Lanner electronics IAC-H670 Series User manual

IAC-H670 Series
Half-size SBC
with VGA and LAN for
Socket 370 Pentium III Processor
User's Manual

COPYRIGHT©
This document is a copyright of the original manufacturer, 2001. The original manufacturer reserves the
right to make improvements to the product(s) described in this manual at any time without notice. This
manual may not, in whole or in part, be photocopied, reproduced, transcribed, translated, or transmitted in
any form without the written consent of the manufacturer, except for copies retained by the purchaser for
backup purposes. All rights reserved.
TRADEMARKS™
Pentium®, Celeron™ are registered trademark of Intel Corporation.
The following are trademarks or registered trademarks of their respective companies: IBM, Intel, AMD,
Cyrix, Award, AMI, Microsoft, Windows, Windows NT, Novell, SCO, PC/104, PICMG, ALI, UMC, SMC,
Winbond. Products mentioned in this manual are mentioned for identification purposes only. All names of
products or services appearing in this manual are the trademarks or registered trademarks of their
respective organizations and companies.
Copyright 2001
Ver. No. V1.1
Date: 2002/11/21

TABLE OF CONTENTS
Chapter 1 . Introduction ...................................................................................1
1.1 Introduction...........................................................................................................................1
1.2 Features ................................................................................................................................1
1.3 Specification ..........................................................................................................................2
1.4 Unpack your IAC-H670 and Accessory .....................................................................................2
1.5 Board Layout .........................................................................................................................3
Chapter 2 . Installation .....................................................................................4
2.1 Hardware Setup and Installation .............................................................................................4
2.1.1 CPU Installation and Upgrading .....................................................................................4
2.1.2 System Memory Installation...........................................................................................6
2.1.3 DiskOnChip Installation .................................................................................................6
2.2 Jumper Settings and Connectors .............................................................................................7
2.2.1 Board Outline of IAC-H670 ............................................................................................7
2.2.2 Jumper Setting Summary of IAC-H670 ...........................................................................8
2.2.3 I/O Connector Summary.............................................................................................. 10
Chapter 3 . BIOS Setup ...................................................................................22
3.1 Running AMI BIOS ............................................................................................................... 22
3.2 AMI BIOS HIFLEX Setup Utility ..............................................................................................23
3.3 Standard CMOS Setup .......................................................................................................... 25
3.4 Advanced CMOS Setup .........................................................................................................26
3.5 Advanced Chipset Setup ....................................................................................................... 29
3.6 Power Management Setup .................................................................................................... 32
3.7 PCI Plug and Play Setup ....................................................................................................... 34
3.8 Peripheral Setup................................................................................................................... 36
3.9 Hardware Monitor Setup ....................................................................................................... 38
3.10 Save & Exit Setup............................................................................................................... 38
3.11 Utility................................................................................................................................. 39
3.12 BIOS Defaults..................................................................................................................... 39
Chapter 4 . Drivers Support ............................................................................40
4.1 Use Your Driver CD-ROM ......................................................................................................40
4.2 File Directory ....................................................................................................................... 40
APPENDIXA. Watch-Dog Timer .......................................................................41
Terms and Conditions......................................................................................42

