Lanner electronics IAC-H668 Series User manual

IAC-H668 SERIES
HALF-SIZE SBC
WITH VGA AND LAN FOR
SOCKET 370 PENTIUM III PROCESSOR
User's Manual

COPYRIGHT ©
This document is a copyright of the original manufacturer, 2000. The original
manufacturer reserves the right to make improvements to the product(s) described
in this manual at any time without notice. This manual may not, in whole or in
part, be photocopied, reproduced, transcribed, translated, or transmitted in any
form without the written consent of the manufacturer, except for copies retained by
the purchaser for backup purposes. All rights reserved.
TRADEMARKS™
Pentium®, Celeron™ are registered trademark of Intel Corporation.
The following are trademarks or registered trademarks of their respective
companies: IBM, Intel, AMD, Cyrix, Award, AMI, Microsoft, Windows, Windows NT,
Novell, SCO, PC/104, PICMG, ALI, UMC, SMC, Winbond. Products mentioned in this
manual are mentioned for identification purposes only. All names of products or
services appearing in this manual are the trademarks or registered trademarks of
their respective organizations and companies.
ãCopyright 2001
Date: 2001/10/9

TABLE OF CONTENTS
CHAPTER 1General Information………………………………………… 1
1.1 Introduction……………………………………….….………………… 1
1.2 Features……………………………………………..….……………….. 1
1.3 Specification……………………………………….……….…………… 2
1.4 Unpack Your IAC-H668 and accessory…….…………………… 2
1.5 Board Layout Of IAC-H668………………………….….………….. 3
CHAPTER 2Installation……..……………………………………………… 4
2.1 Hardware Setup and Installation…………………………………. 4
2.1.1CPU Installation……………….…………………………….….. 4
2.1.2System memory Installation…………….…………….……. 6
2.1.3DISKONCHIP Installation..……………………….…………….. 6
2.2 Jumper Setting and Connectors……………………….………..… 7
2.2.1Board Outline……………………………………..………………. 7
2.2.2Jumper Setting Summary……………….…………………..... 8
2.2.3I/O Connector Summary……………………………….………. 10
CHAPTER 3BIOS Setup………………………………..……………………. 21
3.1 Running Award BIOS……………………………….…………………… 21
3.2 COMS Setup Utility………………………………………………………. 21
3.3 Standard CMOS Features..……………………………………………. 23
3.4 Advanced BIOS Features……………………………………………… 25
3.5 Advanced Chipset Features ………………………………………… 27
3.6 Integrated Peripherals………………………………………………… 29
3.7 Power Management Setup………………………………………….. 31
3.8 PnP/PCI Configurations………………………………………….…… 33
3.9 PC Health Status…………………………………………..…………… 34
3.10 Frequency/Voltage Control………………………………………….. 35
3.11 Load Fail-Safe Defaults………………………………………………… 35
3.12 Load Optimized defaults………………………………………………. 36
3.13 Supervisor/User Password……………………………………………. 36
3.14 Save & Exit Setup……………………………………………………….. 36
3.15 Exit Without Saving…………………………………………………….. 36
CHAPTER 4Drivers Support……………….……………………………… 37
4.1 Drivers Support..………………..……….……………………….……. 37
4.1.1Corechip.……………………………………………………………. 37
4.1.2Network Setup…………………………..……………………….. 37
4.1.3VGA Setup………………………………………………………….. 37
4.2 Driver Support List …………………………………………………….. 38
4.3 Driver Setup and Installation ………………………………………. 39
4.3.1Intel 815 Chipset Driver Setup.….………………………….39
4.3.2Intel Ultra ATA Storage Driver Install…………………….. 40
4.3.3VGA Driver Install…………..……….……..…………………… 42
4.3.4Network Driver Install…….………..………………………….. 45
APPENDIX A HOW TO USE WATCH-DOG TIMER
TERMS AND CONDITIONS
RMA SERVICE REQUEST FORM

Page:1
CHAPTER 1. General Information
1.1 Introduction
The IAC-H668 Series is a half-size Pentium®III/Celeron Single Board Computer (SBC) CPU card.
With integrated Intel 82562EN 10/100Base-TXEthernet chip, the IAC-H668 is targeting on the rapid
growing networking, and telecommunication markets. The supporting Intel DVMT (Dynamic Video
Memory Technology) makes IAC-H668 suitable for advanced 2D/3D graphic applications.
Its 8-layer printed circuit board combining with noise-tolerant and low power consumption CMOS
technology enables the IAC-H668 Series to withstand any harsh industrial environments very well.
The IAC-H668 Series SBC comes with enhanced hardware monitoring that monitors system and CPU
temperature, system voltages, and CPU/chassis fan speeds to prevent unexpected system failures by
warning the user of adverse conditions. The power management feature provides power savings by
slowing down the CPU clock, turning off the monitor screen or stopping the HDD spindle motor to
conserve energy.
Other standard features include two serial ports (one RS-232 and one RS-232/422/485 selectable),
one multi-mode (ECP/EPP/SPP) parallel port, one floppy drive controller, and one PS/2 keyboard /
mouse interface. The built-in PCI Enhanced IDE controller supports two IDE devices in Ultra ATA
100/66/33 bus master modes.
Carefully designed to be a feature-rich CPU card at a reasonable price, this board elegantly meets
industry needs and saves time and money by waiving the hassle of going through the extra effort and
cost of additional I/O cards. Being standards-compliant, it is proved to be a quality product with high
performance and stability in a long run.
1.2 Features
nVarious FSB (Front Side Bus) Support: 66/100/133MHz
nIntegrated VGA/LAN Functions (Intel 815E Chipset)
nDVMT (Dynamic Video Memory Technology) Enables Optimum Graphic And Memory
Performance For 2D/3D Graphics
nDisplay Resolution Up to 1600*1200*256 Colors @ 85Hz
nRemote Control Ability by Wake on LAN/Wake on MODEM Function
nPC/104 Expansion Possible
nHigh Reliability by Enhanced Hardware Monitoring Function
nMultiple Serial Port Type (RS-232/422/485) For Flexible Serial Communication
n4 USB Ports Supporting Extra Peripheral Connections

