KYLAND Technology SICOM3024P User manual

SICOM3024P Industrial Ethernet Switch
Hardware Installation Manual
Kyland Technology Co., Ltd.
Publication Date: May. 2013
Version: V2.7
FAX: [phone]
Website: http://www.kyland.com
E-mail: [email protected]

SICOM3024P Industrial Ethernet Switch
Hardware Installation Manual
Disclaimer: Kyland Technology Co., Ltd. tries to keep the content of this manual as accurate and
as updated as possible. This document is not guaranteed to be error-free, and we reserve the right
to amend it without notice to users.
All rights reserved.
No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated,
in any form or by any means without the prior written permission of KYLAND Corporation.
Copyright © 2013 Kyland Technology Co., Ltd.

Notice for Safety Operation
The product performs reliably as long as it is used according to the guidance. Artificial damage or
destruction of the device should be avoided. Before using the device, read this notice carefully for
personal and equipment safety. Please keep the manual for further reference. Kyland is not liable to
any personal or equipment damage caused by violation of this notice.
Do not place the device near water sources or damp areas. Keep the ambient relative humidity
within the range from 5% to 95% (non-condensing).
Do not place the device in an environment with high magnetic field, strong or ongoing vibrations
or high temperature. Keep the working and storage temperatures within the allowed range.
Install and place the device securely and firmly.
Please keep the device clean; if necessary, wipe it with soft cotton cloth.
Do not place any irrelevant materials on the device or cables. Ensure adequate heat dissipation
and tidy cable layout without being entangled or knotted.
Wear antistatic gloves or take other protective measures when operating the device.
Avoid any exposed metal wires because they may be oxidized or electrified.
Install the device in accordance with related national and local regulations.
Before power-on, make sure the power supply is within the allowed range of the device. High
voltage may damage the device.
Power connectors and other connectors should be firmly interconnected.
Do not plug in or out the power supply with wet hands. When the device is powered on, do not
touch the device or any parts with wet hands.
Before operating a device connected to a power cable, remove all jewelries (such as rings,
bracelets, watches, and necklaces) or any other metal objects, because they may cause
electric shock or burns.
Do not operate the device or connect or disconnect cables during lightning.
Use compatible connectors and cables. If you are not sure, contact our sales or technical
support personnel for confirmation.
Do not disassemble the device by yourself. When an anomaly occurs, contact our sales or
technical support personnel.
If any part is lost, contact our sales or technical support personnel to purchase the substitute.
Do not purchase parts from other channels.

Dispose of the device in accordance with relevant national provisions, preventing
environmental pollution.
In the following cases, please immediately shut down your power supply and contact your Kyland
representative:
Water gets into the equipment.
Equipment damage or shell damage.
Equipment operation or performance has abnormally changed.
The equipment emits odor, smoke or abnormal noise.

I
Contents
1Product Overview ........................................................................................................................ 1
2Structure and Interface ................................................................................................................ 4
2.1 Front Panel............................................................................................................................. 4
2.2 Rear Panel.............................................................................................................................. 5
3Switch Installation........................................................................................................................ 7
3.1 Dimension Drawing................................................................................................................. 7
3.2 Mounting Modes and Steps.................................................................................................... 8
4Cable Connection...................................................................................................................... 10
4.1 10/100Base-T(X) Ethernet port............................................................................................. 10
4.2 100Base-FX Port.................................................................................................................. 11
4.3 10/100/1000Base-T(X) Ethernet Port ................................................................................... 11
4.4 1000Base-X, 10/100/1000Base-T(X) SFP Slot..................................................................... 13
4.4.1Gigabit SFP Optical Module............................................................................................ 13
4.4.2Gigabit SFP Electrical Module......................................................................................... 14
4.5 Console Port......................................................................................................................... 15
4.6 Grounding............................................................................................................................. 16
4.7 Power Terminal Block........................................................................................................... 16
4.8 Alarm Terminal Block............................................................................................................ 18
5LEDs.......................................................................................................................................... 20
6Switch Access............................................................................................................................ 22
6.1 Access through Console Port............................................................................................... 22
6.2 Access through Telnet.......................................................................................................... 24
6.3Access through Web............................................................................................................. 24
7Basic Features and Specifications............................................................................................. 25

