Lantronix PremierWave XC Installation manual

Part Number 900-599
Revision B May 2014
PremierWave XC
Intelligent Gateway
Command Reference

PremierWave® XC Intelligent Gateway Command Reference 2
Intellectual Property
© 2014 Lantronix, Inc. All rights reserved. No part of the contents of this book may be transmitted
or reproduced in any form or by any means without the written permission of Lantronix.
Lantronix and PremierWave are registered trademarks of Lantronix, Inc. in the United States and
other countries. DeviceInstaller is atrademark of Lantronix, Inc. U.S. Patents 8,024,446;
8,219,661; 7,698,405. Additional patents pending.
Windows and Internet Explorer are a registered trademarks of Microsoft Corporation. Mozilla and
Firefox are registered trademarks of the Mozilla Foundation. Chrome is a trademark of Google
Inc. All other trademarks and trade names are the property of their respective holders.
Contacts
Lantronix, Inc. Corporate Headquarters
167 Technology Drive
Irvine, CA 92618, USA
Toll Free: 800-526-8766
Phone: [phone]
Fax: [phone]
Technical Support
Online: www.lantronix.com/support
Sales Offices
For a current list of our domestic and international sales offices, go to the Lantronix web site at
www.lantronix.com/about/contact.
Disclaimer
The information in this guide may change without notice. The manufacturer assumes no
responsibility for any errors that may appear in this guide.
Revision History
Date Revision Comments
June 2012 A Initial document for firmware release 7.2.0.0.
May 2014 BUpdated for firmware release 7.8.0.0.

PremierWave® XC Intelligent Gateway Command Reference 3
Table of Contents
Intellectual Property ________________________________________________________2
Contacts _________________________________________________________________2
Disclaimer ________________________________________________________________2
Revision History ___________________________________________________________2
List of Figures _____________________________________________________________4
List of Tables ______________________________________________________________5
1: About This Guide 6
Chapter Summaries ________________________________________________________6
Conventions ______________________________________________________________6
Additional Documentation ____________________________________________________7
2: Overview 8
XML Architecture and Device Control ___________________________________________8
Command Line Interface _____________________________________________________8
3: Command Line Interface 9
Configuration Using Telnet ___________________________________________________9
Configuration Using Serials ___________________________________________________9
Navigating the CLI Hierarchy ________________________________________________10
Using Keyboard Shortcuts and CLI ____________________________________________11
Understanding the CLI Level Hierarchy ________________________________________11
4: Configuration Using XML 14
XML Configuration Record Document Type Definition _____________________________14
Quick Tour of XML Syntax __________________________________________________15
Declaration ___________________________________________________________15
Element Start and End Tags _____________________________________________15
Element Attributes _____________________________________________________15
Record, Group, Item, and Value Tags _________________________________________16
Importing and Exporting an XML Configuration File _______________________________18
Best Practices ____________________________________________________________18
Importing _____________________________________________________________18
Exporting ____________________________________________________________19
XML Configuration Groups __________________________________________________20
XML Status Record Groups and Items _________________________________________35
5: Commands and Levels 45

PremierWave® XC Intelligent Gateway Command Reference 4
List of Figures
Figure 3-2 CLI Level Hierarchy______________________________________________________12
Figure 3-3 Login Level Commands___________________________________________________13
Figure 3-4 Enable Level Commands__________________________________________________13
Figure 4-1 DTD for XCRs __________________________________________________________14
Figure 4-2 XML Example __________________________________________________________15
Figure 4-3 XML Example __________________________________________________________16
Figure 4-4 XML Example of Multiple Named Values _____________________________________16
Figure 4-5 XML Example of Multiple Items_____________________________________________17
Figure 4-6 XML Example with Multiple Groups__________________________________________17

PremierWave® XC Intelligent Gateway Command Reference 5
List of Tables
Table 3-1 Keyboard Shortcuts ______________________________________________________11
Table 4-7 XCR Groups ____________________________________________________________20
Table 4-8 XSR Group and Items ____________________________________________________35
Table 5-1 Commands and Levels____________________________________________________52

