Lantronix PREMIERWAVE XC HSPA+ User manual

Part Number 900-678-R
Revision A May 2013
PremierWave XC
HSPA+ User Guide
PRELIMINARY DRAFT
PRELIMINARY DRAFT

PremierWave XC HSPA+ User Guide 2
Copyright & Trademark
© 2013 Lantronix, Inc. All rights reserved. No part of the contents of this book may be transmitted
or reproduced in any form or by any means without the written permission of Lantronix.
Lantronix® registered trademark of Lantronix, Inc. DeviceInstaller and PremierWave© are
trademark of Lantronix, Inc.
Windows® and Internet Explorer® are registered trademarks of Microsoft Corporation. Mozilla®
and Firefox® are registered trademarks of the Mozilla Foundation. Chrome™ is a trademark of
Google, Inc. Opera™ is a trademark of Opera Software ASA. Tera Terma is a registered
trademark of Vector, Inc. All other trademarks and trade names are the property of their
respective holders.
Warranty
For details on the Lantronix warranty policy, please go to our web site at
www.lantronix.com/support/warranty.
Contacts
Lantronix Corporate Headquarters
167 Technology Drive
Irvine, CA 92618, USA
Toll Free: 800-526-8766
Phone: [phone]
Fax: [phone]
Technical Support
Online: www.lantronix.com/support
Sales Offices
For a current list of our domestic and international sales offices, go to the Lantronix web site at
www.lantronix.com/about/contact.
Disclaimer
The information in this guide may change without notice. The manufacturer assumes no
responsibility for any errors that may appear in this guide.
Revision History
Date Rev. Comments
May 2013 A Initial document for firmware release 7.7.0.0R27.
PRELIMINARY DRAFT
PRELIMINARY DRAFT

PremierWave XC HSPA+ User Guide 3
Table of Contents
List of Figures _____________________________________________________________9
List of Tables _____________________________________________________________10
1: Using This Guide 12
Purpose and Audience _____________________________________________________12
Summary of Chapters ______________________________________________________12
Additional Documentation ___________________________________________________13
2: Introduction 14
Key Features _____________________________________________________________14
Applications ______________________________________________________________14
Protocol Support _________________________________________________________14
Troubleshooting Capabilities _________________________________________________15
Configuration Methods _____________________________________________________15
Addresses and Port Numbers ________________________________________________16
Hardware Address _____________________________________________________16
IP Address ___________________________________________________________16
Port Numbers _________________________________________________________16
Product Information Label ___________________________________________________16
3: Installation of PremierWave XC HSPA+ 18
Package Contents _________________________________________________________18
User-Supplied Items _______________________________________________________18
Hardware Components ____________________________________________________18
Front/Top Panel _______________________________________________________18
Back Panel ___________________________________________________________23
Installing the PremierWave XC HSPA+ ________________________________________23
4: Using DeviceInstaller 25
Accessing PremierWave Using DeviceInstaller __________________________________25
Device Detail Summary _____________________________________________________25
5: Configuration Using Web Manager 27
Accessing Web Manager ___________________________________________________27
Device Status Page ____________________________________________________28
Web Manager Components _________________________________________________29
Navigating Web Manager ___________________________________________________30
PRELIMINARY DRAFT
PRELIMINARY DRAFT

PremierWave XC HSPA+ User Guide 4
6: Network Settings 32
Network 1 (eth0) Interface Settings ____________________________________________32
To Configure Network Interface Settings ____________________________________33
To View Network Interface Status _________________________________________33
Network 1 (Link) Settings ___________________________________________________34
To Configure Network Link Settings ________________________________________34
Network 1 (Failover) _______________________________________________________35
To Configure Network 1 Failover Settings ___________________________________35
Network 2 (Cellular) Settings ________________________________________________35
To Configure Network 2 (Cellular Interface) Settings ___________________________36
Network 2 (Link) Settings ___________________________________________________36
To Configure Link Settings _______________________________________________37
Gateway ________________________________________________________________37
WAN ________________________________________________________________37
To Configure Gateway WAN Settings ______________________________________38
Port Forwarding _______________________________________________________38
To Configure Gateway Port Forwarding Settings ______________________________38
Static Routes _________________________________________________________39
To Configure Gateway Static Route Settings _________________________________39
DHCP Server _________________________________________________________40
To Configure Gateway DHCP Server Settings ________________________________40
7: Cellular 41
To Configure Cellular Settings ____________________________________________41
8: Action Settings 42
Alarms and Reports _______________________________________________________42
Actions _________________________________________________________________42
To Configure Action Settings _____________________________________________43
Digital Input ______________________________________________________________44
To Configure Digital Input Settings _________________________________________44
9: Line and Tunnel Settings 45
Line Settings _____________________________________________________________45
To Configure Line Settings _______________________________________________46
To View Line Statistics __________________________________________________47
Tunnel Settings ___________________________________________________________47
Serial Settings ________________________________________________________47
To Configure Tunnel Serial Settings ________________________________________48
Packing Mode _________________________________________________________48
To Configure Tunnel Packing Mode Settings _________________________________49
Accept Mode __________________________________________________________49
PRELIMINARY DRAFT
PRELIMINARY DRAFT

