Lanner electronics MB-X66 Series User manual

MB-X66 Series
Socket 370 Processor (support
Tualatin) Network Security Appliance
Control Board, 6x Realtek 8139C
10/100M BASE-T Ethernet

COPYRIGHT©
This document is copyrighted by the original manufacture. The original manufacturer
reserves the right to make modifications to the product(s) described in this manual at any
time without notice. This manual may not, in whole or in part, be photocopied,
reproduced, transcribed, translated, or transmitted in whatever form without the written
consent of the manufacturer, except for copies retained by the purchaser for backup
purposes. All rights are reserved.
TRADEMARKS
Pentiumis a registered trademark of Intel Corporation.
The following are trademarks or registered trademarks of their respective companies:
IBM, Intel, AMD, Cyrix, Award, AMI, S3, Microsoft, Windows, Windows NT, Novell, SCO,
PC/104, PICMG, ALI, UMC, SMC, Winbond. Products mentioned in this manual are for
identification purposes only. All names of products or services appearing in this manual
are the trademarks or registered trademarks of their respective organizations and
companies.
Copyright 2003
Ver. No. 1.0
LEI-UM-MB-X66 Series
Date: 2003/01/08

TABLE OF CONTENTS
CHAPTER 1INTRODUCTION 1
1.1 SPECIFICATIONS 2
1.2 PACKING CHECK LIST 3
CHAPTER 2JUMPER SETTING AND CONNECTORS 4
2.1 BOARD OUTLINE OF MB-X66 4
2.2 INSTALLING AND UPGRADING THE CPU 5
2.3 JUMPER SETTING OVERVIEW 7
2.4 JUMPER LOCATIONS FOR MB-X66 8
2.5 JUMPER SETTINGS SUMMARY FOR MB-X66 9
2.6 JUMPER SETTINGS FOR MB-X66 10
2.7 I/O CONNECTOR LOCATIONS FOR MB-X66 11
2.8 I/O CONNECTOR SUMMARY FOR MB-X66 12
2.9I/O CONNECTORS DESCRIPTION 13
CHAPTER 3AMI BIOS SETUP 21
3.1 RUNNING AMI BIOS 21
3.2 AMI BIOS HIFLEX Setup Utility 22
3.3 STANDARD CMOS SETUP 24
3.4 Advanced CMOS Setup 26
3.5 Advanced Chipset Setup 30
3.6 POWER MANAGEMENT SETUP 34
3.7 PERIPHERAL SETUP 36
3.8 PCI PLUG AND PLAY SETUP 38
3.9 Hardware Monitor Setup 41
3.10 Auto-Detect Hard Disks 42
3.11 CHANGE SUPERVISOR/USER PASSWORD 44
3.12 Load High Performance Setup Defaults 46
3.13 SAVE & EXIT SETUP 47
3.14 EXIT WITHOUT SAVING 48

TABLE OF CONTENTS
CHAPTER 4DRIVERS SUPPORT 49
4.1 USE YOUR DRIVER CD-ROM 49
4.2FILE DIRECTORY 49
APPENDIX A TECHNICAL REFERENCE 50
GLOSSARY 52
TERMS AND CONDITIONS 58
RMA SERVICE REQUEST FORM 59

~ 1~
CHAPTER 1.
INTRODUCTION
The MB-X66 Series is a Socket 370 Pentium III network control board with six 10/100
Base-TX Ethernet ports specifically designed for Ethernet connectivity. It is suitable for
SOHO (Small Office, Home Office), SMB (Small Medium Business), ROBO (Remote
Office, Branch Office), applicationsdevelopers, system integrators, and service
providers segments..
With the Intel Pentium ® III processor, the MB-X66 Series support up to a blazing 1.26
GHz, to provide high performance and meets the requirements of network platform
appliances.
Targeting on the rapid growing network platform market, the MB-X66 Seriescomes with
six Realtek 8139C 10/100M Base-T Ethernet chips.Designed with the Plug-and-Serve
concept in mind, theMB-X66 Series offers one 168-DIMM socket support up to 100/133
MHz SDRAM which provide full functionality and performance to be used "exactly"
where you need it as well. In addition ,one ATA mode CompactFlash type II socket used
in installing OS avoiding service disruption caused by hard disk's mechanical/magnetic
failures.
MB-X66 Serieshas many expansion functionssuch as one PCI and one 124-pin Mini-
PCIslot ,One 40-pin and One 44-pin IDE connector, both two IDE ports that support up
to four IDE devices and Ultra ATA/100/66/33 interface help designers and integrators
improve system performance by retrieving and sending data faster. For easy access,
MB-X66 Series has a 9-pin, RS-232 serial port for local system management,
maintenance, and diagnostics. Everything you could need is on-board.

