Laserworld CS-200RGY User manual

CS-200RGY
USER MANUAL
Please read this manual carefully efore use!

USER MANUAL: Laserworld CS-200RGY
Date: 01/2008
Page
2
o
11
Checking Parts
Please check i the ollowing parts are included:
1 x CS-200RGY Laser
1 x Power cable
1 x DMX cable
1 x Interlock plug
1 x User manual

USER MANUAL: Laserworld CS-200RGY
Date: 01/2008
Page
3
o
11
DANGER LASER RADIATION!
Avoid direct eye exposure!
Laser radiation can cause eye damage and/or skin damage
All protective measures or a sa e operation o this laser must be applied.
1. SAFETY INSTRUCTIONS
- I the device has been exposed to drastic temperature luctuation, do not
switch it on immediately. The arising condensation water might damage your
device. Leave the device switched o until it has reached room temperature.
1. The laser must only be used or shows. The operation is only allowed i it is
controlled by a skilled and well-trained operator.
- Never leave this device running unattended and keep it away rom children
and unauthorized persons.
2. Keep away rom heaters and other heating sources. In order to sa eguard
su icient ventilation, leave 50 cm o ree space around the device.
3. Never direct the laser beam to people or animals.
4. CAUTION LASER DIODE: Never unscrew the housing!
There are no serviceable parts inside the device. Maintenance and service
operations shall only be carried out by authorized dealers.
5. Always disconnect rom the mains when the device is not in use or be ore
cleaning it.
- HEALTH HAZARD! Never look directly into the light source, as
sensitive persons may suffer an epileptic shock!

USER MANUAL: Laserworld CS-200RGY
Date: 01/2008
Page
4
o
11
2. OPERATING DETERMINATIONS
6. The operator has to make sure that laser radiation – also re lected laser
radiation –higher than the highest allowed level is avoided by technical or
organisational measures.
7. Make sure that the used voltage is : AC 220V~240V, 50/60Hz
8. I the device is used in a lying installation, the mounting brackets and an
appropriate sa ety-rope must be ixed.
9. Laser e ects are not designed or permanent operation. Consistent operation
breaks will ensure that the device will serve you or a long time without
de ects.
10.In some countries, the operator must noti y the accidence insurance and the
authority or industrial sa ety, be ore operating a laser. For more in ormation,
contact the relevant authorities.
11.Please consider that unauthorized modi ications on the device are orbidden
due to sa ety reasons!
12.I this device will be operated in any way di erently than described in this
manual, the product may su er damages and the guarantee becomes void.
Furthermore, any other operation may lead to dangers like short-circuit,
burns, electric shock, etc.
13.When the laser is not attached to an ILDA output device (even or a short
period), switch ILDA mode o (see below), or turn the device o .

USER MANUAL: Laserworld CS-200RGY
Date: 01/2008
Page
5
o
11
Thank you or purchasing our CS-200RGY laser projector. In order to use this
product sa ely and throughtly. Please read over this manual care ully be ore any
operation,the operation must according to manual strictly to avoid any personal hurt
or products damage . Any problem exclude in this manual please contact us!.
Specification
Model Re erence# LP-209
Components
Laser projector×1
Power cable×1
DMX512 cable×1
Interlock 9pin plug×1
Laser key×2
Using voltage
AC 110V~230V，50/60Hz
Voltage o input signal -10V ~ +10V
Control Mode Auto/AUDIO/DMX/ILDA(optional)
DMX channel 12
Scanning system 20KPPS
Lasers&Power Green laser : 532nm/ 35~50mW
Red laser : 650nm/140-150mW
Operating temperature 10° ~ 40°
Dimension(mm) 280(L)×200(W)×150(H)
Weight(kg) 3
Sa ety use 250V / F2A Φ5×20mm
ATTENTION&MAINTENANCE
1. Do not disconnect the device without pro essional instruction
2. Keep surrounding dry and clean. This unit should be keep dry, do not use in
the rain or dank and dusty environment. Projector should be covered with
water-proo when operate at outside.
3. Keep surrounding temperature at15~30,Remain 10minutes or equipment
cooling a ter 2 hours continuously work, or laser expected time will be
reduced.
4. Distance between lasing aperture and projected item should not be less than 1
meter.
5. Do not turn device on/o requently to avoid broken.
6. Do not look into the laser beam directly, or view laser beam directly with
optical instruments.
7. Do not touch the device with wet hands.
8. Turn o the power be ore installation and maintenance.
9. When the laser diode became dim or broken, please contact the dealer timely.
10.To use the original package when transport again and to avoid shake.