PremierWave XC HSPA+ User Guide 5
To Configure Tunnel Accept Mode Settings __________________________________51
Connect Mode ________________________________________________________51
To Configure Tunnel Connect Mode Settings ________________________________52
Disconnect Mode ______________________________________________________52
To Configure Tunnel Disconnect Mode Settings ______________________________53
Modem Emulation ______________________________________________________53
To Configure Tunnel Modem Emulation Settings ______________________________54
Relay Output _____________________________________________________________54
To Configure Relay Settings ______________________________________________55
10: Terminal and Host Settings 56
Terminal Settings _________________________________________________________56
To Configure the Terminal Network Connection _______________________________57
To Configure the Terminal Line Connection __________________________________57
Host Configuration ________________________________________________________58
To Configure Host Settings ______________________________________________58
11: Services Settings 59
DNS Settings _____________________________________________________________59
To View or Configure DNS Settings: _______________________________________59
FTP Settings _____________________________________________________________59
To Configure FTP Settings _______________________________________________60
Syslog Settings ___________________________________________________________60
To View or Configure Syslog Settings: ______________________________________60
HTTP Settings ____________________________________________________________61
To Configure HTTP Settings _____________________________________________62
To Configure HTTP Authentication _________________________________________63
RSS Settings _____________________________________________________________63
To Configure RSS Settings ______________________________________________63
SNMP Settings ___________________________________________________________64
To Configure SNMP Settings _____________________________________________64
SMS ___________________________________________________________________64
Inbound SMS _________________________________________________________64
Outbound SMS ________________________________________________________65
To Configure SMS _____________________________________________________65
To Configure Outbound SMS _____________________________________________65
12: Security Settings 66
SSH Settings _____________________________________________________________66
SSH Server Host Keys __________________________________________________66
SSH Client Known Hosts ________________________________________________67
SSH Server Authorized Users ____________________________________________67
PRELIMINARY DRAFT
PRELIMINARY DRAFT

PremierWave XC HSPA+ User Guide 6
SSH Client Users ______________________________________________________68
To Configure SSH Settings ______________________________________________69
SSL Settings _____________________________________________________________69
Certificate and Key Generation ___________________________________________69
To Create a New Credential ______________________________________________70
Certificate Upload Settings _______________________________________________71
To Configure an Existing SSL Credential ____________________________________71
Trusted Authorities _____________________________________________________72
To Upload an Authority Certificate _________________________________________72
13: Maintenance and Diagnostics Settings 73
Filesystem Settings ________________________________________________________73
File Display ___________________________________________________________73
To Display Files _______________________________________________________73
File Modification _______________________________________________________74
File Transfer __________________________________________________________74
To Transfer or Modify Filesystem Files ______________________________________75
Protocol Stack Settings _____________________________________________________75
IP Settings ___________________________________________________________75
To Configure IP Network Stack Settings ____________________________________75
ICMP Settings _________________________________________________________76
To Configure ICMP Network Stack Settings __________________________________76
ARP Settings _________________________________________________________76
To Configure ARP Network Stack Settings __________________________________76
SMTP Settings ___________________________________________________________77
To Configure SMTP Network Stack Settings _________________________________77
To Configure ARP Network Stack Settings __________________________________77
Diagnostics ______________________________________________________________78
Hardware ____________________________________________________________78
To View Hardware Information ____________________________________________78
IP Sockets ___________________________________________________________78
To View the List of IP Sockets ____________________________________________78
Ping ________________________________________________________________78
To Ping a Remote Host _________________________________________________79
Traceroute ___________________________________________________________79
To Perform a Traceroute ________________________________________________79
Log _________________________________________________________________79
To Configure the Diagnostic Log Output ____________________________________80
Memory ______________________________________________________________80
To View Memory Usage _________________________________________________80
Processes ____________________________________________________________80
To View Process Information _____________________________________________80
Threads _________________________________________________________________81
PRELIMINARY DRAFT
PRELIMINARY DRAFT

