
RJ45
--
--
4.3.1 Gigabit SFP Optical Module
Figure 15 Gigabit SFP Optical Module
An SFP optical module is equipped with LC connector, and each port consists of a TX (transmit)
port and an RX (receive) port. To enable communication between Device A and Device B,
connect the TX port of Device A to the RX port of Device B, and the RX port of Device A to the TX
port of Device B, as shown in the following figure.
Figure 16 Fiber Connection of the SFP Optical Module

Connection
13
 How to Connect the SFP Optical Module
Insert the SFP optical module into the SFP slot in the switch, and then insert the fibers into the
TX port and RX port of the SFP module.
Figure 17 Connecting the SFP Optical Module
Identify the RX port and TX port of an SFP optical module:
1. Insert the two connectors in one end of two fibers into the SFP module, and those in the other
end into the peer module.
2. View the corresponding connection status LED:
If the LED is on, the connection is correct. If the LED is off, the link is not connected. This may
be caused by incorrect connection of the TX and RX ports. In this case, swop the two
connectors at one end of the fibers.
Caution:
 The device uses laser to transmit signals in fibers. The laser meets the requirements of level 1 laser
products. Routine operation is not harmful to your eyes, but do not look directly at the fiber port when
the device is powered on.
 If the defined transmission distance of an SFP module is longer than 60km, do not use a short fiber
(<20km) for connection. If such a short fiber is used, the module will be burned.
4.3.2 Gigabit SFP Electrical Module
Figure 18 Gigabit SFP Electrical Module

Connection
14
 How to Connect the SFP Electrical Module
Insert the SFP electrical module into the SFP slot in the switch, and then insert the RJ45
connector of the twisted pair into the SFP module.
Figure 19 Connecting the SFP Electrical Module
4.4 Grounding
Grounding protects the switch from lightning and interference. Therefore, you must ground the
switch properly. You need to ground the switch before it is powered on and disconnect the
grounding cable after the switch is powered off.
The switch provides a grounding screw on the top panel for chassis grounding. After crimping
one end of the grounding cable to a cold pressed terminal, secure the end to the grounding
screw and connect the other end to the earth firmly.
Figure 20 Grounding
Note:
Cross-sectional area of the chassis grounding cable>2.5mm2; grounding resistance<5
4.5 Power Terminal Block
There is a power terminal block on the top panel of the device. You need to connect the power
wires to the terminal block to provide power for the device. The device supports single power
supply with 3-pin 5.08mm-spacing plug-in terminal block and redundant power supply with 5-pin
5.08mm-spacing plug-in terminal block. When the redundant power supply is used and one

Connection
15
power input is faulty, the device can continue operating properly, thereby improving network
reliability.
Note:
0.75mm2<Cross-sectional area of the power wire<2.5mm2; grounding resistance<5
 3-Pin 5.08mm-Spacing Plug-in Terminal Block (single power input)
The following figure shows the 3-pin 5.08mm-spacing plug-in terminal block.
Figure 21 3-Pin 5.08mm-Spacing Plug-in Terminal Block (socket)
The following table lists the pin definitions of the 3-pin 5.08mm-spacing plug-in terminal block.
Table 8 Pin Definitions of 3-Pin 5.08mm-Spacing Plug-in Terminal Block
No.
DC Definition
AC Definition
1
PWR: +
PWR: L
2
PWR: -
PWR: N
3
PGND
PGND
 5-Pin 5.08mm-Spacing Plug-in Terminal Block (redundant power input)
The following figure shows the 5-pin 5.08mm-spacing plug-in terminal block.
Figure 22 5-Pin 5.08mm-Spacing Plug-in Terminal Block (socket)