Lanner electronics EM-535 Series User manual

EM-535 Series
5.25” Embedded SBC
with NS GeodeTM CPU,
LCD/VGA,TV,Sound,LAN,SSD Socket,
PCMCIA/Compact Flash /GPS

COPYRIGHT ©
This document is a copyright of the original manufacturer, 2000. The original manufacturer reserves the
right to make improvements to the product(s) described in this manual at any time without notice. This
manual may not, in whole or in part, be photocopied, reproduced, transcribed, translated, or transmitted in
whatever form without the written consent of the manufacturer, except for copies retained by the purchaser
for backup purposes. All rights are reserved.
TRADEMARKS
GeodeTM is a registered trademark of NS Corporation.
The following are trademarks or registered trademarks of their respective companies: IBM, Intel, AMD,
Cyrix,NS, Award, AMI, Microsoft, Windows, Windows NT, Novell, SCO, PC/104, PICMG, ALI, UMC,
SMC, Winbond. Products mentioned in this manual are mentioned for identification purposes only. All
names of products or services appearing in this manual are the trademarks or registered trademarks of
their respective organizations and companies.
ãCopyright 2000
Ver. No. V1.0
LEI-UM-EM535-000
Date : 2000/05/06

TABLE OF CONTENTS
CHAPTER 1INTRODUCTION 1
1.1 SPECIFICATION 2
1.2 PACKING CHECK LIST 3
CHAPTER 2JUMPER SETTINGS AND CONNECTORS 4
2.1 BOARD OUTLINE OF EM-535 4
2.2 JUMPER SETTING OVERVIEW 6
2.3 INSTALLING THE DIMM MODULE 6
2.4 JUMPER LOCATION FOR EM-535 7
2.5 JUMPER SETTINGS SUMMARY FOR EM-535 8
2.6 JUMPER SETTINGS FOR EM-535 9
2.7 I/O CONNECTORS LOCATION FOR EM-535 13
2.8 I/O CONNECTORS SUMMARY FOR EM-535 15
2.9 I/O CONNECTORS DESCRIPTION 16
CHAPTER 3AWARD BIOS SETUP 30
3.1 RUNNING AWARD BIOS 30
3.2 CMOS SETUP UTILITY 31
3.3 STANDARD CMOS SETUP 32
3.4 BIOS FEATURES SETUP 35
3.5 CHIPSET FEATURES SETUP 38
3.6 POWER MANAGEMENT SETUP 39
3.7 PNP/PCI CONFIGURATION 41
3.8 LOAD BIOS DEFAULTS 43
3.9 LOAD SETUP DEFAULTS 43
3.10 INTEGRATED PERIPHERALS 44
3.11 SUPERVISOR / USER PASSWORD 46
3.12 IDE HDD AUTO DETECTION 46
3.13 Save & Exit Setup 47
3.14 EXIT WITHOUT SAVING 47

TABLE OF CONTENTS
CHAPTER 4 BIOS UPDATED 48
4.1 BIOS UPDATED 48
4.2 AWARD BIOS FLASH INSTRUCTIONS 48
CHAPTER 5 DRIVERS SUPPORT 50
5.1 USE YOUR DRIVER CD-ROM 50
5.2 FILE DIRECTORY 50
APPENDIX A HOW TO USE WATCH-DOG TIMER 51
APPENDIX B TECHNICAL REFERENCE 52
GLOSSARY 54
TERMS AND CONDITIONS
RMA SERVICE REQUEST FORM