Product Overview
1
1 Product Overview
SICOM3024P includes a series of managed industrial Ethernet switches tailored for power, rail
transit, and coal mining industries. Capable of working properly in rugged environment,
SICOM3024P conforms to IEC61850-3 and IEEE1613 standards and adopts internal modular
design for flexible expansion.
The series switches support 19 inch 1U rack mounting by front/rear panel. They provide up to four
slots for 1000Base-X, 10/100/1000Base-T(X) SFP modules (Gigabit SFP Slot) or four
10/100/1000Base-T(X) Ethernet ports, and twenty-four fast Ethernet fiber or RJ45 (optional) ports,
suitable for access layer networks.
Table 1 SICOM3024P Models
Model
Interface
Power
Gigabit SFP
Slot
10/100/1000
Base-T(X)
Ethernet
port
100Base-
FX Ethernet
port
10/100
Base-T(X)
Ethernet
port
SICOM3024P-4GX-24S/M
4
--
24
--
24DC,
48DC,
220AC/DCW
(single and
redundant
power
supply)
SICOM3024P-4GX-20S/M-4T
4
--
20
4
SICOM3024P-4GX-16S/M-8T
4
--
16
8
SICOM3024P-4GX-16S/M
4
--
16
--
SICOM3024P-4GX-12S/M-12T
4
--
12
12
SICOM3024P-4GX-8S/M-16T
4
--
8
16
SICOM3024P-4GX-8S/M
4
--
8
--
SICOM3024P-4GX-4S/M-20T
4
--
4
20
SICOM3024P-4GX-2S/M-22T
4
--
2
22
SICOM3024P-4GX-24T
4
--
--
24
SICOM3024P-2GX-24S/M
2
--
24
--
SICOM3024P-2GX-20S/M-4T
2
--
20
4
SICOM3024P-2GX-16S/M-8T
2
--
16
8

Product Overview
2
SICOM3024P-2GX-16S/M
2
--
16
--
SICOM3024P-2GX-12S/M-12T
2
--
12
12
SICOM3024P-2GX-8S/M-16T
2
--
8
16
SICOM3024P-2GX-8S/M
2
--
8
--
SICOM3024P-2GX-4S/M-20T
2
--
4
20
SICOM3024P-2GX-2S/M-22T
2
--
2
22
SICOM3024P-2GX-24T
2
--
--
24
SICOM3024P-4GE-24S/M
--
4
24
--
SICOM3024P-4GE-16S/M-8T
--
4
16
8
SICOM3024P-4GE-24T
--
4
--
24
SICOM3024P-24S/M
--
--
24
--
SICOM3024P-22S/M-2T
--
--
22
2
SICOM3024P-20S/M-4T
--
--
20
4
SICOM3024P-18S/M-6T
--
--
18
6
SICOM3024P-16S/M-8T
--
--
16
8
SICOM3024P-16S/M
--
--
16
--
SICOM3024P-12S/M-12T
--
--
12
12
SICOM3024P-12S/M-4T
--
--
12
4
SICOM3024P-10S/M-14T
--
--
10
14
SICOM3024P-8S/M-20T
--
--
8
20
SICOM3024P-8S/M-16T
--
--
8
16
SICOM3024P-8S/M
--
--
8
--
SICOM3024P-6S/M-22T
--
--
6
22
SICOM3024P-6S/M-18T
--
--
6
18
SICOM3024P-4S/M-24T
--
--
4
24
SICOM3024P-4S/M-20T
--
--
4
20
SICOM3024P-4S/M-12T
--
--
4
12
SICOM3024P-2S/M-26T
--
--
2
26
SICOM3024P-2S/M-22T
--
--
2
22
SICOM3024P-24T
--
--
--
24

Product Overview
3
SICOM3024P-16T
--
--
--
16
Note:
We reserve the right to amend the product information listed in the table above without notice. To obtain
the latest information, contact our sales or technical support personnel.

