Lanner electronics EM-9560 Series User manual

EM-9560 Series
5.25” Intel ULV Celeron Embedded SBC
with onboard memory, VGA, LCD, Audio
CF, DOC, LAN, USB 2.0
and PC/104+ expansion
USER'S MANUAL

COPYRIGHT©
This document is a copyright of the original manufacturer, 2005. The original manufacturer reserves
the rights to make improvement and/or modification to the product described in this manual at any
time without further notice. This manual may not, in whole or in part, be photocopied, reproduced,
transcribed, translated, or transmitted in whatever form without the written consent of the
manufacturer, except for copies retained by the purchaser for backup purposes. All rights are
reserved.
TRADEMARKS
The following are trademarks or registered trademarks of their respective companies: IBM, Intel, AMD,
Award, AMI, Microsoft, Windows, Windows NT, Novell, SCO, PC/104+, PICMG, ALI, UMC, VIA, S3,
Realtek, SMC and Winbond. Products mentioned in this manual are mentioned for identification
purposes only. All names of products or services appearing in this manual are the trademarks or
registered trademarks of their respective organizations and companies.
Copyright 2005
Version: 1.0
Date: 2005/10/07

TABLE OF CONTENTS
CHAPTER 1 INTRODUCTION...........................................................................................................................................1
1.1 INTRODUCTION................................................................................................................................................................1
1.2 FEATURES........................................................................................................................................................................1
1.3 SPECIFICATION.................................................................................................................................................................2
1.4 UNPACK YOUR EM-9560 SERIES.....................................................................................................................................3
1.5 BOARD LAYOUT ..............................................................................................................................................................4
CHAPTER 2 INSTALLATION.............................................................................................................................................5
2.1 SYSTEM MEMORY INSTALLATION....................................................................................................................................5
2.2 JUMPER SETTINGS AND CONNECTORS .............................................................................................................................6
2.2.1 Board Outline ..........................................................................................................................................................6
2.2.2 Jumper Settings Summary........................................................................................................................................7
2.2.3 I/O Connectors Summary.......................................................................................................................................10
CHAPTER 3 BIOS SETUP .................................................................................................................................................25
3.1 RUNNING AWARD BIOS..............................................................................................................................................25
3.2 CMOS SETUP UTILITY..................................................................................................................................................26
3.3 STANDARD CMOS SETUP .............................................................................................................................................28
3.4 BIOS FEATURES SETUP.................................................................................................................................................31
3.5 CHIPSET FEATURES SETUP.............................................................................................................................................33
3.6 INTEGRATED PERIPHERALS............................................................................................................................................36
3.7 POWER MANAGEMENT SETUP .......................................................................................................................................38
3.8 PNP/PCI CONFIGURATION.............................................................................................................................................40
3.9 PC HEALTH STATUS (OPTIONAL)...................................................................................................................................42
3.10 LOAD OPTIMIZED DEFAULTS .......................................................................................................................................43
3.11 SET SUPERVISOR / USER PASSWORD............................................................................................................................44
3.12 SAVE & EXIT SETUP ....................................................................................................................................................45
3.13 EXIT WITHOUT SAVING ...............................................................................................................................................46
CHAPTER 4 DRIVERS SUPPORT ...................................................................................................................................47
4.1 USE YOUR DRIVER CD-ROM .......................................................................................................................................47
4.2 FILE DIRECTORY............................................................................................................................................................47
APPENDIXA. WATCH-DOG TIMER...............................................................................................................................48
RMA SERVICE REQUEST FORM...................................................................................................................................50

