LEGRAND Tynetec ZXT424 User manual

Doc No. FM0458 issue F Page 1
169MHz Telecare Devices
Flood Detector
__________________________________________________________________________________________________________
•Compatible with Reach at-home alarms, Advent xt warden call,
Altec Response and Touchsafe Pro Nursecall systems
•Moisture bridge sensor
•Supplied with mounting bracket
•Low battery warning
•Dimensions: 50 x 95 x 18 mm (HxWxD)
•Weight: 36 grams
•Product Code: ZXT424
Where should Flood Detectors be Located?
Flood detectors should be located on the floor below the bath, wash basin, or kitchen sink or anywhere a tap could be left
running. It should be fixed to the skirting board with the screw or self-adhesive pad provided.
Tools Required
A Pozi screwdriver will be needed if the flood detector is being screw-fixed to the skirting board.
Testing and Registering the Flood Detector
Place a damp cloth across the 2 brass studs to activate.
The flood detector must be activated when registering
onto the warden call, at-home alarm or Nursecall system.
See the following pages for how to put each of these
products into registration mode.
The range of all radio devices can be affected by the working environment - always take care during installation and
perform several test calls.
Installation
It is easier to test and learn the flood detector before fixing –see above.
When fixing; always ensure the 2 brass studs are touching the floor.
Select the best location, then fix to the skirting board with the single screw through
the hole in the right angle bracket.
If using the self-adhesive pad; select a location where the skirting board is clean and dry.
Stick the adhesive pad to the rear of right angle bracket then press the detector firmly
to the skirting board ensuring it is stuck securely.
Flood Alarms
If the flood detector signals an alarm remove it from the affected area until the carpet/flooring is thoroughly dried. Dry the flood
detector to prevent corrosion of the brass studs. Note: if the flood detector is frequently activated by water on the floor then it
may be necessary to relocate the device away from the cause of the alarm.
Battery Life
The flood detector battery is checked once a day, if the voltage falls and stays below a preset level for 7 consecutive days a low
battery alert is automatically transmitted. Once a low battery call is received the flood detector should be replaced within 7 days.
Flood detectors must be returned to Tynetec/Aidcall for battery replacement.
Detailed information on battery management for all Tynetec/Aidcall products is available - request Doc No. FM0630.
BRIDGE THE 2 BRASS
STUDS WITH A DAMP
CLOTH TO ACTIVATE
Tynetec and Aidcall are business units of Legrand Electric Ltd
Unit 10 Cowley Road, Blyth Riverside Business Park, Blyth
Northumberland, NE24 5TF. Tel: [phone] Fax: [phone]
Email: [e-mail] Web: www.tynetec.co.uk

Doc No. FM0458 issue F Page 2
Registering a Flood Detector onto a Reach at-home alarm unit
1. Put the Reach unit into radio device learn mode…
2. Activate the flood detector…
3. Exit radio device learn mode…
4. Check with the Control Centre that it is convenient to perform a test call, activate the flood detector and confirm they receive a
flood alarm call.
Deleting a Flood Detector from a Reach at-home alarm unit
Enter 1 6 7 0 using the keypad on the rear of the Reach unit –the front light will FLASH FAST GREEN and the unit will announce
“Program Mode - Ready”.
Enter # 0 4 1 and the Reach will announce “Delete Radio Device” followed by a “Beep”.
Enter the 8 digit big button ID to be deleted; after the “Beep” press #to exit.
Press the key to exit Program Mode; the unit will sound a “Double-Beep” and the front light will return to STEADY GREEN.

The 8 digit ID can be found on a label on the top of the flood detector –it will always start with 80xxxxxx
The instructions given above for the standard Reach product also applies to the Reach Plus, Reach Plus GSM
and Reach Ultra models. Refer to the instruction booklets provided with these products for more information
on programming and testing radio devices.
Place a damp cloth across the 2 brass studs on the
bottom of the flood detector and the Reach will
announce “Flood”.
“Trigger
Radio
Device”
Press and HOLD the GREEN button on the Reach unit.
When the front light FLASHES FAST GREEN release the
button and the Reach will announce “Trigger Radio Device”.
You now have 1 minute to activate the flood detector.

Press the GREEN button on the Reach unit.
The front light will return to STEADY GREEN and the Reach
is back in normal operating mode.
⚫