Structure and Interface
4
2 Structure and Interface
Caution:
It is recommended to purchase the port dustproof shield (optional) to keep ports clean and ensure switch
performance.
2.1 Front Panel
Figure 1 Front Panel
Table 2 Description of Front Panel
No.
Identifier
Description
(1)
Alarm
Alarm LED
(2)
Run
Running LED
(3)
PWR2
Power 2 LED
(4)
PWR1
Power 1 LED
(5)
Slot4(G1-G4): Speed
Four speed LEDs in Slot 4
(6)
Slot4(G1-G4): Link/ACT
Four connection status LEDs in Slot 4
(7)
Slot1-Slot3(1-8): Speed
Twenty-four Fast Ethernet port speed LEDs in Slot 1, Slot 2 and Slot 3
(8)
Slot1-Slot3(1-8): Link/ACT
Twenty-four Fast Ethernet port connection status LEDs in Slot 1, Slot 2
and Slot 3
(9)
Console
Console port

Structure and Interface
5
2.2 Rear Panel
Figure 2 Rear Panel
Note:
Figure 2 shows the rear panel of SICOM3024P. The layout of Slot 1, Slot 2, and Slot 3 can be A, B, C,
D, E, and the layout of Slot 4 can be F, G, H, I. The actual layout of these slots depends on the
models (as listed in Table 1) you select.
Panel H can provide four 10/100/1000Base-T(X) Ethernet ports or four 10/100Base-T(X) Ethernet
ports. You can find the port type of your device in the software.

Structure and Interface
6
Table 3 Description of Rear Panel
No.
Description
(1)
100Base-FX port
(2)
10/100Base-T(X) Ethernet port, RJ45 connector
(3)
10/100Base-T(X) RJ45 port speed LED (yellow)
(4)
10/100Base-T(X) RJ45 port connection status LED (green)
(5)
1000Base-X, 10/100/1000Base-T(X) SFP slot
(6)
1000Base-X, 10/100/1000Base-T(X) SFP slot connection status LED (green, indicating the status of the
upper slot)
(7)
1000Base-X, 10/100/1000Base-T(X) SFP slot speed LED
(yellow, indicating the speed of the upper slot)
(8)
1000Base-X, 10/100/1000Base-T(X) SFP slot connection status LED (green, indicating the status of the
lower slot)
(9)
1000Base-X, 10/100/1000Base-T(X) SFP slot speed LED
(yellow, indicating the speed of the lower slot)
(10)
Alarm terminal block
(11)
Grounding screw
(12)
Power terminal block
(13)
10/100/1000Base-T(X) Ethernet port, RJ45
connector
10/100Base-T(X) Ethernet port, RJ45 connector
(14)
10/100/1000Base-T(X) RJ45 port speed LED
(yellow)
10/100Base-T(X) RJ45 port speed LED (yellow)
(15)
10/100/1000Base-T(X) RJ45 port connection status
LED (green)
10/100Base-T(X) RJ45 port connection status
LED (green)

Switch Installation
7
3 Switch Installation
3.1 Dimension Drawing
Figure 3 Dimension Drawing (unit: mm)
Caution:
As part of the heat dissipation system, the switch housing becomes hot during operation. Please use
caution when coming in contact and avoid covering the switch housing when the switch is running.
The figures in this chapter are only for reference.

Switch Installation
8
3.2 Mounting Modes and Steps
The series switches support rack mounting by front/rear panel. The following uses mounting by
front panel as an example to describe mounting steps. The steps for mounting by rear panel are
similar to those for mounting by front panel. Before installation, make sure that the following
requirements are met.
1) Environment: temperature (-40℃to 85℃), ambient relative humidity (5% to 95%,
non-condensing)
2) Power requirement: The power input is within the voltage range of the switch.
3) Grounding resistance: <5
4) No direct sunlight, distant from heat source and areas with strong electromagnetic interference.
Installing Mounting Brackets
Figure 4 Mounting Bracket
You can select the screw holes for front or rear panel mounting to install the mounting brackets. If
you select front panel mounting, three mounting positions are available, as indicated by 1, 2, and 3
in the following figure. If there are screws inserted in the screw holes, remove the screws and keep
them for future use.
As shown in the following figure, use three screws to secure two mounting brackets to the switch
respectively.

Switch Installation
9
Figure 5 Installing Mounting Brackets
Mounting
Step 1: Select the mounting position for the device and guarantee adequate space and heat
dissipation for it (dimensions: 440mm×44mm×322.5mm).
Step 2: Move the switch in direction 1 until the screw holes for securing the mounting brackets to
rack posts are in alignment with the corresponding holes in the rack posts. Then use four
screws and supporting captive nuts to secure the mounting brackets to the rack posts.
Figure 6 Mounting by Front Panel
Dismounting
Step 1: Remove the four screws and supporting captive nuts securing the mounting brackets to the
rack posts.
Step 2: Remove the switch from the rack posts. Then unscrew the mounting brackets to complete
dismounting.