Chapter 1 Introduction
Chapter 1 Introduction
1.1 Introduction
The EM-9560 is an embedded SBC offering multi-I/O flexibility and full multi-media functionality support. It
also supports onboard system memory, versatile interfaces, storages and PC/104&PC/104+ expansion
slots to fulfill the needs from different industry applications. Complying with the industry standard form
factor – EBX (5.75” x 8” inches), user can minimize the system conflicts and configuration problems.
EM-9560 offers two computing power options: Intel Celeron Ultra Low Voltage 400MHz and 650MHz. Intel
Celeron Ultra Low Voltage 400MHz is designed especially for fan-less requirement to enable better MTBF.
As an x86 architecture, the platform supports prevail operating systems such as Windows
95/98SE/XP/2000/NT and Linux. Your previous investment on these operating systems is, thus, protected in
the future.
VIA Twister-T chipset is the mid-end position of VIA chipsets. It supports 2D/3D Video Accelerator by
integrating S3 Savage4. It also supports 36-bit TFT LCD and 2 channel (2 x 18-bit) LVDS. EM-9560 is able
to compatible with the most coming bigger size industrial and commercial LCDs. By enabling VRAM, the
system can further cut its cost and while maintains its speed. EM-9560 uses onboard 128MB SDRAM and
one SODIMM to limit its board height and supports PC 133/PC 100.
There are three storage options in EM-9560 design. One is EIDE, and one is DOC socket and the other is
CF type II. EIDE supports two IDE devices. EM-9560 offers 2 IDE box header options to fulfill flexible hard
disk placement in system design. 40-pin box header focuses on 3.5” hard disk, 44-pin box header mainly
couples itself with 2.5” hard disk. DOC socket can support M-System DiskOnModule flash memory module.
Regarding to CF II socket, system can further cut its whole size when using popular large volume CF II form
factor SSD.
EM-9560 embodies the following I/O: 1 x 10/100Mbps LAN, 1 x FDD, 4 x COM, 1 x LPT, Keyboard & Mouse,
4 x USB 2.0, 1 x IrDA and 8 x DIO. Expansion slots include PC/104 and PC/104+. Power supply complies
with AT and ATX. Watchdog timer is 256-level.
As an industrial PC embedded card, EM-9560’s operating temperature is ranging from 0°C to 60°C. All
these numerous features provide an ideal price/performance solution for commercial and industrial
applications where stability and reliability are essential.
1.2 Features
 Onboard Intel ULV Celeron 400MHz Fan-less or 650MHz CPU onboard
 VIA VT8606 North Bridge and VT82C686B South Bridge
 Onboard 128MB SDRAM and 1 x SODIMM PC-133 up to 512MB memory module
 Award Flash BIOS
 S3 Savage 4 2D/3D video Accelerator
 VGA, 36-bit TTL LCD and 2x18-bit LVDS
 10/100 Base-T Fast Ethernet
 Support DiskOnChip and CF Type I/II
 PC/104 and PC/104 Plus + expansion slots
 one IDE DMA 33/66/100 and one IDE DMA 33
 1xLAN, 1xFDD, 4xCOM, 1xLPT, 1xPS2 KB/MS, 4xUSB and 1xIrDA
 Watchdog Timer
 8 bits Digital I/O
 AT/ATX power function
1
User’s Manual

