Lenze 8400 BaseLine C User manual

EDS84ABD302
.>3ö
Ä.>3öä
Hardware Manual
8400 0.25 ... 3.0 kW

E84A... - BaseLine C/BaseLine D
8400 frequency inverter
L-force Drives
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

0Fig. 0Tab. 0
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

Contents i
3
EDS84ABD302 EN 4.0
1 About this documentation 6..................................................
1.1 Document history 6....................................................
1.2 Conventions used 7....................................................
1.3 Notes used 8..........................................................
2 Safety instructions 9.........................................................
2.1 General safety information 9............................................
2.2 General safety and application instructions for Lenze motors 12................
2.3 Residual hazards 15.....................................................
3 Product description 16........................................................
3.1 Device features 16......................................................
3.2 Overview of the devices 17...............................................
3.2.1 Determining the device type 18...................................
3.2.2 Type code 19...................................................
4 Technical data 20............................................................
4.1 General data and operating conditions 20.................................
4.2 Rated data 24..........................................................
4.2.1 Overview 24....................................................
4.2.2 Operation at rated mains voltage 230 V 26..........................
4.2.3 Operation at rated mains voltage 400 V 29..........................
4.2.4 Operation at rated mains voltage 500 V 33..........................
4.3 Overcurrent operation 36................................................
4.3.1 Device overload for 15-s cycle 37...................................
4.3.2 Device overload for 180-s cycle 38..................................
4.4 Terminal description 39..................................................
4.4.1 Overview 39....................................................
4.5 Control terminals 40.....................................................
4.5.1 External supply voltage 24 V 40....................................
4.5.2 Analog input 41.................................................
4.5.3 Digital inputs 42................................................
4.5.4 Digital outputs 42...............................................
4.5.5 Relay output connection 42.......................................
5 Mechanical installation 43.....................................................
5.1 Important notes 43......................................................
5.2 Standard devices in the power range from 0.25 ... 3 kW 44.....................
5.2.1 Assembly in built-in technique (standard) 44........................
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

Contentsi
4EDS84ABD302 EN 4.0
6 Electrical installation 45.......................................................
6.1 Important notes 45......................................................
6.1.1 Electrical isolation 47............................................
6.1.2 Device protection 48.............................................
6.1.3 Maximum motor cable length 48..................................
6.1.4 Motor protection 48.............................................
6.1.5 Interaction with compensation equipment 48.......................
6.1.6 Safety notes for the installation according to UL or UR 49.............
6.2 Installation according to EMC (installation of a CE-typical drive system) 50.......
6.2.1 Shielding 50....................................................
6.2.2 Mains connection, DC supply 52...................................
6.2.3 Motor cables 53.................................................
6.2.4 Control cables 54................................................
6.2.5 Installation in the control cabinet 55...............................
6.2.6 Wiring outside the control cabinet 57..............................
6.2.7 Detecting and eliminating EMC interferences 59.....................
6.3 Devices in the power range 0.25 ... 2.2 kW (1/N/PE AC 230 V) 60................
6.3.1 Example circuits 60..............................................
6.3.2 Terminal assignment of the power connections 61...................
6.4 Devices in the power range from 0.37 to 3 kW (3/PE AC 400 V) 66...............
6.4.1 Example circuits 66..............................................
6.4.2 Terminal assignment of the power connections 67...................
6.5 Control terminals 72.....................................................
6.5.1 Important notes 72..............................................
6.5.2 System bus connection (CANopen) 74..............................
6.5.3 Analog input 75.................................................
6.5.4 External supply voltage 24 V 77....................................
6.5.5 Digital inputs and outputs 78.....................................
6.5.6 Relay output connection 80.......................................
6.5.7 Diagnostics 81..................................................
7 Commissioning 82...........................................................
7.1 Before switching on 82..................................................
7.2 Display elements and control panel 83.....................................
7.3 Menu structure 85......................................................
7.4 Preparing the commissioning procedure 86.................................
7.5 Test commissioning 87..................................................
7.5.1 Test commissioning with keypad control 88.........................
7.5.2 Test commissioning with terminal control 90........................
7.6 Messages 92...........................................................
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

Contents i
5
EDS84ABD302 EN 4.0
8Brakingoperation 93.........................................................
8.1 Braking operation without additional measures 93...........................
8.2 Braking operation with external brake module 94...........................
8.3 Braking operation with external brake resistor 95............................
8.3.1 Operation at rated mains voltage 400 V 96..........................
8.3.2 Operation at rated mains voltage 500 V 97..........................
8.3.3 Selection of the brake resistors 98..................................
8.3.4 Rating for Lenze brake resistors 99.................................
8.3.5 Wiring of brake resistor 100........................................
8.4 Controlling the brake 102.................................................
8.4.1 Introduction 102.................................................
8.4.2 Rated data 103..................................................
8.4.3 Wiring 104......................................................
9 Accessories (overview) 105.....................................................
9.1 Overview 105............................................................
9.2 Mains chokes 106........................................................
9.3 External brake resistors 107...............................................
9.4 Memory modules 108.....................................................
9.5 Keypad 110.............................................................
10 Appendix 111................................................................
10.1 Total index 111..........................................................
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

