laerdal SIMETRI 212-55130 User manual

Complete Amputations
for Laerdal SimMan 3G
Laerdal Part No.
212-55130
212-55140
212-55150
212-55160
212-55170
212-55180
User Manual Rev.1.1

LAC-UOM-001, Rev.1.1
i
1. SYSTEM SUMMARY 1
2. INSTALLATION INSTRUCTIONS 2
2.1 SUPPLIES 2
2.2 ENVIRONMENT 2
2.3 PROCEDURE 2
3. USER INSTRUCTIONS 7
3.1 SET UP 7
3.2 START UP 7
3.3 SHUT DOWN 8
3.4 REMOVAL 8
4. MAINTENANCE 10
4.1 SUPPLIES 10
4.2 ENVIRONMENT 10
4.3 PROCEDURE 10
Contents
Contents
Contents
Contents
Contents
Contents
Contents
Contents

LAC-UOM-001, Rev.1.1
1
1. SYSTEM SUMMARY
This document covers the installation, use, and maintenance of the Amputations with Cores (left
side) depicted in Figure 1.
Figure 1. Amputations with Cores
SIMETRI developed hyper-realistic amputated limbs used in the training of traumatic limb injuries,
utilizing the Laerdal SimMan 3G manikin. The amputation's reliability and maintainability are critical
to the objective of maintaining combat emergency response readiness. Steps on how to assemble,
use, and maintain this system are detailed in the sections below.

LAC-UOM-001, Rev.1.1
2
2. INSTALLATION INSTRUCTIONS
2.1 Supplies
The only tool required to install SIMETRI’s Amputations with Cores is the Laerdal Arm Allen Key
(8 mm) provided with the Laerdal SimMan 3G manikin (Figure 2).
Figure 2. Laerdal Arm Allen Key Provided with Laerdal SimMan 3G Manikin
2.2 Environment
Although installation can be done in any environment, a dry and climate-controlled environment is
ideal for installing the Amputation with Cores on the Laerdal SimMan 3G manikin. If not in the ideal
environment, be cautious to avoid getting any fluids or heavy moisture within the system.
2.3 Procedure
In order to install the Amputations with Cores, remove the existing limb from the manikin, following
the removal instructions for the existing limb. If replacing a leg, first unzip the chest skin and lay
the skin open to one side so the ribs are exposed (Figure 3).
Figure 3. Unzip Chest Skin

LAC-UOM-001, Rev.1.1
3
Lift the stomach plate out to access the manikin’s internal cavity (Figure 4).
Figure 4. Open Stomach Plate
Locate the top of the leg pipe, which is secured by a small 2” metal pin that is attached to a yellow
string. Remove the 2” metal pin from the leg shaft, loosening the limb as depicted in Figure 5
below. Keep the 2” metal pin nearby; you will need it for the Leg Amputation attachment.
Figure 5. Remove Metal Leg Pin

LAC-UOM-001, Rev.1.1
4
Insert the SIMETRI Leg Amputation, orienting it so that the metal leg pipe is located closest to the
pelvic region of the manikin (Figure 6). Make sure the hole on the top of the leg pipe can easily
slide into the pelvic opening of the manikin.
Figure 6. Position and Insert Leg Amputation
Once the Leg Amputation is in place, slide the top of the leg pipe directly into the pelvic slot,
aligning both holes into place (Figure 7).
Figure 7. Leg Pipe Orientation into Pelvic Cavity

LAC-UOM-001, Rev.1.1
5
Insert the 2” metal pin attached by a yellow string into the holes, securing both components into
place as illustrated in Figure 8 below.
Figure 8. Secure Metal Pin in Leg Shaft
If replacing an arm, repeat the steps to unzip the chest skin and lift up the chest plate. Use the
Laerdal Arm Allen Key (8mm) (Figure 2) to unbolt the arm connector of the limb and disconnect
the arm (Figure 9).
Figure 9. Unbolt Arm Connection

LAC-UOM-001, Rev.1.1
6
Now orient the Arm Amputation by inserting the black connector inwards into the arm shaft. Once
the black connector is resting inside, insert the hair cotter pin to secure the arm amputation. This
will tighten the black connector in place (Figure 10). Store the round hex (Allen) bolt in a secure
location.
Figure 10. Tighten Bolt to Secure Arm Connector
If you want the Amputation to bleed, locate the connector at the end of the Amputation’s red tubing
and attach it to the connector of the internal Laerdal Blood Line located inside the Laerdal SimMan
3G manikin (Figure 11).
Figure 11. Laerdal SimMan 3G Bleed Ports
Follow Laerdal’s instructions on filling up blood reservoirs and Power On manikin to make blood
flow through the limbs.

LAC-UOM-001, Rev.1.1
7
3. USER INSTRUCTIONS
3.1 Set Up
The only tool required to install the Amputations with Cores is the Laerdal Arm Allen Key.
If you intend to use the amputation bleeding capabilities, you must perform the following step
before turning the manikin’s power on. Connect the amputation’s red tubing to the end of the
internal Laerdal Blood Line located inside the Laerdal SimMan 3G manikin. This will allow
simulated blood to course through the amputations once the system is turned on.
If you don’t intend to use the amputation’s bleed functions, you may power the manikin’s system
on without attaching the tubes.
3.2 Start Up
Plug the power supply into a wall outlet and connect the power cable to the power inlet of the
manikin’s power panel. Activate the “On” button on the Power Panel located on the right side of
the manikin by the waistline (Figure 12).
Figure 12. Laerdal SimMan 3G Power Panel

LAC-UOM-001, Rev.1.1
8
The fluid bottle, filled with blood fluid per Laerdal’s instructions, needs to be attached to the Bleed
Inlet of the Fluid Fill Panel located on the right side of the manikin (Figure 13). This allows for the
internal reservoirs filled with simulated blood to be pumped through the tubing system so that blood
can actively bleed through the wounds that are attached. Follow Laerdal’s instructions on how to
run the manikin with external blood.
Figure 13. Laerdal SimMan 3G Fluid Fill Panel
3.3 Shut Down
When the Laerdal manikin’s system is shut down, the microprocessor is also powered off
automatically.
3.4 Removal
Making sure the Laerdal manikin’s system is turned off, please use the following steps to remove
the Leg Amputation from the manikin.
1. Unzip and remove skin from chest
2. Reposition abdomen to provide access to internal components.
3. Disconnect the red line from the manikin and the amputated leg by twisting the white
connector.
4. Locate the metal pin and pull it out of the pelvic slot, thus loosening the leg pipe from