EM-535 / 1
CHAPTER 1.
INTRODUCTION
The new EM-535 NS Geode™ GXm embedded SBC is a great choice for any multimedia applications.
The NS Geode™ processor and its companion CX5530 chipset support up to 256MB memory and
provide full functionality and performance to meet your needs.
EM-535 features Flat Panel/CRT display functions that support resolutions and color depths up to
1024x768 at 64K colors, TV-output for NTSC and PAL modes, and sound functions. And the Realtek
8139 chip provides PCI Fast Ethernet for network connectivity.
EM-535 has many expansion options, including one PCI expansion connector, one CompacatFlash
socket, one PCMCIA socket and a socket for DiskOnChip 2000. Other on-board features include one
PCI Enhanced IDE ports for up to four IDE and Ultra DMA-33 devices, four 16550 serial ports, two
multi-mode parallel ports, two USB ports and one IrDA interface.
For any all-in-one boards like the EM535, most other similar products require customers to install many
cables and adapters for various I/O’s like VGA, USB, Audio, serial and parallel ports. That would cause
messy and difficult tasks for users to implement on such a tiny and compact board area.
However, EM-535 does provide a great solution to save our customers from such headaches. With a
pre-defined and pre-installed connector setup, it not only provides a very neat signal interface but also
offers a vibration proof advantage. In turn, our customers will have a more solid foundation for their
products and projects based upon EM-535.

INTRODUCTION
EM-535 / 2
1.1 SPECIFICATION
oProcessor : NS Geode GXLV-200/233/266 MHz ( on-board ) CPU on-board
oChipset : NS GX5530, Realtek RTL8139, Winbond W83977F / W83877TF I/O chipset,
RICOH R5C476II PCMCIA Bridge, CHRONTEL CH7003B TV Encoder,
AD1819A Audio CODEC
oSystem Memory / RAM : One DIMM socket, support up to 128MB of SDRAM
oVGA/LCD Controller : NS GX5530, shared memory 2MB,
resolution up to 1024 x 768 @ 64K colors
oTV Output NTSC/PAL mode, support S-Video/Composite/R-G-B output
oSound Output Built-in sound functions, include Mic-in/Line-in/Speaker-out
oEthernet Controller : On board Realtek RTL8139, support 10/100 Base-T interface
oSSD interface : Reserved socket for DiskOnChip from M-System, support up to 144 MB flash
memory disk
oGPS connector Reserved header for GPS kit
oPCMCIA Socket One PCMCIA socket, support Hot-plug function, Type-I/II
oCompactFlash Socket : One Compact Flash socket, support Hot-plug function, Type-I/II.
oExpansion Bus Built-in one PCI expansion slot
oIDE Interface : One PCI IDE port, support up to two IDE devices. Supports PIO mode 4 and
Bus Master. Also supports Multi-word DMA and Ultra DMA/33.
oFloppy Drive Interface : One FDD port , support up to two floppy devices
oSerial Port : Four COM ports , Three RS-232 and one RS-232 / 422 / 485
oParallel Port : Two Multi-mode parallel port ( SPP/EPP/ECP )
oKeyboard/Mouse
connector One 6-pin mini-DIM PS/2 keyboard/mouse connector on-board.
oUniversal Serial Bus Support 2 USB ports
oIR Interface Supports one IrDA header
oWatchdog Timer Software 16 level time-out intervals (0/2/4
/6/8/10/12/14/16/18/20/22/24/26/28/30
sec.)
oRTC : Internal RTC with Li battery
oBIOS : 256KB Award license BIOS
oPower management :
I/O peripheral devices support power saving and doze/standby/suspend modes.
APM 1.2 compliant.
oPower Connector : On-board ATX power connector, with one ATX/AT/HDD power connector
optional
oOperating Temperature : 0°C ~ 60°C
oStorage Temperature : -20°C ~ 70°C
oHumidity : 5% ~ 95% RH, non-condensing
oDimensions : 203 x 146 mm ( 8” x 5 3/4” inches ) +/-0.5mm
oNet weight : 350 g ( 0.770 pounds )
oEMI/EMS EN 50081-1/1994>EN 55022/1997>EN 61000-3-2/1995
>EN 61000-3-3/1995, EN 50082-1/1994>IEC 1000-4-2/1995,
IEC 1000-4-3/1995, IEC 1000-4-4/1995