USER MANUAL: Laserworld CS-200RGY
Date: 01/2008
Page
6
o
11
11.Maintenance should be per ormed every 15-day period, by using a sponge
which is dipped with alcohol, rather than wet cloth or other chemical liquid, to
clean the mirror.
WARNING & SAFETY
Class IIIblaser products
Power output rom 5 milliwatts to 500 milliwatts. These lasers are considered a
de inate eye hazard, particularly at the higher power levels, which WILL cause eye
damage. So these laser series models supplied with a key switch to prevent
unauthorized use, warning labels and aperture labels a ixed to the laser.
Installation sa ety
Prior to installation and operation o the laser, the paths o the beams and e ects
should be considered, particularly with respect to how they will touch the audience.
I direct audience scanning is desired then the laser energy in the e ects needs to be
considered to decide i the e ects are sa e or direct viewing.
INSTALLATION
1,Back panel instruction

USER MANUAL: Laserworld CS-200RGY
Date: 01/2008
Page
7
o
11
1: ON/OFF(Power input with inner use)
2: REMOTE---------Interlock (pin 1,2), connect to emergeny switch, or use interlock
plug
3: DIP switches, re erence to DMX Control Mode as below.
4: DMX IN/OUT
5: AUDIO-------- Tune the sensitivity o sound activation(H),MAX→high sensitivity;
MIN→low sensitivity.
6: MIC(microphone).-------- To receive sound activated signal
7: LASER--------Turn lasers ON or OFF.
8: ILDA--------DB-25 Female
Operation Mode Instruction:
A. Sound Active
Re erence to DIP switch as below to choose this mode.
B. Auto
Includes Auto mode-Auto and Auto mode-Animal,re erence to DIP switch as below.
C. DMX Control Mode
The irst part is DIP address code re erence, ollow this to choose the mode you
need.
DIP switch:
Address 1-10 Pin,(1:ON,0:OFF,x:ON or OFF)
Address code Calculate,When the mode is DMX control:
x x x x x x x x x 1
1 2 4 8 16 32 64 128 512 DMX control
when address is 1000 0000 01
this mean is 1 x 1=1, the same you must select DMXchannel 1 as the Start channel,
DMXchannel 25 as the End channel
when address is 0100 1000 01
this mean is 1 x 2 + 1 x 16=18, the same as above,select DMXchannel 18 as the
Start channel, DMXchannel 42 as the End channel.
1 ~ 10 Mode
0,0,0,0,0,0,0,0,0,0 Auto mode-Sound
1,0,0,0,0,0,0,0,0,0 Auto mode-Auto
1,1,0,0,0,0,0,0,0,0 Auto mode-Animal
0,0,1,0,0,0,0,0,0,0 Slave
x,x,x,x,x,x,x,x,x,1 DMX control

USER MANUAL: Laserworld CS-200RGY
Date: 01/2008
Page
8
o
11
DMX Channel Instruction----------12CHS single/three color
Please re er to appendix1
D. ILDA Mode
This laser projector has designed with a ILDA automatic switching eature.ILDA
mode will be active when the pin-25 emale(on the rear panel) was be connected.
All outputs are located at an ILDA-standard connector (In and Out). This can be a
25-pin D-Sub connector( emale) or a 25-pin IDC-connector(male).
The IDC-connector allows to connect a separate D-Sub connector by using a lat
cable. All outputs are symmetrical and be used in 3 di erent con igurations:
1. symmetrical signal. Outputs + and – are connected directly with the
corresponding pins o the receiving unit. For signal inversion, the 2 lines just have
to be crossed.
2. Single ended. Output – will be grounded to 0V (GND) and the outputs + and
GND have to be connectd to the inputs o the receiving unit.
3. Single ended inverted. Output + is grounded to GND and the outputs – and
GND are connected to the inputs o the receiving unit.
The maximum signal level between the scanneroutputs X and Y is 10V and the
signal level between, the coloroutputs is 5V.
All outputs can be grounded and are short circuit protected.