Doc No. FM0458 issue F Page 3
Registering a Flood Detector onto an Advent xt warden call system
1. Put the Advent xt system into radio device learn mode…
2. Activate the flood detector…
3. Exit the Advent xt system radio device learn mode…
4. Activate the flood detector and check a flood alarm call is reported on the warden call system.
Deleting a Flood Detector from an Advent xt warden call system
Press the LINE key and wait for the “Ready” prompt.
Enter 5 0 0 1 followed by the key.
Enter the flat number the flood detector is being deleted from followed by the key.
Activate the flood detector to be deleted.
Wait for the “Pendant Disabled –Enter Flat” prompt.
Press the #key and wait for the “Ready” prompt, then press the LINE key to clear the connection.
Refer to the Advent xt operator’s manual (Doc No. FM0420) provided with the warden call system for more
information on programming and testing radio devices.
Using the Manager’s DECT telephone;
Press the LINE key and wait for the “Ready” prompt.
Enter 5 0 0 0 followed by the key.
Enter the flat number the flood detector is being installed in
followed by the key.
You now have 1 minute to activate the flood detector.
“Ready”
Using the Manager’s DECT telephone;
Press the #key and wait for the “Ready” prompt.
Press the LINE key to clear the connection and the warden call system is
now back in normal operating mode.
Place a damp cloth across the 2 brass studs on the bottom
of the flood detector.
Wait for the “Enter Location Code” prompt then press 0
(no location) followed by the key.
Wait for the “Pendant Enabled –Enter Flat” prompt.
“Ready”

Doc No. FM0458 issue F Page 4
Registering a Flood Detector onto an Altec Response local carer alarm unit
1. Put the Altec Response unit into radio device learn mode…
2. Activate the flood detector…
3. Exit the Altec Response radio device learn mode…
4. Activate the flood detector and check a flood alarm is displayed on the Altec Response unit.
Deleting a Flood Detector from an Altec Response local carer alarm unit
Press ENTER to activate the wake-up display then ENTER again to display the main menu
Press ENTER to select Radio Devices 
Press the key to select Delete Device then press ENTER
The display will prompt you to “Trigger the Sensor”
Activate the flood detector to be deleted - the display will show the device type and its 8 digit ID number
If this is the device you activated press the key to select Delete then press ENTER
If it’s NOT the device you activated press the ENTER key to select Reject then try again
To exit the mode select Exit then press the ENTER key.
Refer to the Altec Response installation guide (Doc No. FM0548) provided with the portable alarm unit for
more information on programming and testing radio devices.
Place a damp cloth across the 2 brass studs on the bottom of the flood detector.
The display will show Flood and the flood detector 8 digit ID number.
Check the ID is correct, press the key to select Accept then press ENTER.
Note: if another device has been picked-up press ENTER to Reject and try again.
The display will show Flat , use the & keys to choose the dwelling type.
Press the key to select No: 000000 then press the ENTER key.
Use the & keys to select each digit of the flat number and the & keys
to move between digits then press the ENTER key.
Press key several times to select Exit then press the ENTER key.
The display will prompt you to “Trigger the Sensor”again.
Press ENTER to activate the wake-up display then ENTER again to display
the main menu.
Press ENTER to select Radio Devices 
Press ENTER to select Learn Device 
The display will prompt you to “Trigger the Sensor”.
You now have 20 seconds to activate the flood detector.
From the Learn Device menu select Exit then press ENTER.
From the Radio Devices menu select Exit then press ENTER.
The display will return to the wake-up screen and go blank after 10 seconds.
The Altec Response is now back in normal operating mode.
tynetec
tynetec

Doc No. FM0458 issue F Page 5
Registering a Flood Detector onto aTouchsafe Pro Nursecall system
1. Put the Touchsafe Pro Master Panel into Telecare registration mode; touch the screen and Logon as an Engineer or a Manager
(password required), then from the main menu page touch the Telecare button to open the screen shown below…
2. Enter the big button ID…
3. Press the Close button to exit Telecare mode and the Nursecall panel is now back in normal operating mode.
4. Activate the flood detector with a damp cloth and check a call is displayed on the Nursecall panel like this…
The screen banner is grey for a flood call (Touch the banner to display notes).
Press the Accept button on the banner to silence the alarm - this will also
notify all other panels the call is being dealt with.
The screen banner changes to purple when a call is accepted.
You must visit the appropriate Nursecall Call Point to cancel the call.
Deleting a Flood Detector from a Touchsafe Pro Nursecall system
Select the flood detector ID to be deleted from the Delete Telecare Device pull-down list box (prefixed with a “T80”).
Details of the flood detector selected will be displayed in the Room, House Code and ID boxes below.
If the details shown are correct press the Delete button.
Press the Close button to exit.
Refer to the Touchsafe Pro Display Panel user guide (Doc No. FM5505) provided with the Nursecall system for
more information.
Tynetec and Aidcall operate a policy of continuous improvement and reserve the right to change product specifications without notice.
If any variation to the details contained in this document are suspected please contact Tynetec’s customer support dept on 01670 352371.
The 8 digit ID is printed on a label on the top of the flood detector.
Note: this ID will always start with 80xxxxxx.
Touch the Add Telecare Device box then use the on-screen keypad to enter the ID.
Hint: enter a zone in the Filter box to narrow the search for the room (see below).
Select the users Call Point ID from the Room pull-down list box then press Save.
Note: this is the room unit that will be will be used to cancel the call.
Use keypad to enter
8 digit ID here
Select the relevant
Call Point ID here
Save when done
Close to exit mode
ZXT424 W64317
Ser: 09158334
ID: 80042241
EE0750 V1.07A
On-screen keypad
CALLING
CANCEL
HC 345 ID 001
Press the LIGHT GREY
button to cancel the call
MC