Lanner electronics EM-660 Series User manual

EM-660 Series
VIA C3 Processor Embedded SBC
with SODIMM, VGA, LCD/LVDS,
CF II, Sound, LAN, PCI
and PC/104 expansion
USER'S MANUAL

COPYRIGHT©
This document is a copyright of the original manufacturer, 2002. The original manufacturer reserves
the rights to make improvement and/or modification to the product described in this manual at any
time without further notice. This manual may not, in whole or in part, be photocopied, reproduced,
transcribed, translated, or transmitted in whatever form without the written consent of the
manufacturer, except for copies retained by the purchaser for backup purposes. All rights are
reserved.
TRADEMARKS
The following are trademarks or registered trademarks of their respective companies: IBM, Intel, AMD,
Cyrix, NS, Award, AMI, Microsoft, Windows, Windows NT, Novell, SCO, PC/104, PICMG, ALI, UMC, VIA,
S3, Realtek, SMC and Winbond. Products mentioned in this manual are mentioned for identification
purposes only. All names of products or services appearing in this manual are the trademarks or
registered trademarks of their respective organizations and companies.
Copyright 2003
Version: 1.0
Date: 2003/02/27

TABLE OF CONTENTS
CHAPTER 1 INTRODUCTION .............................................................................................................. 1
1.1 INTRODUCTION ......................................................................................................................................1
1.2 FEATURES .............................................................................................................................................1
1.3 SPECIFICATION.......................................................................................................................................2
1.4 UNPACK YOUR EM-660 SERIES..................................................................................................................2
1.5 BOARD LAYOUT ......................................................................................................................................3
CHAPTER 2 INSTALLATION................................................................................................................ 4
2.1 SYSTEM MEMORY INSTALLATION .................................................................................................................4
2.2 JUMPER SETTINGS AND CONNECTORS...........................................................................................................5
2.2.1 Board Outline .............................................................................................................................5
2.2.2 Jumper Settings Summary.............................................................................................................6
2.2.3 I/O Connectors Summary ............................................................................................................11
CHAPTER 3 BIOS SETUP................................................................................................................... 32
3.1 RUNNING AWARD BIOS .......................................................................................................................32
Entering Setup ....................................................................................................................................32
3.2 CMOS SETUP UTILITY...........................................................................................................................33
3.3 STANDARD CMOS SETUP........................................................................................................................35
Primary Master / Primary Slave.............................................................................................................36
3.4 BIOS FEATURES SETUP..........................................................................................................................38
3.5 CHIPSET FEATURES SETUP.......................................................................................................................40
3.6 INTEGRATED PERIPHERALS ......................................................................................................................43
3.7 POWER MANAGEMENT SETUP ...................................................................................................................45
3.8 PNP/PCI CONFIGURATION ......................................................................................................................47
3.9 PC HEALTH STATUS (OPTIONAL) ..............................................................................................................49
3.10 LOAD OPTIMIZED DEFAULTS...................................................................................................................50
3.11 SET SUPERVISOR / USER PASSWORD........................................................................................................51
3.12 SAVE & EXIT SETUP.............................................................................................................................52
3.13 EXIT WITHOUT SAVING ........................................................................................................................53
CHAPTER 4 DRIVERS SUPPORT .......................................................................................................54
4.1 USE YOUR DRIVER CD-ROM...................................................................................................................54
4.2 FILE DIRECTORY...................................................................................................................................54
APPENDIXA. WATCH-DOG TIMER .................................................................................................... 55
APPENDIXB. BRIGHTNESS CONTROL............................................................................................... 55
RMA SERVICE REQUEST FORM......................................................................................................... 57

