LEGRAND 067697 How to use

0676 97
Characteristics
Requires you to buy and install the "... with Netatmo" connected starter pack first.
Contents
The circuit must be protected by a 10 A circuit breaker.
Connected micromodule for roller shutters
OR
Control
Module
Gateway and Home/Away wireless
switch
1
Roller shutter
motor
+ 50° C
- 5° C
35 mm
8 mm
1 x 2,5 mm2
2 x 1,5 mm2
IP 44
100-240 Vac
50/60 Hz
240 Vac max. 1 x 500 VA
100 Vac max. 1 x 270 VA
1

10
Before you start
If you plan to install connected micromodules for rolling shutters, read the following
precautions:
To order a roller shutter micromodule with one or more wireless controls, only use
the products:
Provide wireless controls for roller shutters for each additional control point.
To create a centralized order:
Use one or several wireless controls for roller shutters.
x1
or several
Wireless control for rolling shutter
(not included in this pack)

11
1Necessary safety precautions
2Install the connected micromodule for rolling shutter
Wire the connected micromodule for roller rolling shutter
N (neutral)=blue
L (live)=any except blue and gree/yellow
(earth=green/yellow
Frequency bands: 2.4 - 2.4835 GHz
Power level: < 100 mW
OFF
Switch OFF the power at main circuit
breaker
Make sure that the power
is OFF before continuing
with the installation.
1 2
N
L
L
N
This shutter micromodule is compatible
with roller shutters using mechanical
or electronic stop, controlled by an
electro-mechanical switch.
It's not compatible with radio roller
shutter controlled with a radio switch.
To check this, refers to roller shutter
instruction.

12
3 Start to congure the installed products
3 The indicator lights on the products that you have wired will turn green one by one.
1
ON
Turn the power on at the main circuit breaker
*
***
*
*Example of products not supplied
OR
> 3 s
2Press the conguration button of Modul Control or at the center
of the Hom/Away wireless switch until led ashes in green, then
stop pressing.
All leds of the wired products are green.

13
4 Prepared a wireless control
Remove the protective strip
of the wireless control of your choice.
Not included
in this pack.
2
1
Briefly press the wireless control to activate it.
The indicator light will flash green and then switch off.

14
5Pair the wireless control for rolling shutters
To pair a wireless control with one or several connected rolling shutters
A
Keep pressing the button on the wireless control and tap the micromodule for rolling
shutters you want to control 3 times with the control.
B
The two indicator lights on the product will flash blue rapidly.
C
The indicator lights on the two products will briefly turn blue, and then the light on the
wired product will turn green again and the light on the wireless control will switch off.
The pairing was successful.
Make sure that the indicator lights on the products are green and not flashing.
If not, go back to step 3.
A
BC
Multiple pairing:
You can control several rolling shutters with the same wireless control by repeating the ope-
ration for each product that you want to control.

15
To complete your installation,
briefly press the middle of the wireless general control.
All the indicator lights on the products will switch off.
If necessary, cancel the wireless control pairing
1Press the middle of the button on the wireless control until the indicator light turns
orange without ashing.
2Conrm the cancellation by briey re-pressing the middle of this button on the wireless
control and the light will turn blue and then switch o. The pairint has now been
cancelled.
You can pair the wireles control with new products by starting again from step 5.
2
1
6 Repeat steps 4and 5for all wireless controls you want to install.
7Complete the conguration
OR
< 1 s < 1 s

SIMPLIFIED EU DECLARATION OF CONFORMITY
The undersigned,
Legrand
declares that the radio-electric equipment referred to in these instructions
complies with directive 2014/53/UE.
The full text of the EU declaration of conformity is available
on the following website:
www.legrandoc.com
Safety instructions:
This product should be installed in compliance with installation rules, preferably by a qualied electrician.
Incorrect installation and/or incorrect use can lead to risk of electric shock or re.
Before carrying out the installation, read the instructions and take account of the product’s specic
mounting location.
Do not open up, dismantle, alter or modify the device except where specically required to do so by the
instructions. All Legrand products must be opened and repaired exclusively by personnel trained and
approved by Legrand. Any unauthorised opening or repair completely cancels all liabilities and the rights
to replacement and guarantees.
Use only Legrand brand accessories.
To add a connected product to your connected installation, you should
follow the instruction:
- in the Legrand Home + Control application (settings/Add a new product section)
- or consult the user manuel on legrand.fr
LEGRAND - Pro and Consumer Service - BP 30076
87002 LIMOGES CEDEX FRANCE • www.legrand.com
www.legrand.fr/reference/067697