Cable Connection
10
4 Cable Connection
4.1 10/100Base-T(X) Ethernet port
10/100Base-T(X) Ethernet port is equipped with RJ45 connector. The port is self-adaptive. It can
automatically configure itself to work in 10M or 100M state, full or half duplex mode. The port can
also adapt to MDI or MDI-X connection automatically. You can connect the port to a terminal or
network device with a straight-through or cross-over cable.
Pins of the 10/100Base-T(X) Ethernet port
Figure 7 shows the pin numbers of the RJ45 port.
8 7 6 5 4 3 2 1
Figure 7 RJ45 Port
Table 4 lists the pin definitions of the 10/100Base-T(X) RJ45 port.
Table 4 Pin Definitions of 10/100Base-T(X) RJ45 Port
Pin
MDI-X Signal
MDI Signal
1
Receive Data+ (RD+)
Transmit Data+ (TD+)
2
Receive Data- (RD-)
Transmit Data- (TD-)
3
Transmit Data+ (TD+)
Receive Data+ (RD+)
6
Transmit Data- (TD-)
Receive Data- (RD-)
4, 5, 7, 8
Unused
Unused
Note:
"+" and "-" indicate level polarities.
Wiring Sequence
Figure 8 Connection Using Straight-through/Cross-over Cable

Cable Connection
11
Note:
The color of the cable for RJ45 connector meets the 568B standard: 1-orange and white, 2-orange,
3-green and white, 4-blue, 5-blue and white, 6-green, 7-brown and white, and 8-brown.
4.2 100Base-FX Port
100Base-FX port is equipped with ST/SC/FC connector, and each port consists of TX (transmit)
port and RX (receive) port, as shown in Figure 9.
Figure 9 shows 100Base-FX port wiring. (The following uses the SC port as an example; ST/FC
wiring method is the same with SC.) To enable data transmission between Switch A and Switch B,
connect the TX (transmit) port of SwitchAto the RX (receive) port of Switch B, and the RX (receive)
port of SwitchA to the TX (transmit) port of Switch B.
Figure 9 Cable Connection of 100Base-FX Port
Caution:
A laser is used to transmit signals in fiber cables. The laser meets the requirements of level 1 laser
products. Routine operation is not harmful to your eyes, but do not look directly at the 100Base-FX
Ethernet port when the switch is powered on.
4.3 10/100/1000Base-T(X) Ethernet Port
10/100/1000Base-T(X) Ethernet port is equipped with RJ45 connector. The port is self-adaptive. It
can automatically configure itself to work in 10M, 100M, or 1000M state, full or half duplex mode.
The port can also adapt to MDI or MDI-X connection automatically. You can connect the port to a
terminal or network device with a straight-through or cross-over cable.
Pin Definition
The following figure shows the pin numbers of the RJ45 port.
8 7 6 5 4 3 2 1
Figure 10 RJ45 Port

Cable Connection
12
The following table lists the pin definitions of the 10/100/1000Base-T(X) RJ45 port.
Table 5 Pin Definitions of 10/100/1000Base-T(X) RJ45 Port
Pin
MDI-X Signal
MDI Signal
1
Transmit/Receive Data (TRD1+)
Transmit/Receive Data (TRD0+)
2
Transmit/Receive Data (TRD1-)
Transmit/Receive Data (TRD0-)
3
Transmit/Receive Data (TRD0+)
Transmit/Receive Data (TRD1+)
4
Transmit/Receive Data (TRD3+)
Transmit/Receive Data (TRD2+)
5
Transmit/Receive Data (TRD3-)
Transmit/Receive Data (TRD2-)
6
Transmit/Receive Data (TRD0-)
Transmit/Receive Data (TRD1-)
7
Transmit/Receive Data (TRD2+)
Transmit/Receive Data (TRD3+)
8
Transmit/Receive Data (TRD2-)
Transmit/Receive Data (TRD3-)
Note:
"+" and "-" indicate level polarities.
Wiring Sequence
Figure 11 Connection Using Straight-through/Cross-over Cable
Note:
The color of the cable for RJ45 connector meets the 568B standard: 1-orange and white, 2-orange,
3-green and white, 4-blue, 5-blue and white, 6-green, 7-brown and white, and 8-brown.