Page:2
1.3 Specification
IAC-H668 Series
Processor IntelÒPentium III/CeleronÔProcessor in Socket 370
(66/100/133 MHz)
Chipset IntelÒ815E chipset, IT8712F I/O Chipset,
IT8888 PCI to ISA Bridge
System Memory / RAM One 168-pin DIMM socket, support 100/133 MHz SDRAM
BIOS AwardÒlicensed BIOS
Flash Memory Disk Reserved socket for DiskOnChip from M-System,
support up to 288 MB flash memory disk
Graphics Controller Internal graphic controller with Intel’s Dynamic Video Memory Technology,
resolution up to 1600 x 1200 x 256 colors @ 85 Hz, with VGA connector
Ethernet Controller Intel 82562ET chip, support 10/100 Base-Tx Ethernet,
Wake On LAN supported via ATX power supply
IDE Drive Interface One PCI IDE port that support up to two IDE devices
and Ultra ATA/100/66/33
Floppy Drive Interface One FDD port, support up to two floppy devices
Serial Port Two COM ports, one RS-232 and one RS-232/422/485
Parallel Port One multi-mode parallel port (SPP / EPP / ECP)
Bus Interface ISA bus and PC/104 expansion bus
RTC Internal RTC with Li battery
Keyboard/Mouse 6-pin mini-Din PS/2 keyboard/mouse connector
and 5-pin keyboard header
Watchdog Timer 16-level time-out intervals
Digital I/O 4-bit digital I/O header
Universal Serial Bus Support 4 USB ports
IR Interface Support IrDA header
Health Monitoring Enhanced hardware monitor functions
Power interface 4-pin Aux-power connector and 4-pin ATX feature connector
Operating Temperature 0 °C~60 °C
Storage Temperature -20 °C~70 °C
Humidity 5 %~95%RH, non-condensing
Dimensions 185 x 122 mm ±0.5 mm
EMI/EMS
EN 50081-1/1994>EN 55022/1997>
EN 61000-3-2/1995>EN 61000-3-3/1995,
EN 50082-1/1994>IEC 1000-4-2/1995,
IEC 1000-4-3/1995, IEC 1000-4-4/1995
Ordering Information IAC-H668A:VGA/LAN
1.4 Unpack your IAC-H668 and Accessory
Before you begin to install your card, please make sure that you received the following materials as
listed below:
nIAC-H668 Series SBC x 1 pc Single Board Computer
nKeyboard and Mouse Cable x 1 pc 6pin Mini-Din PS/2 connector to 6pin PS/2 K/B
+6pin PS/2 Mouse Cable
nLPT/COM cable x 1 pc 26-pin to 25-pin with 10-pin to 9-pin D-Sub Cable
nATX Feature Cable x 1 pc 4-pin 40cm cable
nIDE Cable x 1 pc DMA-66 80pin IDE Cable
nFDD Cable x 1 pc 34 to 34-pin Standard Header Flat Ribbon Cable
nDriver Utility CD-ROM x 1 pc Drivers & Utilities
nUser's Manual x 1 pc This User's Manual

Page:3
1.5 Board Layout

Page:4
CHAPTER 2. Installation
2.1 Hardware Setup and Installation
2.1.1 CPU Installation and Upgrading
PGA370
Step1Locate the ZIF socket and open it by first pulling the lever of socket upward.
Step2Insert the CPU into the socket. Please keep the lever right angle when inserting CPU.

Page:5
Step3When inserting the CPU please note the correct orientation as shown.
The notched corner should point toward the end of the lever.
Step4Push the lever down to close the socket.
Step5Attach the heatsink onto the CPU.
Step6Push the clip of heatsink downward to hock the ear of socket firmly.
Step7Finally attach the fan cable to the CPU fan header.

Page:6
2.1.2 System Memory Installation
Step1Open latches of DIMM socket.
Step2Insert the RAM module into the DIMM socket.
Step3Press the latches into the notches of the RAM module.
2.1.3 DiskOnChip Installation
Please make sure the central polarization key on the socket, and place the DiskOnChip as the
same direction.