Chapter 1 Introduction
1.3 Specification
EM-9560 Series
Processor : 1>
2> Ultra-Low-Voltage Intel Celeron 400MHz Fan-less or 650MHz on board CPU Fan connector: 2x1x2.54mm wafer ( for 650 MHz CPU )
L2 Cache : 1> 256KB in CPU
Chipset : 1> VIA VT8606 (North) & VT82C686B (South)
BIOS : 1> 256KB Award BIOS
System Memory : 1>
Onboard 128MB SDRAM system memory and one 144 pins SoDIMM socket up to 512MB SDRAM
VGA & LCD : 1>
2>
3>
4>
Chip: VT8606 integrated S3 ProSavage 4, AGP 4X Graphics support
36 bit TFT & 2 channels (2x18-bit) LVDS LCD
VRAM: Support 8/ 16/ 32MB memory (shared)
VGA Connector: 2x6 2.0mm pin-header
LCD Connector: TTL - 2x25x1.0 mm box-header; LVDS - 2x15x1.0 mm box-header
LCD Inverter Port : 1> Connector: 1x5x2.54 mm wafer
Audio : 1> Optional module for AC 97 Codec, Supports Mic-in, Line-in, Line-out
Ethernet : 1>
2> Chip: Realtek RTL8139C + Connector: 2x6x2.0 mm pin-header
Solid State Disk : 1>
2> 1xCF Socket, support type I/II ATA Mode Compact Flash card 1xDOC socket, support M-System DiskOnChip 2000 Flash memory module.
Expansion Bus : 1> Connector: PC/104+ and PC/104 female
Serial Port (Four) : 1>
2> COM Setting: 3xRS-232; 1xRS-232/422/485 setting by jumper Connector: 2x20x2.0 mm box-header
Parallel Port : 1>
2> Multi-mode: SPP/ EPP/ ECP
Connector: 2x13x2.0 mm box -header
IDE interface : 1>
2> Connector: 2x20x2.54 mm box –header support Ultra DMA100 Connector: 2x22x2.0 mm box –header
FDD interface : 1> Connector: 2x17x2.0 mm box –header
Universal Serial Bus : 1> Connector: Two 2x5x2.0 mm pin-header
Keyboard / Mouse : 1> Connector: 6-pin mini-DIN support PS/2 Keyboard and PS/2 Mouse
IrDA : 1>
2> Share with COM 2 Connector: 1x5x2.0 mm pin-header
RTC : 1> 3V Li battery in holder
System Indicator : 1>
2> H/W Reset, Power LED, HDD LED & System alarm speaker Connector: 1x11x2.54 mm pin header
Watchdog Timer : 1> 0~255 Sec, 256 level time out intervals (by Software)
Power Source : 1> 7 pin EBX power connetor and 4pin small header for –5V and –12V input
Dimension : 1> 203 mm x 146 mm ( 8.0” x 5.7” )
Hardware Monitor : 1> Super I/O controller integrated
Operating Temp : 1> 0°C to 60°C (32°F to 140°F)
Humidity : 1> 5% to 95% RH, non-condensing
Ordering Information : 1> EM-9560A: SBC with Intel ULV C400 CPU, Fan-less, USB2.0
2> EM-9560B: SBC with Intel ULV C650 CPU, USB2.0
3> EM-9560C: SBC with Intel ULV C400 CPU, Fan-less, USB 1.1
4> EM-9560D: SBC with Intel ULV C650 CPU, USB 1.1
2 User’s Manual

Chapter 1 Introduction
1.4 Unpack your EM-9560 Series
Before you begin to install your card, please make sure that you received the following materials as listed below:
Standard Packing:
 EM-9560 x 1 pc Embedded Single Board Computer
 Driver Utility CD-ROM x 1 pc Drivers & Utilities
 User's Manual x 1 pc This User's Manual
Note: All Option Kits are to be purchased separately
Option: EM-9560CB
 USB Y Cable x 1 pc 0800100100013 USB Y Cable 2x5P 2.0mm with key P3,8 L:100mm
 FDD Cable x 1 pc 0800100340003 FDD 34P 2.0mm TO 34P 2.54mm
 IDE Cable x 2 pc 0800100400004 ATA100 40P IDE with key P20
 IDE Cable x 1 pc 080019D440001 IDE 40Px2 TO 44P with key P20
 VGA Cable x 1 pc 0800200150001 VGA 12P TO 15P 2.0mm with key P8 L:100mm
 LAN Cable x 1 pc 0800400120001 LAN 2x6P 2.0mm with key P4 L:100mm
 Power Cable x 1 pc 0800800120002 EBX (7PIN) TO AT P8/P9(12 PIN)
 KB/MS Y Cable x 1 pc 0801895080001 K/M Y CABLE 8P Header to PS2
 LPT Cable x 1 pc 0802100250001 25P D-SUB TO 26P 2.0mm with key P26 L:100mm
 COM Port Cable x 1 pc 080279D400001 40P TO 9P DSUB 公x4 with key P40
 Power Cable x 1 pc 080W142003001 7PEBX+4P PH2.0+3P PH2.0 Header L:300mm
3
User’s Manual

Chapter 1 Introduction
1.5 Board Layout
4 User’s Manual

Chapter 2 Installation
Chapter 2 Installation
2.1 System Memory Installation
Step 1: Insert the RAM module into the SODIMM socket
Step 2: Press Module down till clip hold.
5
User’s Manual