Chapter 1 Introduction
1
User’s Manual
Chapter 1 Introduction
1.1 Introduction
EM-660 offers two computing power options: VIA C3 533MHz and C3 800MHz. VIA C3 533MHz is
designed especially for fan-less requirement to enable better MTBF. As an x86 architecture, the platform
supports prevail operating systems such as Windows 95/98SE/XP/2000/NT and Linux. Your previous
investment on these operating systems is, thus, protected in the following 4 years. With 192KB internal
L1/L2 cache integrated in the CPU, your applications are able to benefit more execution speed from this
mechanism.
VIA Twister-T chipset is the mid-end position of VIA chipsets. It supports 2D/3D Video Accelerator by
integrating S3 Savage4. It also supports 36-bit TFT LCD and 2 channel (2 x 18-bit) LVDS. Using LCD
50-pin box header, EM-660 is able to compatible with the most coming bigger size industrial and
commercial LCDs. By enabling VRAM, the system can further cut its cost and while maintains its speed.
EM-660 uses SODIMM to limit its board height and supports PC 133/PC 100.
There are two storage options in EM-660 design. One is EIDE, and the other is CF II. EIDE supports two
IDE devices. EM-660 offers 2 IDE box header options to fulfill flexible hard disk placement in system
design. 40-pin box header focuses on 3.5” hard disk, 44-pin box header mainly couples itself with 2.5”
hard disk. Regarding to CF II socket, system can further cut its whole size when using popular large
volume CF II form factor SSD.
EM-660 embodies the following I/O: 1 x LAN, 1 x FDD, 4 x COM, 1 x LPT, Keyboard & Mouse, 2 x USB, 1
x IrDA and 4 x DIO. Expansion slots include PC/104 and PCI. Power supply complies with AT and ATX.
Watchdog timer is 16-level.
As an industrial PC embedded card, EM-660’s operating temperature is ranging from 0°C to 60°C. All
these numerous features provide an ideal price/performance solution for commercial and industrial
applications where stability and reliability are essential.
1.2 Features
!" VIA C3 533MHz Fanless and C3 800MHz/ FSB 133MHz
!" VIA VT8606 North Bridge and VT82C686B South Bridge
!" Award BIOS
!" S3 Savage 4 2D/3D Video Accelerator
!" VGA, 36-bit TTL LCD and 2!18-bit LVDS
!" LCD Brightness Control via GPIO
!" AC 97 Audio
!" Realtek RTL 8100B
!" CF Type II Socket
!" PCI and PC/104 expansion slots
!" 1 x LAN, 1 x FDD, 4 x COM, 1 x LPT, Keyboard & Mouse, 2 x USB, 1 x IrDA and 4 x DIO
!" Watchdog Timer
!" AT/ATX Connector, ATX is default