Chapter1 Introduction
1
User’s Manual
Chapter 1 . Introduction
1.1 Introduction
The IAC-H670 Series is a half-size Pentium®III/Celeron Single Board Computer (SBC) CPU card. With
integrated Intel 82562EN 10/100Base-TX Ethernet chip, the IAC-H670 is targeting on the rapid growing
networking, and telecommunication markets. The supporting Intel DVMT (Dynamic Video Memory
Technology) makes IAC-H670 suitable for advanced 2D/3D graphic applications.
Its 8-layer printed circuit board combining with noise-tolerant and low power consumption CMOS
technology enables the IAC-H670 Series to withstand any harsh industrial environments very well.
The IAC-H670 Series SBC comes with enhanced hardware monitoring that monitors system and CPU
temperature, system voltages, and CPU/chassis fan speeds to prevent unexpected system failures by
warning the user of adverse conditions. The power management feature provides power savings by
slowing down the CPU clock, turning off the monitor screen or stopping the HDD spindle motor to conserve
energy.
Other standard features include two serial ports (one RS-232 and one RS-232/422/485 selectable), one
multi-mode (ECP/EPP/SPP) parallel port, one floppy drive controller, and one PS/2 keyboard / mouse
interface. The built-in PCI Enhanced IDE controller supports two IDE devices in Ultra ATA 100/66/33 bus
master modes.
Carefully designed to be a feature-rich CPU card at a reasonable price, this board elegantly meets industry
needs and saves time and money by waiving the hassle of going through the extra effort and cost of
additional I/O cards. Being standards-compliant, it is proved to be a quality product with high performance
and stability in a long run.
1.2 Features
zVarious FSB (Front Side Bus) Support: 66/100/133MHz
zIntegrated VGA/LAN Functions (Intel 815E Chipset)
zDVMT (Dynamic Video Memory Technology) Enables Optimum Graphic And Memory Performance For
2D/3D Graphics
zDisplay Resolution Up to 1600*1200*256 Colors @ 85Hz
zRemote Control Ability by Wake on LAN/Wake on MODEM Function
zPC/104 Expansion Possible
zHigh Reliability by Enhanced Hardware Monitoring Function
zMultiple Serial Port Type (RS-232/422/485) For Flexible Serial Communication
z4 USB Ports Supporting Extra Peripheral Connections

Chapter1 Introduction
2 User’s Manual
1.3 Specification
IAC-H670 Series
Processor IntelTualatin (1.13/1.2/1.26GHz) & Coppermine Pentium III/Celeron
Processor in Socket 370
Chipset Intel815E chipset, IT8712F I/O Chipset, IT8888 PCI to ISA Bridge
System Memory / RAM One 168-pin DIMM socket, support 100/133 MHz SDRAM
BIOS AMI licensed BIOS
Flash Memory Disk Reserved socket for DiskOnChip from M-System, support up to 288 MB flash
memory disk
Graphics Controller Internal graphic controller with Intel’s Dynamic Video Memory Technology,
resolution up to 1600 x 1200 x 256 colors @ 85 Hz, with VGA connector
Ethernet Controller Intel 82562ET chip, support 10/100 Base-Tx Ethernet,
Wake On LAN supported via ATX power supply
IDE Drive Interface One PCI IDE port that support up to two IDE devices and Ultra
ATA/100/66/33
Floppy Drive Interface One FDD port, support up to two floppy devices
Serial Port Two COM ports, one RS-232 and one RS-232/422/485
Parallel Port One multi-mode parallel port (SPP / EPP / ECP)
Bus Interface ISA bus and PC/104 expansion bus
RTC Internal RTC with Li battery
Keyboard/Mouse 6-pin mini-Din PS/2 keyboard/mouse connector and 5-pin keyboard header
Watchdog Timer 16-level time-out intervals
Digital I/O 4-bit digital I/O header
Universal Serial Bus Support 4 USB ports
IR Interface Support IrDA header
Health Monitoring Enhanced hardware monitor functions
Power interface 4-pin ATX feature connector
Operating Temperature 0 °C~60 °C
Storage Temperature -20 °C~70 °C
Humidity 5 %~95%RH, non-condensing
Dimensions 185 x 122 mm ±0.5 mm
Ordering Information IAC-H670A: VGA/LAN
Optional USB Y Cable with bracket (0800100100002)
Note: CPU didn’t support PPGA processor .
1.4 Unpack your IAC-H670 and Accessory
Before you begin to install your card, please make sure that you received the following materials as listed
below:
zIAC-H670 Series SBC x 1 pc Single Board Computer
zKeyboard and Mouse Cable x 1 pc 6pin Mini-Din PS/2 connector to 6pin PS/2 K/B+6pin PS/2
Mouse Cable
zLPT/COM cable x 1 pc 26-pin to 25-pin with 10-pin to 9-pin D-Sub Cable
zATX Feature Cable x 1 pc 4-pin 40cm cable
zIDE Cable x 1 pc DMA-66 80pin IDE Cable
zFDD Cable x 1 pc 34 to 34-pin Standard Header Flat Ribbon Cable
zDriver Utility CD-ROM x 1 pc Drivers & Utilities
zUser's Manual x 1 pc This User's Manual