INTRODUCTION
~ 2~
1.1 SPECIFICATIONS
οProcessor :IntelPentium III/CeleronProcessor in Socket
370(133 MHz), support B-stepping
οChipset :Intel815EP chipset, IT8712F I/O Chipset
οEthernet : Six Realtek 8139C 10/100M BASE-T Ethernet,6 X
connector.
οExpansion Bus A. One 124-pinMini-PCI slot
B. One PCI Slot
οSystem Memory/RAM :One 25º 168pin DIMM Socket, support PC-100/133
MHz SDRAM
οIDE Drive Interface: A. One 40-pin IDE connector that support Ultra ATA100,
build in secondary master IDE Channel
B. One 44-pin (2x22, 2mm) IDE connector that
support Ultra ATA100, build in secondary slave IDE
Channel
C. One CompactFlash type II socket, support ATA
mode, build in primary master IDE Channel
οBIOS :AMIlicensed BIOS
οI/O Connector :A. Six RJ-45 external connectors
B. One RS-232 DB-9 connector
οReserved pin-header :A. Keyboard/Mouse pin-header
B. LAN LED pin deader
C. Power/Status LED header
D. one parallel port pin header (for control LCM use)
E. One 1*4 pin-header (for control Keypad use)
οRTC :Internal RTC with Li battery
οOperating Temperature :0 °C~60 °C
οStorage Temperature : -20 °C~70 °C
οHumidity :5 %~95%RH, non-condensing
οPower :On-board 12 pins AT power connector
οVersion :MB-X66A: Six Realtek 8139C10/100M BASE-T
Ethernet Adapter
MB-X66B: Four Realtek 8139C10/100M BASE-T
Ethernet Adapter

INTRODUCTION
~ 3~
1.2 PACKING CHECK LIST
Inspect the product package for the following items before installation. If there is anything
missing, please contact our authorized reseller.
Item Qty Remark
MB-X66A1 pc MB-X66ANetwork Control Board
MB-X66B1 pc MB-X66BNetwork Control Board

~ 4~
JUMPER SETTING AND CONNECTORS
The figure below shows the jumpers and connectors location on the MB-X66 Series. The
PCB version may differ for slight changes without notice.
2.1 Board Outline of MB-X66 Series
CHAPTER 2.
DLA3
PKMB1
DLA1
PSA1
DLA2
DLA6
DLA4
COMA1
FDCA1
IDEA1
CF1
FAN1
PCIB1
CFSL1
PCIA1
IDEB1
CMOS1
LAN6
FAN2
DLA5
PLRS1
1
11
ATXC1
1
4
2
43
44
1
LEDE1
IRDA1
5
1
LAN5
LAN4
KPA1
4
1
2
8
1
7
Intel
LAN3
LAN2
LAN1
5
6
2
1
SBVA1
PSW1
COMB1
LCMA1

JUMPER SETTING AND CONNECTORS
~ 5~
2.2 INSTALLING AND UPGRADING THE CPU
To upgrade to a higher power CPU, simply remove the old CPU and install a new one.
Make sure to set the jumpers for the new CPU type and speed.
WARNING!
Disconnect the power cord from your system when you intend to
work on it or when you plan to open the chassis of your industrial
computer. Do not make connections when the power is turned on
because the sensitive electronic components could be damaged
by the sudden rush of power. Please only allow experienced
electronic technicians to do this job.
STATIC ELECTRICITY PRECAUTION!
C
aution! Computer components are very sensitive to damage
from static electric discharge. Always ground yourself to remove
static charge build-
up before touching the boards in the computer.
Use a grounding wrist strap at all times. Place all electronic
components on anti-static pad for static-
dissipation or in
static-shielded bag when they are not in the chassis.
CAUTION!
Danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type recommended by the
manufactur
er. Dispose of used batteries according to the battery
manufacturer’s instructions or accepted environmental regulatory
standards.