PremierWave® XC Intelligent Gateway Command Reference 6
1: About This Guide
This guide describes how to configure the PremierWave XC intelligent gateway using the
Command Line Interface (CLI) and/or Extensible Markup Language (XML). CLI provides an
interactive mode for accessing the device configuration and management interface. It is most
suited for system and network administrators comfortable with using similar interfaces on
Enterprise IT and Networking products. It is also helpful as a quick tool for access via the
product's serial ports or console/management ports.
XML provides an extensible mode for software developers interfacing with the device and system
integrators performing batch provisioning/updates.
Chapter Summaries
This table lists and summarizes content of each chapter.
Conventions
The table below lists and describes the conventions used in this book.
Chapter Summary
Chapter 2: Overview Gives an overview of CLI and XML.
Chapter 3: Command Line Interface Lists commands and describes how to use CLI to configure the
PremierWave XC device.
Chapter 4: Configuration Using XML Lists XCR groups and items and describes how to use XCRs to
configure the PremierWave XC device.
Chapter 5: Commands and Levels Provides an index of the CLI Command Hierarchy with hyperlinks
to the corresponding command details.
Convention Description
Bold text Default parameters.
Italic text Required values for parameters
Brackets [ ] Optional parameters.
Angle Brackets < > Possible values for parameters.
Pipe | Choice of parameters.
Warning Warning: Means that you are in a situation that could cause
equipment damage or bodily injury. Before you work on any
equipment, you must be aware of the hazards involved with electrical
circuitry and familiar with standard practices for preventing accidents.
Note Note: Means take notice. Notes contain helpful suggestions, information,
or references to material not covered in the publication.
Caution Caution: Means you might do something that could result in faulty
equipment operation, or loss of data.
Screen Font
(Courier New) CLI terminal sessions and examples of CLI input.

1: About This Guide
PremierWave® XC Intelligent Gateway Command Reference 7
Additional Documentation
Visit the Lantronix website at www.lantronix.com/support/documentation for the latest
documentation and the following additional documentation.
Document Description
PremierWave XC Intelligent
Gateway User Guide Describes how to configure and use the PremierWave XC device.
PremierWave XC Quick Start
Guide Instructions for getting the PremierWave XC up and running.
Com Port Redirector
Quick Start and Online Help Instructions for using the Lantronix Windows-based utility to create virtual com ports.
DeviceInstaller Online Help Instructions for using the Lantronix Windows-based utility to locate
the PremierWave XC device and to view its current settings.

PremierWave® XC Intelligent Gateway Command Reference 8
2: Overview
PremierWave XC intelligent gateway supports three convenient configuration methods: Web
Manager, Command Line Interface (CLI) and Extensible Markup Language (XML). For more
information about the Web Manager, see the PremierWave XC Intelligent Gateway User Guide on
the Lantronix website.
XML Architecture and Device Control
XML is a fundamental building block for the future growth of Machine-to-Machine (M2M) networks.
PremierWave XC device supports XML configuration records that make configuring the intelligent
gateway easy for users and administrators. XML configuration records are easy to edit with a
standard text editor or an XML editor.
For a brief overview of XML, see Chapter 4: Configuration Using XML. It provides rules on basic
XML syntax, a guide to the specific XML tags used, and a guide to using XML configuration
records.
Command Line Interface
Making the edge-to-enterprise vision a reality, the PremierWave XC intelligent gateway uses
industry-standard tools for configuration, communication, and control. For example, the
PremierWave XC device uses a command line interface (CLI) whose syntax is very similar to that
used by data center equipment such as routers and hubs.
For details of the CLI, see Chapter 5: Commands and Levels. It provides an index of the CLI
Command Hierarchy with links to the corresponding command details. The CLI provides
commands for configuring, monitoring, and controlling the intelligent gateway.