Chapter 1 Introduction
2 User’s Manual
1.3 Specification
EM-660 Series
!"Processor : On board VIA C3 EBGA Ultra Low Power Processor, up to 133MHz,
Intergrated 192 KB internal L1/L2
!"Chipset : VIA VT8606 North Bridge & VT82C686B South Bridge, FSB 133MHz
!"System Memory / RAM :
: One SODIMM socket supports up to 256MB SDRAM SDRAM PC 133/PC100
!"VGA/LCD : VIA Twister Chip with Integrated S3 Savage 4 2D/3D Video Accelerator,
Support up to 36-bit TTL LCD and 2 channel (2!18 bit) LVDS Reserved
Design Option: LCD Brightness Control via GPIO
Support 8/16/32 MB Display Memory (Shared)
One DB-15 VGA connector and one 2x8x2.54 mm box-header
!"Ethernet : One RJ-45 connector, Realtek RTL8100B, 10/100 Base-T interface
!"BIOS : 256KB Award license BIOS
!"RTC : Internal RTC with Li battery
!"Flash Memory Disk : Type I/II CFC Socket supports up to 512 MB flash memory disk or IBM Micro
Drive up to 1GB
!"IDE Drive Interface : PIO mode 4 and Bus Master. Also supports Multi-word DMA and Ultra DMA
33/66/100, one 2x20x2.54 mm PCI IDE port and one 2!22!2.00mm,
support up to four IDE devices.
!"Floppy Interface : One 1x26x1.0 mm FDD port (support one floppy device)
!"Serial Port :Four COM ports with ESD protect, COM1 RS-232/422/485 DB-9 connector,
COM2 RS-232 DB-9 connector, COM3 RS-232 DB-9 connector, and COM4
RS-232 2x5x2.54mm Box-header
!"Parallel Port : One multi-mode parallel port (SPP/EPP/ECP) DB-25 connector
!"Keyboard/Mouse : One 6-pin mini-DIM PS/2 keyboard/mouse connector and one 6-pin 1x6x2.54
mm internal keyboard/mouse header (KBDAT, MSDAT, KMGND, KC-FUS,
KBCLK, MSCLK)
!"Universal Serial Bus : Support USB 1.1; 2 x external Connector, (Reserved design 2 x internal
pin-header)
!"IR Interface : Supports one IrDA header
!"Expansion Bus : Built-in one PCI & PC/104 expansion slot
!"Digital I/O : Digital-in*4 and digital-out*4
!"Watchdog Timer : Software 16 level time-out intervals
!"Health Monitoring : Integrated in 686B
!"Power Connector : On-board power connector, with one ATX/AT co-design power connector
optional and one HDD 4T connector
!"Operating Temperature : 0°C ~ 60°C
!"Storage Temperature : -20°C ~ 70°C
!"Humidity : 5% ~ 95% RH, non-condensing
!"Dimensions : 219x159 mm +/- 0.5mm
!"Net Weight : 350 g (0.77 pounds)
!"EMI/EMS : Meet CE and FCC class A regulation
1.4 Unpack your EM-660 Series
Before you begin to install your card, please make sure that you received the following materials as listed
below:
Standard Packing:
!"EM-660 x 1 pc Embedded Single Board Computer
!"Driver Utility CD-ROM x 1 pc Drivers & Utilities
!"User's Manual x 1 pc This User's Manual
!"Comport Cable x 1 pc D-SUB 9P To 2!5P with Key 230mm EDI
!"Floppy Cable x 1 pc 26P Flat 200mm (up contact)
!"Floppy Cable x 1 pc 26P Flat 200mm (down contact)
!"ATA Cable x 1 pc ATA100 40P IDE Impendence with Key
!"IDE Cable x 1 pc 40P!2 to 44P P20 with Key EDI
!"Nut & Spacer x 4 sets 15mm hex-spacer

Chapter 1 Introduction
3
User’s Manual
1.5 Board Layout

Chapter 2. Installation
4 User’s Manual
Chapter 2 Installation
2.1 System Memory Installation
Step 1: Insert the RAM module into the SODIMM socket
Step 2: Press Module down till clip hold.

Chapter 2 Installation
5
User’s Manual
2.2 Jumper Settings and Connectors
2.2.1 Board Outline
LNO1 SPEAK1MIC1 LNI1
SC2T2
SC2T1
ATXC1
CMOS1
FAN1
1 3
SCF1
SBVA1
CONB1
CONA1
1
4
2
1
1
1
1
2
1
1
1
1
1
3
1
1
1
1
2
1
6
5
SRIVB3
SRIVB4
PLRS1
1
IDEB1
IDEA1
PSW1
1
LCD1
PS4W1
LPTB1
LVDSC1
FDCB1
INVER1
PSA1
PS4M1
IKBM1
CDIN1
1COMB1
VLCD1
SLCDA1
1
USBLN1
V
GAC1
1 ISPKR1
IRDA1
USBA1
DIOA1
2
1
1
2
1
SRIVB1
1
SRIVB2
1
CPU1
COMF1
1
1
KM1
6
5
2
49 50
1 2
29 30
26 1
A B
D C
1
1 JFA1
V
GACM1
10
9
10
9
9
12
1
12

Chapter 2. Installation
6 User’s Manual
SC2T2
2.2.2 Jumper Settings Summary
LOCATION FUNCTION
CMOS1 Clear CMOS Data
SC2T1/SC2T2 Select COM1 Type
SRIVB1/SRIVB2 Select COM1, COM2 port pin 9 Type
VLCD1 Select Panel Voltage
SBVA1 Select AT/ATX Power
SCF1 Master/Slave Select
SRIVB3/SRIVB4 Select COM3, COM4 Pin9 Type
SLCDA1 Select Panel Type
!" CMOS1 : Clear CMOS Data
Description CMOS1
Normal (Default) 1-2
Clear CMOS 2-3
!"SC2T1/SC2T2: Select COM1 Type
COM1 TYPE SC2T1 SC2T2
RS-232 (Default) 1-2 1-5,2-6,3-7,4-8
RS-422 3-4 5-9,6-10,7-11,8-12
RS-485 5-6 5-9,6-10,7-11,8-12
CMOS1
1
2
3
SC2T1
5 6
1 2
4 12
91
RS-232
RS-422
RS-485
CMOS1
SC2T1
SC2T2