About this documentation
Document history
1

6EDS84ABD302 EN 4.0
1 About this documentation
Contents
This Hardware Manual informs you how to use the BaseLine C and BaseLine D version of
the 8400 controller series as directed.
Validity
The information in this Hardware Manual applies to the 8400 BaseLine C and BaseLine D
inverters with the following nameplate data:
Type Type designation From hardware version From software version
8400 BaseLine C E84AVBCxxxxxxX0 VA 03.00
8400 BaseLine D E84AVBDxxxxxxX0 VA 03.00
8400 BaseLine D with
digital output ”DO1”
E84AVBDxxxxxxX11A 02.01
8400 BaseLine D without
digital output ”DO1”
E84AVBDxxxxxxX01A 01.00
Material number Version Description
13251886 1.1 06/2008 TD03 First edition
13260428 2.0 07/2008 TD03 Complete revision
13277182 3.0 02/2009 TD03 New edition due to company reorganisation
Corrections in Chapter ”Technical Data” and
”Electrical Installation”
.>3ö 4.0 03/2009 TD03 Corrections in Chapter ”Mechanical Installation”
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

About this documentation
Conventions used
1
7
EDS84ABD302 EN 4.0
1.2 Conventions used
This documentation uses the following conventions to distinguish between different
types of information:
Type of information Writing Examples/notes
Notation of numbers
Decimal separator Point The decimal point is always used.
For example: 1234.56
Warnings
UL warnings Are only given in English.
UR warnings 
Text font style
Program name »« Lenze software
For example: »Engineer«
Symbols
Cross-reference  Refers to additional information. For
example 16 = see page 16.
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

About this documentation
Notes used
1

8EDS84ABD302 EN 4.0
1.3 Notes used
The following pictographs and signal words are used in this documentation to indicate
dangers and important information:
Safety instructions
Structure of safety instructions:
Danger!
(characterises the type and severity of danger)
Note
(describes the danger and gives information about how to prevent dangerous
situations)
Pictograph and signal word Meaning
Danger!
Danger of personal injury through dangerous electrical voltage.
Reference to an imminent danger that may result in death or
serious personal injury if the corresponding measures are not
taken.
Danger!
Danger of personal injury through a general source of danger.
Reference to an imminent danger that may result in death or
serious personal injury if the corresponding measures are not
taken.
Stop!
Danger of property damage.
Reference to a possible danger that may result in property
damage if the corresponding measures are not taken.
Application notes
Pictograph and signal word Meaning
Note! Important note to ensure troublefree operation
Tip! Useful tip for simple handling
Reference to another documentation
Special safety instructions and application notes for UL and UR
Pictograph and signal word Meaning
Warnings!
Safety or application note for the operation of a UL-approved
device in UL-approved systems.
Possibly the drive system is not operated in compliance with UL
if the corresponding measures are not taken.
Warnings!
Safety or application note for the operation of a UR-approved
device in UL-approved systems.
Possibly the drive system is not operated in compliance with UL
if the corresponding measures are not taken.
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

Safety instructions
General safety information
2
9
EDS84ABD302 EN 4.0
2 Safety instructions
2.1 General safety information
Foryourpersonalsafety
Disregarding the following safety measures can lead to severe injury to persons and
damage to material:
ƒOnly use the product as directed.
ƒNevercommissiontheproductintheeventofvisibledamage.
ƒNever commission the product before assembly has been completed.
ƒDo not carry out any technical changes on the product.
ƒOnly use the accessories approved for the product.
ƒOnly use original spare parts from Lenze.
ƒObserve all regulations for the prevention of accidents, directives and laws
applicable on site.
ƒTransport, installation, commissioning and maintenance work must only be carried
out by qualified personnel.
– Observe IEC 364 and CENELEC HD 384 or DIN VDE 0100 and IEC report 664 or
DIN VDE 0110 and all national regulations for the prevention of accidents.
– According to this basic safety information, qualified, skilled personnel are persons
who are familiar with the assembly, installation, commissioning, and operation of
the product and who have the qualifications necessary for their occupation.
ƒObserve all specifications in this documentation.
– This is the condition for safe and trouble-free operation and the achievement of
the specified product features.
– The procedural notes and circuit details described in this documentation are only
proposals. It’s up to the user to check whether they can be transferred to the
particular applications. AC Technology Corporation does not accept any liability for
the suitability of the procedures and circuit proposals described.
ƒDepending on their degree of protection, some parts of the Lenze controllers
(frequency inverters, servo inverters, DC speed controllers) and their accessory
components can be live, moving and rotating during operation. Surfaces can be hot.
– Non-authorised removal of the required cover, inappropriate use, incorrect
installation or operation, creates the risk of severe injury to persons or damage to
material assets.
– For more information, please see the documentation.
ƒHigh amounts of energy are produced in the controller. Therefore it is required to
wear personal protective equipment (body protection, headgear, eye protection, ear
protection, hand guard).
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