PremierWave® XC Intelligent Gateway Command Reference 9
3: Command Line Interface
This chapter describes accessing the PremierWave XC intelligent gateway by using Telnet, SSH,
or USB serial ports to configure the device, navigating the Command Line Interface (CLI), typing
keyboard shortcuts, and moving between the levels.
It contains the following sections:
Configuration Using Telnet
Configuration Using Serials
Navigating the CLI Hierarchy
Using Keyboard Shortcuts and CLI
Understanding the CLI Level Hierarchy
Refer to Chapter 5: Commands and Levels for a complete list of levels, commands, and
descriptions.
Configuration Using Telnet
To access and configure the intelligent gateway by using a Telnet session over the network, you
must first establish a Telnet connection. You can also establish a Telnet connection by clicking the
Telnet Configuration tab in the DeviceInstaller utility. See the DeviceInstaller Online Help for more
information, available on our website www.lantronix.com/support/downloads.
To access the PremierWave XC intelligent gateway by using Telnet, perform the following steps.
1. Click Start > Run. The Run dialog box displays.
2. Type cmd in the dialog box and press OK.
3. Type telnet x.x.x.x (x.x.x.x is the IP address) in a Windows/Linux command prompt.
The PremierWave XC device is online when the command prompt (>) displays. You are at the
root level of the CLI.
Note: Depending on the level of security, a password may be required.
Configuration Using Serials
Serial Command Mode
The serial port can be configured to operate in command mode permanently or to be triggered
under specified conditions. See the line <line> Level command description for more
information.
Intelligent Gateway Serial Recovery
Serial Recovery mode will temporarily override the line and tunnel settings for the serial line to
allow configuration changes to be made. The line and tunnel settings will be restored once the
user exits the Serial Recovery mode CLI.

3: Command Line Interface
PremierWave® XC Intelligent Gateway Command Reference 10
To configure the Lantronix locally using a serial port:
1. Connect a terminal or a PC running a terminal emulation program to one of the 's serial ports.
2. Configure the terminal to the following settings:
9600 baud
8-bit
No parity
1 stop bit
No flow control.
3. Power off the device.
4. Press and hold down the exclamation point (!) key.
5. Power on the device. After about 1 seconds, the exclamation point will display on the terminal
or PC screen.
6. Type xyz within 5 seconds to display the CLI prompt.
Navigating the CLI Hierarchy
The CLI is organized into a hierarchy of levels. Each level has a group of commands for a specific
purpose. For example, to configure a setting for the FTP server, one would navigate to the FTP
level, which is under the configuration level.
To move to a different level—Enter the name of the level from within its parent level. For
example, to enter the tunnel level, type tunnel <number> at the enable prompt. This
displays: <enable> tunnel <number>#.
To exit and return to one level higher—Type exit and press the Enter key. Typing exit at the
login level or the enable level will close the CLI session. If Line - Command Mode is specified
as Always, a new session starts immediately.
To view the current configuration at any level—Type show.
To view the list of commands available at the current level—Type the question mark "?". Items
within < > (e.g. <string>) are required parameters.
To view the available commands and explanations—Type the asterisk (*).
To view the list of commands available for a partial command—Type the partial command
followed by the question mark "?". For example: <tunnel-1>#show? displays a list of all
show commands at the tunnel level.
To view available commands and their explanations for a partial command—Type the partial
command followed by the asterisk (*). For example: <tunnel-1>#show* displays a list of all
show commands and descriptions at the tunnel level.
To view the last 20 commands entered at the CLI—Type show history.