Cable Connection
13
4.4 1000Base-X, 10/100/1000Base-T(X) SFP Slot
1000Base-X, 10/100/1000Base-T(X) SFP slot (Gigabit SFP slot): You can enable data transmission
only after inserting an SFP optical/electrical module into the slot and connecting cable properly. The
following table lists the Gigabit SFP optical/electrical modules (optional) supported by the series
switches.
Table 6 Gigabit SFP Optical/Electrical Modules for SICOM3024P
Model
Interface
MM/SM
Connector
Center
Wavelength
(CWL)
Transmission
Distance
IGSFP-M-SX-LC-850-0.55
1000Base-X port
MM
LC
850nm
0.55km
IGSFP-S-LX-LC-1310-10
1000Base-X port
SM
LC
1310nm
10km
IGSFP-S-LH-LC-1310-40
1000Base-X port
SM
LC
1310nm
40km
IGSFP-S-ZX-LC-1550-80
1000Base-X port
SM
LC
1550nm
80km
IG-FSFP-M-LX-LC-1310-2
100Base-FX port
MM
LC
1310nm
2km
IG-FSFP-S-LX-LC-1310-10
100Base-FX port
SM
LC
1310nm
10km
IGSFP-10/100/1000BASE-
T-RJ45
10/100/1000Base-T(X)
port (self-adaptive)
--
RJ45
connector
--
--
4.4.1 Gigabit SFP Optical Module
Figure 12 Gigabit SFP Optical Module
Gigabit SFP optical module is equipped with LC connector, and each port consists of a TX (transmit)
port and an RX (receive) port. To enable communication between Device A and Device B, connect
the TX (transmit) port of Device A to the RX (receive) port of Device B, and the RX (receive) port of
Device A to the TX (transmit) port of Device B. The following figure shows the cable connection of
the Gigabit SFP optical module.
Figure 13 Cable Connection of Gigabit SFP Optical Module

Cable Connection
14
How to Connect the SFP Optical Module
Insert the SFP optical module into the SFP slot in the switch, and then plug the optical fiber into the
TX port and RX port of the SFP module.
Figure 14 Connecting the Gigabit SFP Optical Module
How to Determine the RX Port and TX Port of Gigabit SFP Optical Module
1. Insert the two connectors in one end of optical fiber into the gigabit SFP module, and those in the
other end of the optical fiber into the SFP module of another switch.
2. View the corresponding port connection status LED in the front panel:
If the LED blinks, the link is connected.
If the LED is off, the link is not connected. This may be caused by incorrect connection of the TX
and RX ports. In this case, swop the two connectors in the one end of the optical fiber.
Caution:
The device uses laser to transmit signals in fibers. The laser meets the requirements of level 1 laser
products. Routine operation is not harmful to your eyes, but do not look directly at the fiber port when
the device is powered on.
If the defined transmission distance of an SFP module is longer than 60km, do not use a short fiber
(<20km) for connection. If such a short fiber is used, the module will be burned.
4.4.2 Gigabit SFP Electrical Module
Figure 15 Gigabit SFP Electrical Module
How to Connect the Gigabit SFP Electrical Module
Insert the SFP electrical module into the SFP slot in the switch, and then plug the RJ45 connector
of the twisted pair into the SFP module.

Cable Connection
15
Figure 16 Connecting the Gigabit SFP Electrical Module
4.5 Console Port
There is a Console port on the front panel of the switch, as shown in Figure 17. Connect the 9-pin
serial port of a PC to the console port of the switch with a DB9-RJ45 console cable. You can
configure, maintain, and manage the switch by running Hyper Terminal in the Windows OS of a
computer.
Figure 17 Console Port
DB9-RJ45 Console Cable
One end of a DB9-RJ45 console cable is the DB9 connector to be inserted into the 9-pin serial port
of a PC, and the other end is crimped RJ45 connector to be inserted into the console port of the
switch.
Figure 18 Wiring Sequence of DB9-RJ45 Console Cable