Chapter 2 Installation
2.2 Jumper Settings and Connectors2.2 Jumper Settings and Connectors
2.2.1 Board Outline2.2.1 Board Outline
USBF2 USBF2
PSW1 PSW1
USBF1 USBF1
LPTC1
PLRS1
IRDA1 IRDA1
PKMB1 PKMB1
FDCC1 J8
INVER1
VGAB1
FAN1
PS7M1
J3 J4 J5
LANI1
J2
ATXE1
PS4W1
J1
DIMMB1
LVDSC1
LCD1
SDOC1
SC2T1
SC2T2
SRIV1
DIOB1
J6
PCON1
SRIV2
DOC1
COME1
IDEB1
IDEA1
CPU
6 User’s Manual

Chapter 2 Installation
2.2.2 Jumper Settings Summary
LOCATION FUNCTION
J1 Select Panel Voltage
J2 Reserve for AC97 Header
J3 Reserve for inverter
J4 Reserve for inverter
J5 Reserve for inverter
J6 Select CF Card Voltage
J8 Clear CMOS Data
SRIV1 / SRIV2 Select COM port pin 9 Type
SC2T1 / SC2T2 Select COM2 Type
SDOC1 Select Flash Disk Address
 J1:Select Panel Voltage
3
2
1
1
3
5
2
4
6
1
3
5
2
4
6
Voltage J1
+5V ( Default ) 1-3, 2-4
+3.3V 3-5, 4-6
J1
 J6 : CF Power Select
Voltage J6
+ 5 V (Default) 1-3, 2-4
+ 3.3 V 3-5, 4-6
J6
J8
J6
 J8 : Clear CMOS Data
Description J8
Normal (Default) 1-2
Clear CMOS 2-3 J1
J8
7
User’s Manual

Chapter 2 Installation
 SRIV1,SRIV2:Select COM port pin 9 Type
1
2
3
4
9
10
11
12
1
2
3
 SC2T1/SC2T2: Select COM2 Type
COM2 TYPE SC2T1 SC2T2
RS-232 (Default) 1-2 1-5,2-6,3-7,4-8
RS-422 3-4 5-9,6-10,7-11,8-12
RS-485 5-6 5-9,6-10,7-11,8-12
Pin 9 Type SRIV1 SRIV2
RI (Default) 1-5,2-6,3-7,4-8 open
+5V 5-9,6-10,7-11,8-12 1-2
+12V 5-9,6-10,7-11,8-12 2-3
SC2T2
SRIV2
SRIV1
SC2T1
SRIV1
SRIV2
5
3
1
6
4
2
SC2T1 SC2T2 4
3
2
1
12
11
10
9
Default :
5
3
1
12
11
10
9
SC2T2
4
3
2
1
6
4
2
SC2T1
RS-232
RS-485
RS-422
8 User’s Manual

Chapter 2 Installation
SDOC1
 SDOC1 : Select Flash Disk Address
Flash Disk Address SDOC1
C800H~C9FFH 1-2,7-8
CC00H~CDFFH 1-2,9-10
D000H~D1FFH 3-4,7-8
D400h~D5FFH 3-4,9-10
D800H~D9FFH 5-6,7-8
DC00H~DDFFH 5-6,9-10
2
4
6
8
10
1
3
5
7
9
SDOC1
Default :
SDOC
C800H~C9FFH
2
4
6
8
10
1
3
5
7
9
SDOC
D800H~D9FFH
SDOC
D400H~D5FFH
SDOC1
SDOC
D000H~D1FFH
SDOC
CC00H~CDFFH
SDOC
DC00H~DDFFH
9
User’s Manual