Chapter 2 Installation
7
User’s Manual
!"SRIVB1, SRIVB2: Select COM1, COM2 port pin 9 Type
!" VLCD1: Select Panel Voltage
Panel Voltage VLCD1
+3.3V (Default) 1-2
+5V 2-3
SRIVB1
Pin 9 Type COM1 COM2 SRIVB2
RI (Default) 1-3 2-4 1-2
+5V 3-5 4-6 1-2
+12V 3-5 4-6 2-3
SRIVB1
1 3 5
SRIVB2
VLCD1
3.3V (Default) VLCD1
5V
Default: VLCD1
1
2
3
1 2 3
1
2
3
1
2
3
1
2
3
2 4 6
SRIVB1
SRIVB2
V
LCD1

Chapter 2. Installation
8 User’s Manual
!"SBVA1: Select power supply Type
Power Type SBVA1
AT 1-3,2-4
ATX（Default）3-5,4-6
!"SCF1: Master/Slave Select
Compact Flash Card ATA Disk Chip SCF1
Master Slave 1-2
Slave Master 2-3 (Default)
AT
ATX
(Default)
Default:
SBVA1
1
3
SCF1
2 4 6
1 3 5
2 4 6
1 3 5
2 4 6
1 3 5
2 4 6
1 3 5
SCF1
SBVA1

Chapter 2 Installation
9
User’s Manual
!"SRIVB3,4:Select COM3,COM4 Pin9 Type
SRIVB3
PIN 9 Type com3 com4 SRIVB4
RI（Default）1-3 2-4 1-2
+5V 3-5 4-6 1-2
+12V 3-5 4-6 2-3
SRIVB4
SRIVB3
1 2 3
2 4 6
1 3 5
SRIVB3
SRIVB4

Chapter 2. Installation
10 User’s Manual
!"SLCDA1:Select Panel Type (2x4 Pin)
Note: Different type of LCD panel with the same resolution will have different jumper setting for
selection. Panel Type SLCD1
640 x 480 TFT 1-2,3-4,5-6,7-8
800 x 600 TFT 3-4,5-6,7-8
1024 x 768 TFT 2pixel/Clk at 32MHZ 1-2,5-6,7-8
1280 x 1024 TFT 5-6,7-8
640 x 480 DSTN 1-2,3-4,7-8
800 x 600 DSTN 3-4,7-8
1024 x 768 DSTN 1-2,7-8
1024 x 768 TFT 1pixel/Clk at 65MHZ 7-8
640 x 480 TFT 1-2,3-4,5-6
800 x 600 TFT 3-4,5-6
1024 x 768 TFT 1-2,5-6
1280 x 1024 TFT 5-6
1400 x 1050 TFT 2pixel/Clk at 54MHZ 1-2,3-4
800 x 600 DSTN 3-4
1024 x 768 DSTN 1-2
1280 x 1024 DSTN OFF
Default
All OFF:
SLCDA1
1 3 5 7
2 4 6 8
SLCD1A1
640X480 TFT
800 x 600 TFT
1024 x 768 TFT 2pixel/Clk at 32MHZ
1280 x 1024 TFT
640 x 480 DSTN
800 x 600 DSTN
1024 x 768 DSTN
1024x768 TFT/ pixel/ Clk at 65MHZ
640 x 480 TFT
800 x 600 TFT
1024 x 768 TFT1280 x 1024 TFT
1400 x 1050 TFT 2pixel/Clk at 54MHZ800 x 600 DSTN
1024x1024 DSTN1280x1024 DSTN
1 3 5 7
2 4 6 8
SLCDA1