3: Command Line Interface
PremierWave® XC Intelligent Gateway Command Reference 11
Using Keyboard Shortcuts and CLI
One useful shortcut built into PremierWave XC intelligent gateway is that the complete text of a
command does not have to be entered to issue a command. Typing just enough characters to
uniquely identify a command, then hitting enter, can be used as a short cut for a command. For
example, at the enable level, "sh" can be used for the "show" command.
Tab Completion is also available using the Tab and Enter keys on the keyboard. Typing the first
few characters of a command, then hitting the Tab key displays the first command that begins with
those characters. Hitting the Tab key again displays the next command that begins with the
original characters typed. You can press Enter to execute the command or you can backspace to
edit any parameters.
The following key combinations are allowed when configuring the intelligent gateway using the
CLI:
Table 3-1 Keyboard Shortcuts
Understanding the CLI Level Hierarchy
The CLI hierarchy is a series of levels. Arranging commands in a hierarchy of levels provides a
way to organize and group similar commands, provide different levels of security, and reduce the
complexity and number commands and options presented to a user at one time.
When you start a command line session, you begin at the login level. This level can be password
protected and provides access to high level status, a few diagnostic commands, and the enable
level. Further device information and configuration are accessed via the enable level.
The enable level can also be password protected and is the gateway to full configuration and
management of the intelligent gateway. There are commands for gathering and effecting all
elements of device status and configuration, as well as commands that take you to additional
levels. For instance, tunnel specific status and configuration is found under the "tunnel" level, and
network specific status and configuration commands are found under the "configuration" level.
Key Combination Description
Ctrl + a Places cursor at the beginning of a line
Ctrl + b Backspaces one character
Ctrl + d Deletes one character
Ctrl + e Places cursor at the end of the line
Ctrl + f Moves cursor forward one character
Ctrl + k Deletes from the current position to the end of the line
Ctrl + l Redraws the command line
Ctrl + n Displays the next line in the history
Ctrl + p Displays the previous line in the history
Ctrl + u Deletes entire line and places cursor at start of prompt
Ctrl + w Deletes one word back
Ctrl + z Exits the current CLI level
Esc + b Moves cursor back one word
Esc + f Moves cursor forward one word

3: Command Line Interface
PremierWave® XC Intelligent Gateway Command Reference 12
An overview of the levels in the PremierWave XC intelligent gateway is presented in Figure 3-2
CLI Level Hierarchy below.
Figure 3-2 CLI Level Hierarchy
Commands at the login level (see Figure 3-3 Login Level Commands below) do not affect current
configuration settings and are not displayed initially. If you type ?, you will see the login sub-
commands. These commands provide diagnostic and status information only.
(login) enable
ssl
ftp
http
if 2 (wwan0)
line <line>
filesystem
configure
device
digital input <number>
state change
eth0 link state change
icmp
dns
dhcp server
email <number>
ssh
arp
action
cli
clock
diagnostics
digital inputs
host <number>
if 1 (eth0)
sms
rss
ip
tunnel <line>
xml
client
server
credentials
trusted authorities
accept
connect
disconnect
modem
packing
serial
discovery
gateway
cellular
wwan0 link state
change
smtp
terminal <line>
snmp
syslog
ssh
telnet
ntp
log
digital input <number>
port forwarding
rule <number>
static route <number>
failover
link
link
inbound
outbound
snmpd
terminal network
ddns
mac address filter
<number>
qos
qos
traps
password
host <number>
relays

3: Command Line Interface
PremierWave® XC Intelligent Gateway Command Reference 13
Figure 3-3 Login Level Commands
>?
clrscrn exit
iperf <params> ping <host>
ping <host> <count> ping <host> <count> <timeout>
show show history
trace route <host> trace route <host> <protocol>
enable
>
Note: To configure the PremierWave XC intelligent gateway, you must be in the enable
level and any of its sub-levels. Figure 3-4 below shows the enable level commands.
Figure 3-4 Enable Level Commands
>enable
(enable)#?
auto show interfaces auto show processes
clrscrn configure
connect connect line <line>
device disable
dns email <number>
exit filesystem
iperf <params> kill ssh <session>
kill telnet <session> line <line>
ping <host> ping <host> <count>
ping <host> <count> <timeout> reload
reload factory defaults show
show history show interfaces
show ip sockets show processes
show sessions ssh
ssh <optClientUsername> <host> ssh <optClientUsername> <host>
<port>
ssl telnet <host>
telnet <host> <port> trace route <host>
trace route <host> <protocol> tunnel <line>
write xml
(enable)#
See the Chapter 5: Commands and Levels at the end of this document for a complete list of levels,
commands, and descriptions.