JUMPER SETTING AND CONNECTORS
~ 6~
¥ INSTALLING THE DIMM MODULE:
A DIMM module simply snaps into a socket on the system board. Pin1 of the DIMM
module must correspond with Pin1 of the socket.
1.Pull the “tabs” which are at the ends of the socket to the side.
2.Position the DIMM above the socket with the “notches” in the module aligned with the
“keys” on the socket.
3.Seat the module vertically into the socket. Make sure it is completely seated. The tabs
will hold the DIMM in place.
Pin1 Notch
Key
TabTab

JUMPER SETTINGS AND CONNECTORS
~ 7~
2.3 JUMPER SETTING OVERVIEW
In order to select the operation modes of your system, configure and set the jumpers on
your SBC to match the needs of your applications. To set a jumper, a plastic cap
containing metal contacts is placed over the jumper pins as designated by the required
configuration as listed in this section. A jumper is said to be “ on ” or “ 1-2 ” when the
cap has been placed on two of its pins, as show in the figure below:
A pair of needle-nose pliers is recommended when working with jumpers. If you have
any doubts about the best hardware configuration for your application, contact our local
sales representative before you make any changes. In general, you simply need a
standard cable to make most connections

JUMPER SETTING AND CONNECTORS
~ 8~
2.4 JUMPER LOCATIONS FOR MB-X66 SERIES
DLA3
DLA1
DLA2
DLA6
DLA4
COMA1
CF1
PCIB1
CFSL1
CMOS1
LAN6
DLA5
LAN5
LAN4
Intel
LAN3
LAN2
LAN1
5
6
2
1
SBVA1
PSW1
1
3
1
2
1 3

JUMPER SETTING AND CONNECTORS
~ 9~
2.5 JUMPER SETTINGS SUMMARY FOR MB-X66 SERIES
JUMPER FUNCTION
CMOS1 Clear CMOS Data
DLA1~DLA6 LAN Disable/Enable 1x2 Pin 2.54mm
SCF1 Select Master/Slave
SBVA1 Select AT/ATX power 2x3 Pin 2.54mm

JUMPER SETTING AND CONNECTORS
~ 10 ~
2.6 JUMPER SETTINGS FOR MB-X66 SERIES
lCMOS1:Clear CMOS Data
CMOS1 Description
1-2Normal (Default)
2-3Clear CMOS
lDLA1~DLA6 ： LAN Disable/Enable 1x2 Pin 2.54mm
Pin Description
1VCC3
2GND
lCFSL1: Master/Slave Select
Compact Flash Card ATA Disk Chip SCF1
Master Slave 1-2
Slave Master 2-3 (Default)
lSBVA1 ： Select AT/ATX power 2x3 Pin 2.54mm
Pin No. Description PinNo. Description
1VCC 2VCC
35VSB 45VSB
5STB5V 6STB5V
Clear CMOS1
Normal (Default)
CMOS1
1
2
3
1
2
3
CMOS1
1
2
3
DLA1
1
2
SBVA1
6
2
1
5
CFSL
1
3
1

JUMPER SETTING AND CONNECTORS
~ 11 ~
2.7 I/O CONNECTOR LOCATIONS FOR MB-X66 SERIES
PKMB1
PSA1
COMA1
FDCA1
IDEA1
CF1
FAN1
PCIB1
PCIA1
IDEB1
LAN6
FAN2
PLRS1
1
11
ATXC1
1
4
2
43
44
1
LEDE1
IRDA1
5
1
LAN5
LAN4
KPA1
4
1
2
8
1
7
Intel
LAN3
LAN2
LAN1
PSW1
COMB1
LCMA1

JUMPER SETTING AND CONNECTORS
~ 12 ~
2.8 I/O CONNECTOR SUMMARY FOR MB-X66 SERIES
CONNECTOR FUNCTION
FAN1 3 Pin Fan Connector
FAN2 Fan Connector
LAN1-6LAN Connector
PSW1 For ATX Power Button
ATXC1 For ATX Function
KPA1 LCM Keypad
IrDA1 Alternate IrDA
PLRS1 Power LED, Reset, Speaker Connector
COMB1 Serial Port #2 Connector (Header)
COMA1RS232 Serial Port #1 Connector (D-Sub)
PSA1 20 Pin ATX Power Connector
PSB112 Pin Power Connector
LCMA1 LCM CONNECTOR
CF1 Compact Flash Connector
LEDE1 2x22 Pin
IDEA1IDE Connector (Header)
IDEB1IDE Connector (Header)
PKMB1 PS/2 Keyboard & Mouse Connecter