INTRODUCTION
EM-535 / 3
Ordering Information
Function
Model VGA/LCD SSD GPS Sound LAN TV Compact Flash PCMCIA PCI
EM-535A nnnnnnnn
EM-535Bnnnnnnn
EM-535C nnnnnnn
EM-535Dnnnnnn
EM-535Ennnnn
EM-535Fnnnn
Note:
EM-535B/D/E/F are not standard products , if you want these please contact your
supplier.
1.2 PACKING CHECK LIST
Before you begin to install your card, please make sure that you received the following materials as listed
below:
Item Qty Remark
EM-535 1 pc. Embedded Single Board Computer
Keyboard / Mouse “Y” shape adapter cable 1 set6 pin Min-
Din to one 5 pin keyboard connector & one PS/2
mouse connector
Hard Disk Cable 1 pc. 40p to 40p standard header flat ribbon cable
FDD Cable 1 pc 34p to 34p standard header flat ribbon cable
COM port connector 1 pc 10 pin 2.54mm for 9 pin D-Sub, two COM port , 50cm
TV adapter cable 1 pc 6 pin Min-Din to one 4 pin female Min-
Din & one RCA female
connectors, (20cm)
CD-ROM 1 pc. Drivers
User‘s manual 1 pc. EM-535

EM-535 / 4
CHAPTER 2.
JUMPER SETTINGS AND CONNECTORS
The figure belowshows the jumpers and connectors location on the EM-535:
2.1 BOARD OUTLINE OF EM-535
SPEAK1
LINE IN
ISP1
IDE1
IDE2
FDC1
Cyrix
chipset
KM1
KM2
LPT1
MC1
JP1
TWD1
JP3
GPS1
LCD1
LPT2
PS2
SDOC1
PCI1
FAN1
PLRS1
COM4 COM3 COM2
PS4
CMOS1
JP4
IRDA1.
JP2 SC2T2 SC2T1
SLCD1
.LAN
1
13
14
1
5
VGA1
COM1
9
6
1
5
11
15
USBKM1
LPT1
LINE IN SPEAK1 MCI
14
25

JUMPER SETTING AND CONNECTORS
EM-535 / 5
PM1
CF
REAR SIDE

EM-535 / 6
2.2 JUMPER SETTING OVERVIEW
In order to select the operation modes of your system, configure and set the jumpers on the your SBC
to match the need of your application. To set a jumper, a black plastic cap containing metal contacts
is placed over the jumper pins as designated by the required configuration as listed in this section. A
jumper is said to be “ on ” or “ 1-2 ” when the black cap has been placed on two of its pins, as show in
the figure below:
A pair of needle-nose pliers is recommended when working with jumpers. If you have any doubts
about the best hardware configuration for your application, contact your local sales representative
before you make any changes. In general, you simply need a standard cable to make most
connections.
2.3 INSTALLING THE DIMM MODULE:
A DIMM module simply snaps into a socket on the system board. Pin1 of the DIMM module must
correspond with Pin1 of the socket.
1.Position the DIMM above the socket with the “notch” in the module aligned with the
“key” on the socket.
2. Seat the module at a 90 angle into the bank. Make sure it is completely seated. Tilt
the module upright until it locks in place in the socket.
Pin1
Notch
Key

JUMPER SETTINGS AND CONNECTORS
EM-535 / 7
2.4 JUMPER LOCATION FOR EM-535
Cyrix
FW82371AB
chipset
375
Slcd1
Sdoc1 JP1
Twd1
JP3
JP2
JP4
CMOS1
3
1
1
1
2
9
10
3
1
4
9
12
9
12
1
4
Sc2t2
Sc2t1
1
5
2
6
1
2
1
2
3

JUMPER SETTINGS AND CONNECTORS
EM-535 / 8
2.5 JUMPER SETTINGS SUMMARY FOR EM-535
LOCATION FUNCTION
Sdoc1 Select DiskOnChip(Flash Disk) Address
Slcd1 Select Panel Voltage
CMOS1 Clear CMOS Data
JP1 Default Setting
JP2 Select COM2 Enabled/ Disable
JP3 Default Setting
JP4 ATX Power sw pin Header
Twd1 Select Software Watch-Dog Timer
Sc2t1/Sc2t2 Select COM2 Type