PremierWave® XC Intelligent Gateway Command Reference 14
4: Configuration Using XML
The PremierWave XC intelligent gateway provides an Extensible Markup Language (XML)
interface that you can use to configure PremierWave XC devices. Every configuration setting that
can be issued from the intelligent gateway Web Manager and CLI can be specified using XML.
The intelligent gateway can import and export configuration settings as an XML document known
as an XML Configuration Record (XCR). An XCR can be imported or exported via the CLI, a Web
browser, FTP, or the PremierWave XC filesystem. An XCR can contain many configuration
settings or just a few. For example, it might change all of the configurable parameters for a
intelligent gateway, or it may only change the baud rate for a single serial line. Using XCRs is a
straightforward and flexible way to manage the configuration of multiple PremierWave XC devices.
XML Configuration Record Document Type Definition
An XML document type definition (DTD) is a description of the structure and content of an XML
document. It verifies that a document is valid. XCRs are exported using the DTD as shown in
Figure 4-1 DTD for XCRs.
Figure 4-1 DTD for XCRs
<!DOCTYPE configrecord [
<!ELEMENT configrecord (configgroup+)>
<!ELEMENT configgroup (configitem+,configgroup*)>
<!ELEMENT configitem (value+)>
<!ELEMENT value (#PCDATA)>
<!ATTLIST configrecord version CDATA #IMPLIED>
<!ATTLIST configgroup name CDATA #IMPLIED>
<!ATTLIST configgroup instance CDATA #IMPLIED>
<!ATTLIST configitem name CDATA #IMPLIED>
<!ATTLIST value name CDATA #IMPLIED>
]>
The PremierWave device DTD rules state the following:
The XML document element is a <configrecord> element. This is the root element.
A <configrecord> must have one or more <configgroup> elements and can have a
version attribute.
A <configgroup> must have one or more <configitem> elements and can have name
and instance attributes.
A <configitem> element must have one or more <value> elements and can have a name
attribute.
A <value> element can have only data and can have a name attribute.
The name attribute identifies a group, item, or value. It is always a quoted string.
The instance attribute identifies the specific option, like the serial port number. The "instance"
attribute is always a quoted string.

4: Configuration Using XML
PremierWave® XC Intelligent Gateway Command Reference 15
Note:
The name for each <configgroup> (specified with the name attribute) is the group
name listed in the Web Manager XCR groups or with the "xcr list" CLI command. See
the PremierWave XC Intelligent Gateway User Guide for more information about the
XCR groups.
An empty or missing <value> element in each present <configgroup> clears the
setting to its default.
Quick Tour of XML Syntax
Declaration
The first line, <?xml version="1.0" standalone="yes"?>, is called the XML declaration.
It is required and indicates the XML version in use(normally version 1.0). The remainder of the file
consists of nested XML elements, some of which have attributes and content.
Element Start and End Tags
An element typically consists of two tags: start tag and an end tag that surrounds text and other
elements (element content). The start tag consists of a name surrounded by angle brackets, for
example <configrecord>. The end tag consists of the same name surrounded by angle
brackets, but with a forward slash preceding the name, for example </configrecord>. The
element content can also contain other "child" elements.
Element Attributes
The XML element attributes that are name-value pairs included in the start tag after the element
name. The values must always be quoted, using single or double quotes. Each attribute name
should appear only once in an element.
Figure 4-2 shows an XML example which consists of a declaration (first line), nested elements with
attributes and content.
Figure 4-2 XML Example
<?xml version=”1.0” standalone=”yes”?>
<configrecord>
<configgroup name = “serial command mode” instance = “1”>
<configitem name = “mode serial string”>
<value>disable</value>
</configitem>
</configgroup>
</configrecord>
The PremierWave XC device uses the attributes in the following subsections to label the group
configuration settings.