PremierWave XC HSPA+ User Guide 7
To View Thread Information ______________________________________________81
Clock ___________________________________________________________________81
To Specify Clock Setting Method __________________________________________82
System Settings __________________________________________________________82
To Reboot or Restore Factory Defaults _____________________________________82
Discovery and Query Port ___________________________________________________83
To Configure Discovery _________________________________________________83
14: Advanced Settings 84
Email Settings ____________________________________________________________84
To View, Configure and Send Email ________________________________________84
Command Line Interface Settings _____________________________________________85
Basic CLI Settings _____________________________________________________85
To View and Configure Basic CLI Settings ___________________________________85
Telnet Settings ________________________________________________________86
To Configure Telnet Settings _____________________________________________86
SSH Settings _________________________________________________________86
To Configure SSH Settings ______________________________________________87
XML Settings _____________________________________________________________87
XML: Export Configuration _______________________________________________87
To Export Configuration in XML Format _____________________________________88
XML: Export Status _____________________________________________________88
To Export in XML Format ________________________________________________88
XML: Import Configuration _______________________________________________89
To Import Configuration in XML Format _____________________________________89
15: Security in Detail 91
Public Key Infrastructure ____________________________________________________91
TLS (SSL) _______________________________________________________________91
Digital Certificates _________________________________________________________91
Trusted Authorities ________________________________________________________91
Obtaining Certificates ______________________________________________________92
Self-Signed Certificates _____________________________________________________92
Certificate Formats ________________________________________________________92
OpenSSL ________________________________________________________________92
Steel Belted RADIUS ______________________________________________________93
Free RADIUS ____________________________________________________________93
16: Updating Firmware 94
Obtaining Firmware ________________________________________________________94
Loading New Firmware through Web Manager __________________________________94
Loading New Firmware through FTP __________________________________________95
PRELIMINARY DRAFT
PRELIMINARY DRAFT

PremierWave XC HSPA+ User Guide 8
17: Branding the PremierWave XC HSPA+ 96
Web Manager Customization ________________________________________________96
Short and Long Name Customization __________________________________________97
To Customize Short or Long Names _______________________________________97
Appendix A: Technical Specifications 98
Network _________________________________________________________________98
Cellular ______________________________________________________________98
Ethernet _____________________________________________________________98
Serial Interface ___________________________________________________________98
Serial Connector __________________________________________________________98
USB Interface ____________________________________________________________98
USB Connector ___________________________________________________________99
I/O Interface _____________________________________________________________99
Input ________________________________________________________________99
Output _______________________________________________________________99
I/O Connectors ___________________________________________________________99
LED Indicators ____________________________________________________________99
Security _________________________________________________________________99
Management ____________________________________________________________100
Software _______________________________________________________________100
Power _________________________________________________________________100
Environmental ___________________________________________________________100
Agency Approvals / Compliance _____________________________________________100
Dimensions _____________________________________________________________101
Warranty _______________________________________________________________101
Appendix B: Compliance 102
Appendix C: Technical Support 105
Appendix D: Binary to Hexadecimal Conversions 106
Converting Binary to Hexadecimal ___________________________________________106
Conversion Table _____________________________________________________106
Scientific Calculator ___________________________________________________106
Appendix E: USB-CDC-ACM Device Driver File
for Windows Hosts 108
PRELIMINARY DRAFT
PRELIMINARY DRAFT