Chapter1 Introduction
3
User’s Manual
1.5 Board Layout

Chapter2 Installation
4 User’s Manual
Chapter 2 . Installation
2.1 Hardware Setup and Installation
2.1.1 CPU Installation and Upgrading
PGA370
Step 1 Locate the ZIF socket and open it by first pulling the lever of socket upward.
Step 2 Insert the CPU into the socket. Please keep the lever right angle when inserting CPU.

Chapter2 Installation
5
User’s Manual
Step 3 When inserting the CPU please note the correct orientation as shown. The notched corner
should point toward the end of the lever.
Step 4 Push the lever down to close the socket.
Step 5 Attach the heatsink onto the CPU.
Step 6 Push the clip of heatsink downward to hock the ear of socket firmly.
Step 7 Finally attach the fan cable to the CPU fan header.

Chapter2 Installation
6 User’s Manual
2.1.2 System Memory Installation
Step 1 Open latches of DIMM socket.
Step 2 Insert the RAM module into the DIMM socket.
Step 3 Press the latches into the notches of the RAM module.
2.1.3 DiskOnChip Installation
Please make sure the central polarization key on the socket, and place the DiskOnChip as the same
direction.

Chapter2 Installation
7
User’s Manual
2.2 Jumper Settings and Connectors
2.2.1 Board Outline of IAC-H670
VGA1 COM1
LAN1 PKM1
1
JP4
3
FAN2
PLRS1
1 10
1
2 10
9
SDOC1
FAN1
IDE1
DIM1
FDC1
KCN1
COM2
LPT1
DIO1
1
9
10
2
CMOS1
3
1
CON2
CON1
SC2T1
1
5
IRDA1
1 5
USBC1
1 9
10
2
USBC2
1 9
10
2
PSW1
1
2
JP6
1
3
1
8
ISP1
1
4
ATXC1
1
9
12 4
SC2T2

Chapter2 Installation
8 User’s Manual
2.2.2 Jumper Setting Summary of IAC-H670
LOCATION FUNCTION
CMOS1 Clear CMOS
SDOC1 Select DiskOnChip (Flash Disk) Address
SC2T1 / SC2T2 Select COM2 Type
JP4, JP6 Factory Use Only
CMOS1:Clear CMOS
COMS1 States CMOS1
Normal (Default) 1-2
CLEAR CMOS 2-3
CMOS1
CMOS1
1
2
3
Normal
(Default)
Clear CMOS
Note: If you forget your password, the onl
y
way to solve this problem is to discharge the
CMOS memory by turning power off and
placing a shunt on the COMS1 (2-3) for 5
seconds, then removing the shunt.

Chapter2 Installation
9
User’s Manual
SDOC1: Select DiskOnChip (Flash Disk) Address
Flash Disk Address SDOC1
CC00~CDFFH 1-2,9-10
D000~D1FFH 3-4,7-8
D400~D5FFH 3-4,9-10
D800~D9FFH 5-6,7-8
DC00~DDFFH 5-6,9-10
OFF (Default) 2-4,8-10
SC2T1/SC2T2: Select COM2 Type
COM2 Type SC2T2 SC2T1
RS-232 (Default) 1-5,2-6,3-7,4-8 1-2
RS-422 5-9,6-10,7-11,8-12 3-4
RS-485 5-9,6-10,7-11,8-12 5-6
SDOC1
SC2T2
SC2T1
D000~D1FFH
D800~D9FFH
DC00~DDFFH
D400~D5FFH
2
1
10
9
SDOC1
(
Default
)
CC00~CDFFH
SC2T1
2 1
6 5
9 1
4
12
RS-232
(
Default
)
RS-422
RS-485
SC2T2