4: Configuration Using XML
PremierWave® XC Intelligent Gateway Command Reference 16
Record, Group, Item, and Value Tags
A <configgroup> is a logical grouping of configuration parameters and must contain one or
more <configitem> elements. It must have a name attribute and may have an instance
attribute.
A <configitem> is a specific grouping of configuration parameters relevant to its parent group.
An item takes the name attribute and must contain one or more value elements. For example,the
line group might have parameters such as baud rate, data bits, and parity.
A value may specify the value of a configuration parameter. It may contain the name attribute. In
this example, avalue of 9600 might be specified for baud rate; 7 may be specified for data bits, and
even may be specified for parity
A name attribute identifies the group, item, or value. It is always quoted (as are all XML attributes).
For example,a group that contains serial port parameters has the name "line"
An instance attribute identifies which of several instances is being addressed. It is always quoted.
For example,the serial port name (in the line configgroup) has the instance "1" to indicate serial
port 1 or "2" to specify serial port 2
The following figures show examples of XML configuration records and the use of the
<configrecord>, <configgroup>, <configitem>, and <value> XML elements.
Figure 4-3 XML Example
<?xml version=”1.0” standalone=”yes”?>
<configrecord>
<configgroup name = “serial command mode” instance = “1”>
<configitem name = “mode”>
<value>disable</value>
</configitem>
</configgroup>
</configrecord>
Figure 4-4 XML Example of Multiple Named Values
<?xml version="1.0" standalone="yes"?>
<configgroup name = "ethernet" instance = "eth0">
<configitem name = "speed">
<value>Auto</value>
</configitem>
<configitem name = "duplex">
<value>Auto</value>
</configitem>
</configgroup>

4: Configuration Using XML
PremierWave® XC Intelligent Gateway Command Reference 17
Figure 4-5 XML Example of Multiple Items
<configgroup name="ssh server">
<configitem name="host rsa keys">
<value name="public key"/>
<value name="private key"/>
</configitem>
<configitem name="host dsa keys">
<value name="public key"/>
<value name="private key"/>
</configitem>
<configitem name="delete authorized users">
<value>disable</value>
</configitem>
<configitem name="authorized user delete">
<value name="name"/>
</configitem>
<configitem name="authorized user" instance="">
<value name="password"/>
<value name="public rsa key"/>
<value name="public dsa key"/>
</configitem>
</configgroup>
Figure 4-6 XML Example with Multiple Groups
<?xml version="1.0" standalone="yes"?>
<configgroup name = "telnet">
<configitem name = "state">
<value>enable</value>
</configitem>
<configitem name = "authentication">
<value>disable</value>
</configitem>
</configgroup>
<configgroup name = "ssh">
<configitem name = "state">
<value>enable</value>
</configitem>
</configgroup>

4: Configuration Using XML
PremierWave® XC Intelligent Gateway Command Reference 18
Importing and Exporting an XML Configuration File
An XCR can be imported or exported using the following methods:
Filesystem-XCRs can be saved to the intelligent gateway file system and imported or
accessed as needed. See Best Practices on page 18 or the Filesystem Browser section in the
PremierWave XC Intelligent Gateway User Guide.
CLI-XCRs can be imported (captured) or exported (dumped) directly to a Telnet, SSH, or
serial line CLI session. Capturing an XCR can be started by pasting a valid XCR directly into
the CLI prompt. PremierWave XC intelligent gateway immediately processes the configuration
record, changing any settings specified. This can be done on any level, including the root.
Special tags in the XML allow for providing root and enable level passwords so that this can
also be done at the password prompt.
Web browser-Web Manager can be used to import and export an XCR to the intelligent
gateway file system. It can also be used to import an XCR from an external source such as
your local hard drive.
FTP-The intelligent gateway FTP server can export and import XCRs when an FTP get or put
command on the filename (pwxc.xcr for export, pwxc_import.xcr for import; both are under the
pwxc directory) is requested. On export (FTP get of pwxc.xcr), the FTP server obtains the
current XCR from the PremierWave XC device and sends it as a file. On import (FTP put of
pwxc_import.xcr), the FTP server processes the file by sending it directly to the XML engine.
In both cases the intelligent gateway filesystem is not accessed. The files pwxc.xcr and
pwxc_import.xcr are not read from or written to the file system. See FTP in the PremierWave
XC Intelligent Gateway User Guide.
Best Practices
You can import or export an entire XCR, or just a portion of it, by specifying the group name and/or
group instances. In the examples below, import and export operations are performed from the CLI
on the local filesystem and require a XCR on the local filesystem. The Web Manager provides the
same functionality.
Caution: Using Microsoft Word to edit and save an XCR will change the format of
the file and make it incompatible with PremierWave XC intelligent
gateway. This is true even if the file is saved as Plain Text (.txt) or an
XML Document (.xml). Notepad, a third party text editor, or a specialized
XML editor should be used instead.
Importing
The following syntax can be used to import configurations from a file:
xcr import <file>
xcr import <file> <groups and/or group:instances>
The first line imports all groups specified in the XML config record named in <file>. Any filename is
valid, and the file name and extension are not important.
In the second line:
Instance follows group with a colon (see the third example on the next page).
Multiple groups are separated with a comma.