PremierWave XC HSPA+ User Guide 9
List of Figures
Figure 2-1 PremierWave XC HSPA+Product Label ______________________________________17
Figure 3-1 PremierWave XC HSPA+ Top/Front View_____________________________________19
Figure 3-2 PremierWave Male DB9 DTE Serial Ports ____________________________________20
Figure 3-3 PremierWave Pinout Configuration for RS-232_________________________________20
Figure 3-4 PremierWave Pinout Configuration for Full Duplex RS-422/485 (4-wire______________20
Figure 3-5 PremierWave Pinout Configuration for Half Duplex RS-422/485 (2-wire)_____________20
Figure 3-11 PremierWave Dimensions in Inches (in) _____________________________________24
Figure 5-1 PremierWave XC HSPA+ Home Pages ______________________________________28
Figure 5-2 Components of the Web Manager Page ______________________________________29
Figure 16-1 Uploading New Firmware ________________________________________________94
PRELIMINARY DRAFT
PRELIMINARY DRAFT

PremierWave XC HSPA+ User Guide 10
List of Tables
Table 3-6 PremierWave LEDs and Descriptions ________________________________________21
Table 3-7 Cellular Signal Strength Indicator ___________________________________________21
Table 3-8 Diagnostic LED Indications ________________________________________________22
Table 3-9 PremierWave Bottom/Back Panel View _______________________________________23
Table 3-10 PremierWave XC HSPA+ Connections (Side) _________________________________23
Table 6-1 Network Interface Settings _________________________________________________32
Table 6-2 Network 1 (eth0) Link Settings ______________________________________________34
Table 6-3 WAN Configuration ______________________________________________________37
Table 6-4 Port Forwarding Rules List _________________________________________________38
Table 6-5 Adding a New Port Forwarding Rule _________________________________________38
Table 6-6 Adding a New Static Route ________________________________________________39
Table 6-7 DHCP Settings __________________________________________________________40
Table 6-8 Static Lease Listing ______________________________________________________40
Table 6-9 Add a Static Lease _______________________________________________________40
Table 8-1 Action Settings __________________________________________________________42
Table 8-2 Digital Input Settings _____________________________________________________44
Table 9-1 Line Configuration Settings ________________________________________________45
Table 9-2 Line Command Mode Settings ______________________________________________46
Table 9-3 Tunnel Serial Settings ____________________________________________________48
Table 9-4 Tunnel Packing Mode Settings _____________________________________________48
Table 9-5 Tunnel Accept Mode Settings ______________________________________________49
Table 9-6 Tunnel Connect Mode Settings _____________________________________________51
Table 9-7 Tunnel Disconnect Mode Settings ___________________________________________53
Table 9-8 Tunnel Modem Emulation Settings __________________________________________53
Table 9-9 Relay Output Settings ____________________________________________________55
Table 10-1 Terminal on Network and Line Settings ______________________________________56
Table 10-2 Host Configuration ______________________________________________________58
Table 11-1 DNS Settings __________________________________________________________59
Table 11-2 FTP Settings __________________________________________________________59
Table 11-3 Syslog Settings ________________________________________________________60
Table 11-4 HTTP Settings _________________________________________________________61
Table 11-5 HTTP Authentication Settings _____________________________________________62
Table 11-6 RSS Settings __________________________________________________________63
Table 11-7 SNMP Settings _________________________________________________________64
Table 11-8 Inbound SMS Settings ___________________________________________________64
Table 11-9 Outbound SMS Settings _________________________________________________65
PRELIMINARY DRAFT
PRELIMINARY DRAFT

PremierWave XC HSPA+ User Guide 11
Table 12-1 SSH Server Host Keys ___________________________________________________66
Table 12-2 SSH Client Known Hosts _________________________________________________67
Table 12-3 SSH Server Authorized Users _____________________________________________68
Table 12-4 SSH Client Users _______________________________________________________68
Table 12-5 Certificate and Key Generation Settings _____________________________________70
Table 12-6 Upload Certificate Settings _______________________________________________71
Table 12-7 Trusted Authority Settings ________________________________________________72
Table 13-1 File Display Settings ____________________________________________________73
Table 13-2 File Modification Settings _________________________________________________74
Table 13-3 File Transfer Settings ____________________________________________________74
Table 13-4 IP Network Stack Settings ________________________________________________75
Table 13-5 ICMP Network Stack Settings _____________________________________________76
Table 13-6 ARP Network Stack Settings ______________________________________________76
Table 13-7 SMTP Network Stack Settings _____________________________________________77
Table 13-8 Ping Settings __________________________________________________________78
Table 13-9 Traceroute Settings _____________________________________________________79
Table 13-10 Log Settings __________________________________________________________79
Table 13-11 Clock Settings ________________________________________________________81
Table 13-12 System Settings _______________________________________________________82
Table 13-13 Discovery Settings _____________________________________________________83
Table 14-1 Email Configuration _____________________________________________________84
Table 14-2 CLI Configuration Settings ________________________________________________85
Table 14-3 Telnet Settings ________________________________________________________86
Table 14-4 SSH Settings __________________________________________________________86
Table 14-5 XML Exporting Configuration ______________________________________________87
Table 14-6 Exporting Status ________________________________________________________88
Table 14-7 Import Configuration from Filesystem Settings ________________________________89
Table 17-1 Short and Long Name Settings ____________________________________________97
PRELIMINARY DRAFT
PRELIMINARY DRAFT