Chapter 2 Installation
11
User’s Manual
2.2.3 I/O Connectors Summary
LOCATION FUNCTION
PLRS1 Power LED, HD, LED, Reset, Speaker Connector
IRDA1 IRDA Connector
USBA1 USB Port #3 &#4 Connector 2!5 Pin 2.54mm
LPTB1 Parallel Port Connector
LVDSC1 LVDS Panel Connector 2!15P 1.0mm SMT
FDCB1 Slim Floppy Interface Connector
INVER1 LCD INVERTER Connector
LCD1 Panel LCD Connector
IDEA1 IDE Interface Connector (44 Pin 2.0mm Pitch Header)
IDEB1 IDE Interface Connector (40 Pin 2.54mm Pitch Header)
PS4W1 4-Pin Power Connector (WAFER 4P 2.00mm)
PSA1 20 Pin ATX Power Connector
DIOA1 Digital Input/ Digital Output Ports (2!5 Pin 2.54mm Header)
ATXC1 For ATX Function
PSW1 For ATX Power Button
CONA1 /CONB1 PC/104 Connector (8 bit/16 bit)
FAN1 3Pin FAN Connector
COMF1 Serial port #1 & #2 Connector, Double stack 9 Pin D-USB MALE
USBLN1 LAN & USB port #1 & #2 Connector Double stack 8 Pin RJ45+8 Pin USB
VGACM1 VGA & Serial port #3, Double stack 15 Pin D-SUB Female & 9 Pin D-SUB Male
PS4M1 4Pin Power Connector (Big-4P Male)
CF1 Compact Flash Connector
IKBM1 Internal Keyboard, Mouse Connector (6Pin 2.54mm Header)
KM1 Keyboard & Mouse Connector, Double stack 6 Pin mini DIN Female
VGAC1 Internal VGA Connector (2!8 Pin 2.54mm Pitch Header)
MIC1 MIC IN 5Pin-PHONE Jack
LNI1 Line IN 5Pin-PHONE Jack
CDIN1 CD_IN Connector
ISPKR1 Internal Speaker Connector
LNO1 Line out 5Pin-PHONE Jack
SPEAK1 Header phone connector 5Pin-PHONE Jack
COMB1 Serial Port #4 Connector (Header)

Chapter 2. Installation
12 User’s Manual
!"PLRS1: Power LED, HD LED, Reset, Speaker Connector (11 Pin 2.54mm)
Pin No. Description
1 Power LED +
2 Power LED +
3 GND
4 HDD LED +
5 HDD LED -
6 RESET SW +
7 RESET SW – (GND)
8 External Speaker -
9 Internal Buzzer -
10 NC
11 External Speaker +
!"IRDA1: IRDA Connector
Pin No. Description
1 +3.3V
2 NC
3 IRRX
4 GND
5 IRTX
IRDA1
5
1
Default :
8-9 (ON) Internal Buzzer 11
1
PLRS1
PLRS1
IRDA1

Chapter 2 Installation
13
User’s Manual
"
""
"USBA1: USB Port #3 & #4 Connector 2x5 Pin 2.54mm
Pin No. Description Pin No. Description
1 +5VSB 2 +5VSB
3 USBD2- 4 USBD3-
5 USBD2+ 6 USBD3+
7 Ground 8 Ground
9 USB Port #3Ground 10 USB Port #4Ground
"
""
"LPTB1: Parallel Port Connector (25 Pin D-Sub)
Pin No. Description Pin No. Description
1 Strobe # 14 Auto Form Feed #
2 Data0 15 Error #
3 Data1 16 Initialize #
4 Data2 17 Printer Select IN #
5 Data3 18 Ground
6 Data4 19 Ground
7 Data5 20 Ground
8 Data6 21 Ground
9 Data7 22 Ground
10 Acknowledge # 23 Ground
11 Busy 24 Ground
12 Paper Empty 25 Ground
13 Printer Select
9 1
2
10
USBA1
1 13
14 25
LPTB1
USBA1
LPTB1