USER MANUAL: Laserworld CS-200RGY
Date: 01/2008
Page
9
o
11
ILDA-standard connector 25/26-pin
1 X+ Scanneroutput +
2 Y+ Scanneroutput +
3 Intens+ Intensity/Blanking +
4 Interlock A Internally connected to 17
5 Red + Coloroutput Red +
6 Green + Coloroutput Green +
7 Blue + Coloroutput Blue +
8 – 12 n.c. Not used
13 Shutter +5V *
14 X- Scanneroutput –
15 Y- Scanneroutput –
16 Intens- Intensity/Blanking –
17 Interlock B Internally connected to 4
18 Red - Coloroutput Red -
19 Green - Coloroutput Green -
20 Blue - Coloroutput Blue -
21 – 24 n.c. Not used
25 GND Signal ground
26 n.c not used (IDC-connector only)
* Note: maximum load 20mA or 5V!

USER MANUAL: Laserworld CS-200RGY
Date: 01/2008
Page
10
o
11
Appendix1
12CHS DMX INSTRUCTION
CHANNEL# DMX
Value
Function
0~49 Auto mode---Sound
50~99 Auto mode---Auto
100~149 Auto mode---Graphic
150~199 Manual mode---Sound
1) Control
mode
200~255 Manual mode---Auto
0~5 Laser o
6~35 Single color (red ~15, green ~25, yellow)
26~135 Automatic (single) color change,Speed rom 0 to27(4)
136~245 Color (original pattern) change,Speed rom 0 to 27 (4)
2) Color
246~255 Mutlicolor
3) Pattern 0~255 249 Pattern select
0~127 Manual Vertical Move
128~191 Auto Down Move,Speed rom 0 to 16 (4)
4)Vertical
moving 192~255
Auto Up Move,Speed rom 0 to 16 (4)
0~127 Manual Horizontal Move
128~191
Auto Right Move,Speed rom 0 to 16 (4)
(recommend adjust 4 channel and 13 channel )
5) Horizontal
Moving
192~255
Auto Le t Move,Speed rom 0 to 16 (4)
(recommend adjust 4 channel and 13 channel )
0~127 Manual Vertical Roll 6) Vertical
Rolling 128~255
Auto Vertical Roll,Speed from 0 to 16 (8)
0~127 Manual Horizontal 7) Horizontal
Rolling 128~255
Auto Horizontal Roll,Speed rom 0 to 16 (8)
0~127 Manual Rotation
128~191 Auto clockwise rotation,Speed rom 0 to 16 (4)
8) Rotation
192~255 Auto anti-clockwise rotation,Speed rom 0 to 16 (4)
0~85 Auto rom small to large,speed rom 0 to 18 (5)
86~170 Auto rom large to small,speed rom 0 to 18 (5)
9) Zoom
171~255 Auto Zoom by turns,speed rom 0 to 18 (5)
10) Pattern
Size 0~255 The size rom 0 to 255
11) Dot view 0~255 0 Normally,Dot view rom 1 to 10 (24)
0~127 Auto Slow draw A, speed rom 0 to 21 (6) 12) Slow
draw 128~255
Auto Slow draw B,speed rom 0 to 21 (6)
PLEASE NOTE
This device has le t our premises in absolutely per ect condition. In order to maintain
this condition and to ensure a sa e operation, it is absolutely necessary or the user
to ollow the sa ety instructions and warning notes written in this user manual.
Laserworld cannot be made liable or damages caused by incorrect installations and
unskilled operation!