Lampo IP67 LED Colour changer User manual

M
M
MI
I
IN
N
NI
I
I
C
C
CH
H
HI
I
IC
C
C
L
L
LE
E
ED
D
D
r
r
rg
g
gb
b
b
I
I
IP
P
P6
6
67
7
7
L
L
LE
E
ED
D
D
c
c
co
o
ol
l
lo
o
ou
u
ur
r
r
c
c
ch
h
ha
a
an
n
ng
g
ge
e
er
r
r
USER’ S MANUAL release 2.0
This manual must be considered an integral part of the projector.

1
BEFORE CONNECTING AND USING THE PROJECTOR, IT IS IMPORTANT TO READ CAREFULLY ALL THE
INSTRUCTIONS IN THIS MANUAL.
QUALIFIED PERSONNEL ONLY, IN COMPLIANCE WITH ALL THE SECURITY LAWS, CAN DO THE
INSTALLATION, THE MAINTENANCE AND THE UTILISATION OF THIS PROJECTOR.
BEFORE CONNECTING THE PROJECTOR, MAKE SURE THAT THE FREQUENCY AND THE VOLTAGE
VALUES ARE SUITABLE AS SPECIFIED ON THE PROJECTOR.
FOR ANY DOUBT, CONTACT YOUR SUPPLIER OR SEND AN E-MAIL TO:
[email protected]
LED RADIATION, DO NOT STARE INTO BEAM, CLASS 2 LED PER IEC 60825-1.
For additional information on these led devices with regard to the IEC 60825-1 standard, contact CREE.
SOLID: Dust-tight
WATER: Protected against immersion effects
Suitable for direct mounting on normally flammable surfaces
Minimum distance from lighted objects (0.3 meters)
Rated maximum ambient temperature (indoor with ventilation)
Replace any cracked protective shield, dichroic filter or lens
Index
Dimensions and weight ---------------------------------------------------------------------------------- page 2
Technical data --------------------------------------------------------------------------------------------- page 2
Storage ------------------------------------------------------------------------------------------------------ page 2
Admissible environmental conditions ----------------------------------------------------------------- page 2
Installation ------------------------------------------------------------------------------------------------- page 2
Connection -------------------------------------------------------------------------------------------------- page 3
Cable wiring ------------------------------------------------------------------------------------------------ page 3
Optical specifications ------------------------------------------------------------------------------------- page 4
Lenses ------------------------------------------------------------------------------------------------------- page 4
Power supply ---------------------------------------------------------------------------------------------- page 4
Spare parts ------------------------------------------------------------------------------------------------ page 4

2
Dimensions & weight
In-built RJ45 female connector, PG9 cable clamp
Technical data
- Aluminium body
- IP67 protection rate
- Plastic house
- Walk over
ATTENTION!!!
Connect the projector only to dedicated power unit.
Up to 20 meters total connection cable (series connection with UTP straight patch cables).
The power unit (LED POWER RGB) can drive up to 10 Mini Chic Led RGB.
Storage
The projector, in its original packing, must be kept in covered, dry areas with a temperature between –10°C and +50°C.
Attention, the projector will be damaged during the unpacking.
Admissible environmental conditions
The projector was engineered and produced to function in outdoor areas with an air temperature ranging between -20° and
+30°C and with a humidity level between 30 and 90%.
When choosing the installation, please make sure that the device is not exposed to extreme heat or in small area.
If the projector is installed in hot area, led life is decreased.
Installation
The projector is designed for in-ground installation. It is possible to walk on it.
The stainless steel ring has a 4mm maximum thickness.
Put sand and dredged gravel under the projector to ease the water drainage.

3
Connection
This series of fixtures based on three led’s board, has now a built-in RJ45 female connector
This solution allows the user to get an easier, faster and safer connection.
Connect the projectors to the power unit with standard CAT.5 UTP STRAIGHT PATCH CABLE, and special HUB RJ45.
Example with three fixtures: (3 fixtures, 1 led power, 2 Hub RJ45, 5 UTP straight patch cable)
ATTENTION!!!
Don’t plug in or out the connector from the fixture or from the led power when is connected to the main
power. This non-observance will damage permanently the fixtures and the led power.
Cable wiring
568B SPECIFICATION – CABLE MANUFACTURING INSTRUCTION
PIN ORDER OF THE PLUG

4
Optical specifications
- 3 LEDs RGB high power 1.2W Xlamp by CREE
- Approx. 10 years life (continued use)
- Colour mixing system R.G.B.
- Adjustable intensity of each colour: Red, Green, Blue
Lenses
There are three types of lenses, see the draw to identify the lense and the beam angle.
Power supply
Disconnect mains power supply before any operations.
Do not power the projector with a dimmer circuit
When in doubt, consult a qualified electrician.
Connect the Mini Chic to the power unit (LED POWER RGB) or to the other projectors, 10 max.
Spare parts
When ordering spare parts for the projector remember to mention the model and serial number of the projector.
Call your area dealer or feel free to contact the manufacturer for any additional assistance.
The improper use of this projector, cancel the guarantee and our responsibility. All the information have been written and driven with
extreme care; however, we do not engage us any responsibility for contingent errors or omissions. We reserve the right to modify and/ or
improve our product as we retain necessary, without subsequent warning or notice. It is forbidden any complete or partial reproduction of
this handbook, if not expressly authorized.