JUMPER SETTINGS AND CONNECTORS
EM-535 / 9
2.6 JUMPER SETTINGS OF EM-535
lSdoc1 : Select DiskOnChip ( Flash Disk ) Address
Flash Disk Address Sdoc1
CC00H~CDFFH 1-2,9-10
D000H~D1FFH 3-4,7-8
D400h~D5FFH 3-4,9-10
D800H~D9FFH 5-6,7-8
DC00H~DDFFH 5-6,9-10
lSlcd1 : Select Panel Voltage
Panel Voltage Vlcd1
3.3V ( Default ) 2-3
5V 1-2
Default :
Sdoc1
1
3
5
7
9
2
4
6
8
10
CC00H~CDFFH
D000H~D1FFH
Sdoc1
D400H~D5FFH
D800H~D9FFH
DC00H~DDFFH
1
3
5
7
9
2
4
6
8
10
Slcd1
5V
3.3V
3
2
1
Slcd1
3
2
1
Default :
Slcd1
3
2
1

JUMPER SETTINGS AND CONNECTORS
EM-535 / 10
lCMOS1 : Clear CMOS Data
Description CMOS1
Normal (Default) 1-2
Clear CMOS 2-3
lJP1 : Default Setting （ 1-2 ）
lJP2 ： Select COM2 Enable / Disable
COM2 Enable ：（ 5-9, 6-10, 7-11, 8-12 ） ð Default
COM2 Disable ：（ 1-5, 2-6, 3-7, 4-8 ） ð Use GPS
lJP3 ： Default Setting （ 1-2 ）
Clear CMOS
Normal (Default)
CMOS1
3
2
1
CMOS1
3
2
1
Default :
JP3
3 1
Default
:12
11
10
9
4
3
2
1
JP2
Default :
JP1
3 1

JUMPER SETTINGS AND CONNECTORS
EM-535 / 11
lJP4 ： ATX Power Sw Pin Header
lTwd1 ： Select Software Watch-Dog Timer
Software Watch-Dog Timer Twd1
0/2/4/6/8/10/12/14/16/18/20/22/24/26/28/30 1-2
0/8/16/24/32/40/48/56/64/72/80/88/96/104/112/120 2-3
Default :
JP4
1
2
Default :
Twd1
3 1

JUMPER SETTINGS AND CONNECTORS
EM-535 / 12
lSc2t1/Sc2t2 : Select COM2 Type
COM2 Type Sc2t1 Sc2t2
RS-232 (Default) 1-21-5,2-6,3-7,4-8
RS-422 3-45-9,6-10,7-11,8-12
RS-485 5-65-9,6-10,7-11,8-12
Default :
Sc2t1
5 6
2
1 2
9
12
1
4
Sc2t2
RS-422
RS-485
RS-232
Sc2t1 9
12
2
6
1
5
Sc2t2
1
4

JUMPER SETTINGS AND CONNECTORS
EM-535 / 13
2.7 I/O CONNECTOR LOCATION FOR EM-535
Cyrix
chipset
KM1
KM2
LPT1
MC1
GPS1
LCD1
LPT2
PS2
SDOC1
PCI
FAN1
PLRS1
COM4 COM3 COM2
PS4
IrDA1.
SPEAK1
LINE IN
ISP1
8 1
1
26
1
25
1
12
40
IDE1
2
40
IDE2
2
34
FDC1
2
1
5
1
7
9
1
10
2
10 1
1 3
LAN
1
13
14
1
5
VGA1
COM1
9
6
1
5
11
15
USBKM1
LPT1
LINE IN SPEAK1 MCI
14
25

JUMPER SETTINGS AND CONNECTORS
EM-535 / 14
PM1
CF
REAR SIDE