4: Configuration Using XML
PremierWave® XC Intelligent Gateway Command Reference 19
Any white space requires the list of groups to be quoted.
Only the named groups get imported, even if the XCR contains additional XCR groups.
The following syntax can be used to export configurations to a file on the intelligent gateway's file
system:
xcr export <file>
xcr export <file> <groups and/or group:instances>
The same guidelines above regarding importing configurations also apply to exporting
configurations. If no groups are specified, then the export command will export all configuration
settings to the file. If instances are specified after the groups, only those group instances are
written. If no instance is specified, all instances of that group are written.
Exporting
The following example exports only the accept mode tunneling settings for line 1 to the file
"tunnel_1.xcr" on the intelligent gateway filesystem:
xcr export tunnel_1.xcr "tunnel accept:1"
The following example exports only the connectmode tunneling settings for all ports to the file
"tunnel_all.xcr" on the PremierWave XC filesystem:
xcr export tunnel_all.xcr "tunnel connect"
The following example imports only the settings for line2 from an XCR named "factory_config.xcr"
on the intelligent gateway filesystem. If "factory_config.xcr" has other configuration settings, they
are ignored:
xcr import factory_config.xcr "line:2"
The following example imports only line settings for all ports from a configuration record on the
PremierWave XC filesystem named "foobar.xcr":
xcr import foobar.xcr "line"
To import only disconnect mode tunnel settings for port 1 and all serial line tunnel settings for port
2 from an XML configuration record named "production.xcr" that contains these settings (and
possibly more), issue the following command:
xcr import production.xcr "tunnel disconnect:1"
The following example imports all tunneling settings and line settings for all serial ports from a file
named xcr_file:
xcr import xcr_file "tunnel accept, tunnel connect, tunnel
disconnect, tunnel modem, tunnel packing, tunnel serial, tunnel
start, tunnel stop, line"
The following example exports only accept mode tunneling settings on serial port 1, and line
settings on serial port 2 to a file named tunnel_config_t1_l2.xcr on the intelligent gateway
filesystem.
xcr export tunnel_config_t1_l2.xcr "tunnel accept:1, line:2"
The following example exports connect mode tunneling and line settings for all ports to the file
tunnel_config.xcr on the PremierWave XC filesystem:
xcr export tunnel_config.xcr "tunnel, line"

4: Configuration Using XML
PremierWave® XC Intelligent Gateway Command Reference 20
XML Configuration Groups
Table 4-7 lists the PremierWave XC intelligent gateway XCR groups in alphabetical order. This
table indicates the various group items, as well as some possible value names and options.
Note: Any instance of &#60 in the table may be read as "less than" and any instance of
&#62 may be read as "greater than".
Table 4-7 XCR Groups
Group Name Group Item Value Name Value Options Additional
Information
action
("Instance" attribute
is “digital input 1
state change”,
“digital input 2 state
change”, “eth0 link
state change” or
“wwan0 link state
change”)
delay
email alarm email none, email
<number> Default: none
alarm message &#60;None&#62;, ...
alarm reminder
interval &#60;None&#62;, ... Default: none
normal email none, email
<number> Default: none
normal message &#60;None&#62;, ...
normal reminder
interval &#60;None&#62;, ...
ftp put connection<number>
filename Default: data.txt
connection<number>
host
connection<number>
password Default: [email protected]
om
connection<number>
port Default: 21
connection<number>
protocol ftp, ftps Default: ftp
connection<number>
username Default: anonymous
mode sequential,
simultaneous Default: simultaneous
reminder interval &#60;None&#62;, ... Default: none