Chapter 2 Installation
2.2.3 I/O Connectors Summary
LOCATION FUNCTION
PLRS1 Power LED, HD LED, Reset, Speaker Connector (11 Pin 2.54mm)
PSW1 For ATX Power Button
PS7M1 7-Pin Power Connector
PS4W1 4-Pin Power Connector
ATXE1 For ATX Function
USABF1 USB Port #1&#2 Connector 2°5 Pin 2.54mm
USABF2 USB Port #1&#2 Connector 2°5 Pin 2.54mm
PKMB1 PS/2 Keyboard & Mouse Connector
LPTC1 Parallel Connector
IRDA1 IRDA1 Connector
COME1 COM1, COM2, COM3, COM4 Connector
FDCC1 Floppy Interface Connector (34 Pin Header)
CN2 Disk-On-Chip Socket
LANI1 Type 2 (RJ-45 with LED)
IDEA1 IDE Interface Connector
IDEB1 IDE Interface Connector
LVDSC1 LVDS Panel Connector 2x15P 1.0mm SMT
LCD1 Panel LCD Connector (50Pin 1.0mm JST Header)
VGAB1 VGA Connector
INVER1 LCD INVETER Connector
DIOB1 Digital Input / Digital Output Ports
FAN1 3 Pin FAN Connector
PCON1 pc/104 + Connector
PCONB1 PC/104 Connector
CF1 Compact Flash Connector
zPLRS1: Power LED, HD LED, Reset, Speaker Connector (11 Pin 2.54mm)
Pin No. Description
1 Power LED +
2 Power LED +
3 GND
4 HDD LED +
5 HDD LED -
6 RESET SW +
7 RESET SW – (GND)
8 External Speaker -
9 Internal Buzzer -
10 NC
11 External Speaker +
Default : 8-9 (ON) Internal Buzzer
PLRS1
1
PLRS1
11
10 User’s Manual

Chapter 2 Installation
7
654321
4321
PS4W1
PS7M1
PSW1
zPSW1: For ATX Power Button
Pin No. Description
1 PANSW
2 GND
1
2
PSW1
zPS7M1:7Pin Power Connector
Pin No. Description
1 +5V
2 GND
3 GND
4 +12V
5 NC
6 GND
7 +5V
PS7M1
zPS4W1：4P Power Connector（WAFER 4P 2.00mm）
Pin No. Description
1 GND
2 -5V
3 GND
4 -12V
PS4W1
11
User’s Manual

Chapter 2 Installation
zATXE1: For ATX Function ( WAFER 3P 2.0mm )
Pin No. Description
1 PSON
2 GND
3 +5V STANDBY
ATXE1
ATXE1
321
zUSBF1：USB Port #1 & #2 (Connector 2x5 Pin 2.00mm)
Pin No. Description Pin No. Description
1 USB_VCC 2 Ground
3 Key 4 USBD1+
5 USBD0- 6 USBD1-
7 USBD0+ 8 Key
9 Ground 10 USB_VCC
USBF1
USBF2
1
9
2
10
USBF1
zUSBF2：USB Port #3 & #4 (Connector 2x5 Pin 2.00mm)
Pin No. Description Pin No. Description
1 USB_VCC 2 Ground
3 Key 4 USBD1+
5 USBD0- 6 USBD1-
7 USBD0+ 8 Key
9 Ground 10 USB_VCC
1
9
2
10
USBF2
12 User’s Manual

Chapter 2 Installation
zPKMB1:PS/2 Keyboard & Mouse Connector (2x4 Header 2.54mm )
Pin No. Description Pin No. Description
1 VCC 2 MSCLK
3 MSDATA 4 NC
5 KBDATA 6 NC
7 GND 8 KBCLK
PKMB1
1
25
2
26
LPTC1
1
7
2
8
PKMB1
zLPTC1：Parallel Connector (26 Pin 2.00mm Pitch Header)
Pin No. Description Pin No. Description
1 Strobe # 2 Auto Form Feed
3 Data0 4 Error #
5 Data1 6 Initialize #
7 Data2 8 Printer Select IN #
9 Data3 10 Ground
1 Data4 12 Ground
13 Data5 14 Ground
15 Data6 16 Ground
17 Data7 18 Ground
19 Acknowledge # 20 Ground
21 Busy 22 Ground
23 Paper Empty 24 Ground
25 Printer Select 26 KEY
LPTC1
IRDA1
zIRDA1:IRDA1 Connector
Pin No. Description
1 VCC
2 NC
3 IRRX
4 GND
5 IRTX
IRDA1
1
5
13
User’s Manual