PremierWave XC HSPA+ User Guide 12
1: Using This Guide
Purpose and Audience
This guide provides the information needed to configure, use, and update the PremierWave XC
HSPA+. It is intended for software developers and system integrators who are installing this
product into their designs.
Summary of Chapters
The remaining chapters in this guide include:
Chapter Description
2: Introduction Main features of the product and the protocols it supports.
Includes technical specifications.
3: Installation of PremierWave XC
HSPA+ Instructions for installing the PremierWave XC HSPA+.
4: Using DeviceInstaller Instructions for viewing the current configuration using
DeviceInstaller.
5: Configuration Using Web Manager Instructions for accessing Web Manager and using it to configure
settings for the device.
6: Network Settings Instructions for configuring network settings.
7: Cellular Instructions for configuring cellular settings.
8: Action Settings Instructions for configuring alarm settings.
9: Line and Tunnel Settings Instructions for configuring and tunnel settings.
10: Terminal and Host Settings Instructions for configuring terminal and host settings.
11: Services Settings Instructions for configuring DNS, FTP, HTTP and Syslog settings.
12: Security Settings Instructions for configuring SSL security settings.
13: Maintenance and Diagnostics
Settings Instructions to maintain the , view statistics, files, and diagnose
problems.
14: Advanced Settings Instructions for configuring email, CLI and XML settings.
15: Security in Detail Provides additional information on security settings available.
16: Updating Firmware Instructions for obtaining the latest firmware and updating the .
17: Branding the PremierWave XC
HSPA+ Instructions on how to brand your device.
Appendix A: Technical Specifications Technical specifications for the device.
Appendix C: Technical Support Instructions for contacting Lantronix Technical Support.
Appendix D: Binary to Hexadecimal
Conversions Instructions for converting binary values to hexadecimals.
Appendix B: Compliance Lantronix compliance information.
Appendix E: USB-CDC-ACM Device
Driver File for Windows Hosts Information about the device driver file for windows host.
PRELIMINARY DRAFT
PRELIMINARY DRAFT

1: Using This Guide
PremierWave XC HSPA+ User Guide 13
Caution: To avoid electric shock and for the device to work properly, do not allow
cleaning solution to get inside the device, specifically the interface port
connectors, power connector, or power cord. Do not immerse the
device in any liquid.
Additional Documentation
Visit the Lantronix Web site at www.lantronix.com/support/documentation for the latest
documentation and the following additional documentation.
Document Description
PremierWave XC HSPA+
Command Reference Instructions for accessing Command Mode (the command line interface) using a Telnet connection, SSH connection or through the
port. Detailed information about the commands. Also provides details
for XML configuration and status.
PremierWave XC HSPA+ Quick
Start Guide Instructions for getting the PremierWave up and running.
DeviceInstaller Online Help Instructions for using the Lantronix Windows-based utility to locate the
PremierWave and to view its current settings.
PRELIMINARY DRAFT
PRELIMINARY DRAFT