Chapter 2. Installation
14 User’s Manual
"
""
"LVDSC1
：
： ：
：
LVDS Panel Connector 2x15P 1.0mm SMT
Pin No. Description Pin No. Description
1 FVCC 2 FVCC
3 GND 4 GND
5 NC 6 +12V
7 Y0M 8 Z0M
9 Y0P 10 Z0P
11 GND 12 GND
13 Y1M 14 Z1M
15 Y1P 16 Z1P
17 GND 18 GND
19 Y2M 20 Z2M
21 Y2P 22 Z2P
23 GND 24 GND
25 YCM 26 ZCM
27 YCP 28 ZCP
29 GND 30 GND
"
""
"FDCB1: Slim Floppy Interface Connector (26 Pin Header)
Pin No. Description Pin No. Description
1 VCC 14 STEP-
2 INDEX- 15 GND
3 VCC 16 WD-
4 DSA- 17 GND
5 VCC 18 WE-
6 DSKCHG- 19 GND
7 NC 20 TRAK0-
8 NC 21 GND
9 NC 22 WP-
10 MOA- 23 GND
11 NC 24 RDATA-
12 DIR- 25 GND
13 NC 26 HEAD-
LVDSC1
1 2
29 30
1
26
FDCB1
LVDSC1
FDCB1

Chapter 2 Installation
15
User’s Manual
"
""
"INVER1: LCD INVERTER Connector
Pin No. Description
1 GND
2 +5V
3 +12V
4 ENAVEE
5 Bright
#Regular pin 5 (bright) output is 1.8V. But output can be adjusted by below software tools.
EM60SAWD.EXE for output: 0 ~ 1.8V
EM60LAWD.EXE for output: 0 ~ 3.3V
Brightness Adjust Operation:
Power-on by DOS booting disk, execute software tool and push "+" bottom to increase voltage or push "-"
bottom to decrease voltage.
"
""
"LCD1: Panel LCD Connector (50Pin 1.0mm JST Header)
Pin No. Signal Pin No. Signal
1 FVCC 2 FVCC
3 LP 4 FLM
5 M/DE 6 NC
7 ENAVEE 8 ENAVDD
9 SHFCLK 10 +12V
11 GND 12 GND
13 P0 14 P1
15 P2 16 P3
17 P4 18 P5
19 P6 20 P7
21 P8 22 P9
23 P10 24 P11
25 P12 26 P13
27 P14 28 P15
29 GND 30 P16
31 P17 32 P18
33 P19 34 P20
35 P21 36 P22
37 P23 38 GND
39 P24 40 P25
41 P26 42 P27
43 P28 44 P29
45 P30 46 P31
47 P32 48 P33
49 P34 50 P35
INVER1
1
2
3
4
5
LCD1
2 50
1 49
INVER1
LCD1

Chapter 2. Installation
16 User’s Manual
!"Flat Panel Interface Pins listing for DSTN and color TFT LCD
SR7D[3] 0 0 0 0 0 0
SR70[0] 1 1 1 0 0 0
SR79[1-0] 10 10 10 10 10 10
SR7D[2-0] 001 000 010 010 000 010
Pin Name STN8 STN16 ATN24 DSTN8 DSTN16 DSTN24
FPD0 R0 R0 R0 LR0 LR0 LR0
FPD1 G0 G0 G0 LR3
FPD2 B0 B0 B0 LG0 LG0 LG0
FPD3 R1 R1 R1
FPD4 G1 G1 G1 LB0 LB0 LB0
FPD5 B1 B1 B1
FPD6 R2 R2 R2 LR1 LR1 LR1
FPD7 G2 G2 G2 LG3
FPD8 B2 B2 LG1 LG1
FPD9 R3 R3
FPD10 G3 G3 LB1 LB1
FPD11 B3 B3
FPD12 R4 R4 LR2 LR2
FPD13 G4 G4 LB3
FPD14 B4 B4 LG2 LG2
FPD15 R5 R5
FPD16 G5 LB2
FPD17 B5
FPD18 R6 UR0 UR0 UR0
FPD19 G6 UR3
FPD20 B6 UG0 UG0 UG0
FPD21 R7
FPD22 G7 UB0 UB0 UB0
FPD23 B7
FPD24 UR1 UR1 UR1
FPD25 UG3
FPD26 UG1 UG1
FPD27
FPD28 UB1 UB1
FPD29 UB3
FPD30 UR2 UR2
FPD31 UB3
FPD32 UG2 UG2
FPD33
FPD34 UB2
FPD35