JUMPER SETTING AND CONNECTORS
~ 13 ~
2.9 I/O CONNECTORS DESCRIPTION
lFAN1/2 : 3 Pin FAN Connector
Pin No. Description
1Ground
2+12V
3FAN Status
lLANA1~LAN6 :Type 1 ( RJ-45 )
Pin No. Description
1TX+
2TX-
3RX+
4T45
5T45
6RX-
7T78
8T78
lPSW1: For ATX Power Button
Pin No. Description
1PANSW
2GND
lATXC1: For ATX Function
Pin No. Description
1GND
2+5V STANDBY
3GND
4PSON
lKPA1: LCM Keypad
Pin Description
1KPA1
2KPA2
3KPA3
4KPA4
LANA1
FAN1/2
1 2 3
ATXC1
1
4
KPA1
4
1
PSW1
1
2

JUMPER SETTING AND CONNECTORS
~ 14 ~
lIRDA1:Alternate IRDA
Pin No. Description
1+5V
2NC
3IRRX
4GND
5IRTX
lCOMA1: RS-232 Serial Port #1 Connector ( D-Sub )
Pin No. Description
1Data Carrier Detect ( DCDA # )
2Receive Data ( RXDA )
3Transmit Data ( TXDA )
4Data Terminal Ready ( DTRA # )
5Ground ( GND )
6Data Set Ready ( DSRA # )
7Request To Send ( RTSA # )
8Clear To Send ( CTSA # )
9Ring Indicator ( RIA # )
lPLRS1:Power LED,HD LED,Reset,Speaker Connector(11 Pin 2.54mm)
Pin No. Description
1Power LED +
2Power LED +
3GND
4HDD LED +
5HDD LED -
6RESET SW +
7RESET SW –(GND)
8External Speaker -
9Internal Buzzer -
10 NC
11 External Speaker +
IRDA1
5
1
Default :
8-9 (ON)
Internal Buzzer
1
11
PLRS1
COMA1
1 5
9 6

JUMPER SETTING AND CONNECTORS
~ 15 ~
lCOMB1: Serial Port #2 Connector ( Header )
Description
Pin No. RS-232
1Data Carrier Detect (DCDB #)
2Data Set Ready (DSRB #)
3Receive Data (RXDB)
4Request To Send (RTSB #)
5Transmit Data (TXDB)
6Clear To Send (CTSB#)
7Data Terminal Ready (DTRB #)
8Ring Indicator (RIB #)
9Ground
10 NC
lPKMB1: PS/2 Keyboard & Mouse Connector (2x4 Header 2.54mm )
Pin No. Description Pin No. Description
1KBCLK 2GND
3NC 4KBDATA
5NC 6MSDATA
7MSCLK 8VCC
lLCMA1: LCM Connector
Pin No. Description Pin No. Description
1VCC 2PGND
3LSTIN-4VEE
5LAFD-6LINIT-
7LPD1 8LPD0
9LPD3 10 LPD2
11 LPD5 12 LPD4
13 LPD7 14 LPD6
15 LCD 16 VCC
1
2
9
10
COMB1
2
4
6
8
1
3
5
7
PKM1
2
16
15
1
LCMA1

JUMPER SETTING AND CONNECTORS
~ 16 ~
lPSA1:20 Pin ATX Power Connector
Pin No. Description Pin No. Description
1+3.3V 11 +3.3V
2+3.3V 12 -12V
3GND 13 GND
4+5V 14 SWITCH
5GND 15 GND
6+5V 16 GND
7GND 17 GND
8Power Good 18 -5V
9Stand-By 5V 19 +5V
10 +12V 20 +5V
lPSB1: 12 Pin Power Connector
Pin No. Description
1PWG
2+5V
3+12V
4-12V
5GND
6GND
7GND
8GND
9-5V
10 +5V
11 +5V
12 +5V
PSA1
1
11
10
20
1
PSB1
12