PremierWave XC HSPA+ User Guide 14
2: Introduction
PremierWave XC HSPA+ is a multi-port device server offering ethernet and cellular connectivity
for remote access and easy management of machines or equipment over the network and across
the internet.
Key Features
Power Supply: 9-30VDC input voltage through locking barrel connector. 12V wall cube
power supply included with unit.
Controller: 32-bit ARM9 microprocessor running at 400 megahertz (Mhz) with 16 Kilobytes
(KB) Data Cache and 16 KB of Instruction Cache.
Memory: 128 MB SDRAM, 64 MB NAND Flash, and 8 MB serial SPI Flash.
Serial Ports: Two 300 to 921 kbaud, RS-232/422/485 serial ports providing serial to Ethernet
and serial to cellular tunneling
Ethernet to cellular routing
UMTS HSPA+
Digital Inputs: two configurable inputs suitable for TTL input levels, and tolerant of up to
30VDC input voltages that can trigger alerts.
Relay Outputs: 1 independently isolated mechanical form-C relay
Ethernet: 1 Port Ethernet 10Base-T or 100Base-TX (auto-sensing for speed, duplex and
cross-over CAT5 cable)
USB Ports: One 2.0 high speed USB port for device management and configuration
Temperature Range: Operating temperature at -40° to +70°C. Storage temperature at -40° to
+85°C.
Applications
The PremierWave XC HSPA+ device server connects serial devices such as those listed below to
Ethernet and Cellular networks using the IP protocol family.
Patient Monitoring Devices
Glucose Analyzers
Infusion Pumps
Protocol Support
The PremierWave XC HSPA+ device server contains a full-featured IP stack. Supported protocols
include:
HSPA+, UMTS, EDGE, GSM, GPRS
PRELIMINARY DRAFT
PRELIMINARY DRAFT

2: Introduction
PremierWave XC HSPA+ User Guide 15
ARP, HTTP, HTTPS, SMTP AUTH, SNMP v1/v2c/v3, Modbus TCP, UDP/IP, TCP/IP, SSH,
SSL, TLS, RSS, UPnP, ICMP, BOOTP, DHCP, Auto IP, Telnet, SNTP, FTP, FTPS, DNS,
TFTP, XML and Syslog for network communications and management.
TFTP for uploading/downloading files.
FTP and HTTP/HTTPS web server for firmware upgrades and uploading/downloading files.
TCP/IP, UDP/IP, Telnet, SSH, SSL, TCP AES and UDP AES for command/response based
data acquisition application or alarm triggered connection
HTTP/HTTPS web based monitoring of input readings, chart and data logging
SMTP AUTH, HTTP/HTTPS Post, FTP/FTPS Put and SNMP Traps for alarm triggered
notification
SNTP for device clock synchronization
SMS for alarm triggered notification.
Troubleshooting Capabilities
The PremierWave XC HSPA+ offers a comprehensive diagnostic toolset that lets you troubleshoot
problems quickly and easily. Available from the CLI or Web Manager, the diagnostic tools let you:
View memory and IP socket information.
Perform ping and traceroute operations.
Conduct forward or reverse DNS lookup operations.
View all processes currently running on the PremierWave, including CPU utilization.
View system log messages.
Configuration Methods
After installation, the PremierWave requires configuration. For the unit to operate correctly on a
network, it must have a unique IP address on the network. There are four basic methods for
logging into the PremierWave and assigning IP addresses and other configurable settings:
Web Manager: View and configure all settings easily through a web browser using the
Lantronix Web Manager. (See “Configuration Using Web Manager” on page 27.)
DeviceInstaller: Configure the IP address and related settings and view current settings on
the PremierWave using a Graphical User Interface (GUI) on a PC attached to a network. You
will need the latest version of DeviceInstaller. (See “Using DeviceInstaller” on page 25.)
Command Mode: There are two methods for accessing Command Mode (CLI): making a
Telnet or SSH connection, or connecting a PC or other host running a terminal emulation
program to the unit’s USB port. (See the PremierWave XC HSPA+ Command Reference
Guide for instructions and available commands.)
XML: The PremierWave supports XML-based configuration and setup records that make
device configuration transparent to users and administrators. XML is easily editable with a
standard text or XML editor. (See the PremierWave XC HSPA+ Command Reference Guide
for instructions and commands.)
PRELIMINARY DRAFT
PRELIMINARY DRAFT