Chapter 2 Installation
zCOME1:COM1,COM2,COM3,COM4 Connector
Pin No. Description Pin No. Description
1 NDCD1 2 NDSR1
3 NSIN1 4 NRTS1
5 NSOUT1 6 NCTS1
7 NDTR1 8 CA-D9
9 GND 10 NC
11 COM2_1 12 NDSR2
13 COM2_2 14 NRTS2
15 COM2_3 16 NCTS2
17 COM2_4 18 CB-P9
19 GND 20 NC
21 NDCD3 22 NDSR3
23 NSIN3 24 NRTS3
25 NSOUT3 26 NCTS3
27 NDTR3 28 CC-P9
29 GND 30 NC
31 NDCD4 32 NDSR4
33 NSIN4 34 NRTS4
35 NSOUT4 36 NCTS4
37 NDTR4 38 CD-P9
39 GND 40 NC
FDCC1
1
2 34
33
zFDCC1: Floppy Interface Connector (34 Pin Header)
Pin No. Description Pin No. Description
1 Ground 2 Density Select
3 Ground 4 KEY
5 Ground 6 DS1
7 Ground 8 Index #
9 Ground 10 Motor Enable A #
11 Ground 12 Drive Select B #
13 Ground 14 Drive Select A #
15 Ground 16 Motor Enable B #
17 Ground 18 Direction #
19 Ground 20 Step #
21 Ground 22 Write Data #
23 Ground 24 Write Gate #
25 Ground 26 Track 0 #
27 Ground 28 Write Protect #
29 NC 30 Read Data #
31 Ground 32 Head Side Select #
33 NC 34 Disk Change #
2 40
FDCC1
COME1
39
1 COME1
14 User’s Manual

Chapter 2 Installation
zCN2: Disk-On-Chip Socket
Pin No. Description Pin No. Description
1 AEN 17 SD3
2 IOW# 18 SD4
3 GND 19 SD5
4 SA12 20 SD6
5 SA7 21 SD7
6 SA6 22 CE#
7 SA5 23 SA10
8 SA4 24 SMEMR#
9 SA3 25 SA11
10 SA2 26 SA9
11 SA1 27 SA8
12 SA0 28 SA13
13 SD0 29 SA14
14 SD1 30 +5V
15 SD2 31 SMEMW#
16 GND 32 +5V
LANI1
CN2
16
17
CN2
32
1
zLANI1:LAN CONNECTOR
Pin No. Description Pin No. Description
1 TX+ 2 TX-
3 LGND 4 NC
5 RX+ 6 RX-
7 T45 8 T78
9 LSPEED+ 10 LSPEED-
11 LNKACT+ 12 LNKACT-
1
11
2
12
LANI1
15
User’s Manual

Chapter 2 Installation
zIDEA1: IDE Interface Connector (44Pin 2.0mm Pitch Header)
Pin No. Description Pin No. Description
1 Reset # 2 Ground
3 Data 7 4 Data 8
5 Data 6 6 Data 9
7 Data 5 8 Data 10
9 Data 4 10 Data 11
11 Data 3 12 Data 12
13 Data 2 14 Data 13
15 Data 1 16 Data 14
17 Data 0 18 Data 15
19 Ground 20 Key
21 DMA REQ # 22 Ground
23 IOW # 24 Ground
25 IOR # 26 Ground
27 IOCHRDY 28 Ground
29 DMA ACK # 30 Ground
31 Interrupt 32 NC
33 SA 1 34 NC
35 SA 0 36 SA 2
37 HDC CS 0# 38 HDC CS 1#
39 HDD Active 40 Ground
41 VCC 42 VCC
43 Ground 44 NC
IDEA1
1
39
2
40
43
1
44
2
IDEB1
IDEA1
zIDEB1: IDE Interface Connector (40Pin 2.54mm Pitch Header)
Pin No. Description Pin No. Description
1 Reset # 2 Ground
3 Data 7 4 Data 8
5 Data 6 6 Data 9
7 Data 5 8
Data 10
9 Data 4 10 Data 11
11 Data 3 12 Data 12
13 Data 2 14 Data 13
15 Data 1 16 Data 14
17 Data 0 18 Data 15
19 Ground 20 Key
21 DMA REQ# 22 Ground
23 IOW # 24 Ground
25 IOR # 26 Ground
27 IOCHRDY 28 Ground
29 DMA ACK # 30 Ground
31 Interrupt 32 NC
33 SA1 34 PD80P
35 SA0 36 SA2
37 HDC CS0 # 38 HDC CS1 #
39 HDD Active
LED # 40 Ground
IDEB1
16 User’s Manual