Chapter2 Installation
10 User’s Manual
2.2.3 I/O Connector Summary
Connector Function
ATXC1 ATX Power Expansion (Header)
ATX Power ON Switch (Header)
KCN1 5pin Keyboard Cable Connector
PKM1 PS/2 Keyboard & Mouse Connector (Mini Din)
ISP1 Program ISP GAL Connector (Factory Only)
PLRS1 Connector for Power LED, Reset, Speaker Connector, HD LED
COM1 RS-232 Serial Port#1 Connector (D-Sub)
FAN1 System FAN Connector
FAN2 CPU FAN Connector
IRDA1 Consumer Remote Control IR (CIR)
VGA1 VGA Connector
USBC 1,2 USB Header
COM2 RS-232 Serial Port#2 Connector (Header)
IDE1 Primary IDE Cable Connector (Header)
DIO1 4bit Digital I/O Connector
LPT1 Parallel Port Connector (Header)
FDC1 Floppy Cable Connector (Header)
LAN1 LAN Connector
CON1 PC/104 Connector
CON2 PC/104 Connector
ATXC1: ATX Power Expansion Header
Pin No. Description
1 Ground
2 5V Standby
3 Ground
4 Power ON
ATXC1
4
1
ATXC1
Note: To have full features from ATX power, the
A
TXC1 should be wired to the connectors with the
same function on the Backplane. Please refer to the
connector definition and description for more
information.

Chapter2 Installation
11
User’s Manual
PSW1: ATX Power ON Switch (Header)
Pin No. Description
1 SWON-
2 Ground
KCN1: 5pin Keyboard Cable Connector
Pin No. Description
1 Keyboard Clock
2 Keyboard Data
3 NC
4 Ground
5 Stand By 5V
PKM1: PS/2 Keyboard & Mouse Connector(Mini Din)
Pin No. Description
1 PS/2 Keyboard Data
2 PS/2 Mouse Data
3 Ground
4 Stand By 5V
5 PS/2 Keyboard Clock
6 PS/2 Mouse Clock
PKM1
1
2
4
6 5
3
2
1
PSW1
KCN1
1 5
KCN1
PKM1
PSW1

Chapter2 Installation
12 User’s Manual
ISP1: Program ISP GAL Connector (Factory Only)
Pin No. Description
1 Vcc
2 SDO
3 SDI
4 ISP
5 NC
6 MODE
7 Ground
8 SCLK
PLRS1: Power LED, Reset, Speaker Connector
Pin No. Description
1 Power LED+
2 GND
3 HDD LED+
4 HDD LED-
5 RESET SW+
6 RESET SW-(GND)
7 External Speaker-
8 Internal Buzzer-
9 NC
10 External Speaker+
PLRS1
ISP1
1 8
ISP1
1 10
PLRS1
Default:7-8

Chapter2 Installation
13
User’s Manual
COM1: RS-232 Serial Port#1 Connector (D-Sub)
Pin No. Description
1 Data Carrier Detect (DCDA#)
2 Receive Data (RXDA)
3 Transmit Data (TXDB)
4 Data Terminal Ready (DTRA#)
5 Ground (GND)
6 Data Set Ready (DSRA#)
7 Request To Send (RTSA#)
8 Clear To Send (CTSA#)
9 Ring Indicator (RIA#)
FAN1: System FAN Connector
Pin No. Description
1 Ground
2 +12V
3 Fan Status Signal
COM1
1 5
9
6
FAN1
1
3
FAN1
COM1

Chapter2 Installation
14 User’s Manual
FAN2: CPU FAN Connector
Pin No. Description
1 Ground
2 +12V
3 Fan Status Signal
IRDA1: Consumer Remote Control IR (CIR)
Pin No. Description
1 +5V
2 NC
3 CIRRX
4 Ground
5 CIRTX
IRDA1
5
1
FAN2
1
3
FAN2
IRDA1