2: Introduction
PremierWave XC HSPA+ User Guide 16
Addresses and Port Numbers
Hardware Address
The hardware address is also referred to as the Ethernet address, physical address, or MAC
address. Sample hardware address:
00-80-A3-14-1B-18
00:80:A3:14:1B:18
IP Address
Every device connected to an IP network must have a unique IP address. This address references
the specific unit.
Port Numbers
Every TCP connection and every UDP datagram is defined by a destination and source IP
address, and a destination and source port number. For example, a Telnet server commonly uses
TCP port number 23.
The following is a list of the default server port numbers running on the :
TCP Port 22: SSH Server (Command Mode configuration)
TCP Port 23: Telnet Server (Command Mode configuration)
TCP Port 80: HTTP (Web Manager configuration)
TCP Port 21: FTP
UDP Port 30718: LDP (Lantronix Discovery Protocol) port
TCP/UDP Port 10001: Tunnel 1 (see note below)
UDP Port 1900 and TCP Port 30179: UPnP
Note: Additional TCP/UDP ports and tunnels will be available, depending on the product
type. The default numbering of each additional TCP/UDP port and corresponding tunnel
will increase sequentially (i.e., TCP/UDP Port 1000X: Tunnel X).
Product Information Label
The product information label on the unit contains the
following information about the specific unit:
Bar code
Product Revision
Part Number
Serial Number (MAC Address)
Manufacturing Date Code
Note: The hardware address on the
label is also the product serial number.
The hardware address on the label is the
address for the Ethernet (eth0) interface.
PRELIMINARY DRAFT
PRELIMINARY DRAFT

2: Introduction
PremierWave XC HSPA+ User Guide 17
Figure 2-1 PremierWave XC HSPA+Product Label
Part Number
Revision
Serial Number
Country of Origin
Data Code
IMEI Text
PRELIMINARY DRAFT
PRELIMINARY DRAFT

PremierWave XC HSPA+ User Guide 18
3: Installation of PremierWave XC HSPA+
This chapter describes how to install the PremierWave XC HSPA+ device server. It contains the
following sections:
Package Contents
User-Supplied Items
Hardware Components
Installing the PremierWave XC HSPA+
Package Contents
The PremierWave XC HSPA+ package includes the following items:
One PremierWave XC HSPA+ device
One Power Supply 12 VDC with international adapters
Two External Antenna, SMA Connector
One RJ-45 Ethernet Straight Cat5 Cable, 1.5 meter
Quick Start Guide
User-Supplied Items
To complete your installation, you need the following items:
RS-232/422/485 serial devices and sensors that require network connectivity.
A serial cable, as listed below, for each serial device. One end of the cable must have a
female DB9 connector for the serial port.
- A null modem cable to connect the serial port to another DTE device.
- A straight-through modem cable to connect the serial port to a DCE device.
An available connection to your Ethernet network and an Ethernet cable.
A working AC power outlet if the unit will be powered from an AC power adapter.
SIM card
Hardware Components
Front/Top Panel
Figure 3-1 shows the top panel view of the PremierWave. Table 3-6, Table 3-7 and Table 3-8 list
and explain the behavior of the LEDs on the top panel.
LED Indicators: 2 ethernet LEDs, 1 diagnostic LED, one USB LED, one cellular status LED,
two serial activity LEDs, 5 signal strength LEDS, two of which are dual-colored.
PRELIMINARY DRAFT
PRELIMINARY DRAFT

3: Installation of PremierWave XC HSPA+
PremierWave XC HSPA+ User Guide 19
Figure 3-1 PremierWave XC HSPA+ Top/Front View
The PremierWave has two male DB9 serial ports that support RS-232/422/485. Figure 3-2 shows
the front view of the device. The default serial port settings are 9600 baud, 8 bits, no parity, 1 stop
bit, no flow control.
Signal
Strength
LEDs
Diagnostic
LED
PRELIMINARY DRAFT
PRELIMINARY DRAFT

3: Installation of PremierWave XC HSPA+
PremierWave XC HSPA+ User Guide 20
Figure 3-2 PremierWave Male DB9 DTE Serial Ports
Figure 3-3 PremierWave Pinout Configuration for RS-232
Figure 3-4 PremierWave Pinout Configuration for Full Duplex RS-422/485 (4-wire
Figure 3-5 PremierWave Pinout Configuration for Half Duplex RS-422/485 (2-wire)
Serial Serial Reset USB
1 2 Button Port
PRELIMINARY DRAFT
PRELIMINARY DRAFT