Safety instructions
General safety information
2

10 EDS84ABD302 EN 4.0
Application as directed
Controllers are components which are designed for installation in electrical systems or
machines. They are not to be used as domestic appliances, but only for industrial purposes
according to EN 61000-3-2.
When controllers are installed into machines, commissioning (i.e. starting of the operation
as directed) is prohibited until it is proven that the machine complies with the regulations
of the EC Directive 98/37/EC (Machinery Directive); EN 60204 must be observed.
Commissioning (i.e. starting of the operation as directed) is only allowed when there is
compliance with the EMC Directive (2004/108/EC).
The controllers meet the requirements of the Low-Voltage Directive 2006/95/EC. The
harmonised standard EN 61800-5-1 applies to the controllers.
The technical data and supply conditions can be obtained from the nameplate and the
documentation. They must be strictly observed.
Warning: Controllers are products which can be installed in drive systems of category C2
according to EN 61800-3. These products can cause radio interferences in residential areas.
In this case, special measures can be necessary.
Transport, storage
Please observe the notes on transport, storage, and appropriate handling.
Observe the climatic conditions according to the technical data.
Installation
The controllers must be installed and cooled according to the instructions given in the
corresponding documentation.
The ambient air must not exceed degree of pollution 2 according to EN 61800-5-1.
Ensure proper handling and avoid excessive mechanical stress. Do not bend any
components and do not change any insulation distances during transport or handling. Do
not touch any electronic components and contacts.
Controllers contain electrostatic sensitive devices which can easily be damaged by
inappropriate handling. Do not damage or destroy any electrical components since this
might endanger your health!
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

Safety instructions
General safety information
2
11
EDS84ABD302 EN 4.0
Electrical connection
When working on live controllers, observe the applicable national regulations for the
prevention of accidents (e.g. VBG 4).
The electrical installation must be carried out according to the appropriate regulations
(e.g. cable cross-sections, fuses, PE connection). Additional information can be obtained
from the documentation.
This documentation contains information on installation in compliance with EMC
(shielding, earthing, filter, and cables). These notes must also be observed for CE-marked
controllers. The manufacturer of the system is responsible for compliance with the limit
values demanded by EMC legislation. The controllers must be installed in housings (e.g.
control cabinets) to meet the limit values for radio interferences valid at the site of
installation. The housings must enable an EMC-compliant installation. Observe in
particular that e.g. the control cabinet doors have a circumferential metal connection to
the housing. Reduce housing openings and cutouts to a minimum.
Lenze controllers can cause a DC current in the PE conductor. If a residual current device
(RCD) is used for protection in the event of direct or indirect contact, a residual current
device (RCD) of type B must be used on the supply side of the controller in case of a
three-phase controller supply. Otherwise, a different protective measure must be taken,
e.g. separation from the environment through double or reinforced insulation or
separation from the supply system by means of a transformer.
Operation
If necessary, systems including controllers must be equipped with additional monitoring
and protection devices according to the valid safety regulations (e.g. law on technical
equipment, regulations for the prevention of accidents). The controllers can be adapted to
your application. Please observe the corresponding information given in the
documentation.
After the controller has been disconnected from the supply voltage, all live components
and power connections must not be touched immediately because capacitors can still be
charged. Please observe the corresponding stickers on the controller.
All protection covers and doors must be shut during operation.
Notes for UL-approved systems with integrated controllers: UL warnings are notes that
only apply to UL systems. The documentation contains special UL notes.
Maintenance and servicing
The controllers do not require any maintenance if the prescribed operating conditions are
observed.
Disposal
Recycle metal and plastic materials. Ensure professional disposal of assembled PCBs.
The product-specific safety and applicationnotesgivenintheseinstructionsmustbe
observed!
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

Safety instructions
General safety and application instructions for Lenze motors
2

12 EDS84ABD302 EN 4.0
2.2 General safety and application instructions for Lenze motors
(According to: Low-Voltage Directive 2006/95/EC)
General
Low-voltage machines have hazardous live and rotating parts and possibly also hot
surfaces.
Synchronous machines induce voltages at open terminals during operation.
All operations concerning transport, connections, commissioning and maintenance must
be carried out by qualified, skilled personnel (EN 50110-1 (VDE 0105-100) and IEC 60364
must be observed). Inappropriate use creates the risk of severe injury to persons and
damage to material assets.
Low-voltage machines may only be operated under the conditions that are indicated in the
section ”Application as directed”.
The conditions at the place of installation must comply with the data given on the
nameplate and in the documentation.
Application as directed
Low-voltage machines are intended for commercial installations. They comply with the
harmonised standards of the series EN 60034 (VDE 0530). Their use in potentially
explosive atmospheres is prohibited unless they are expressly intended for such use
(follow additional instructions).
Low-voltage machines are components for installation into machines as defined in the
Machinery Directive 98/37/EC. Commissioning is prohibited until the conformity of the
end product with this directive has been established (follow i. a. EN 60204-1).
Low-voltage machines with IP23 protection or less are only intended for outdoor use when
applying special protective features.
The integrated brakes must not be used as safety brakes. It cannot be ruled out that factors
which cannot be influenced, such as oil ingress due to a defective A-side shaft seal, cause
a brake torque reduction.
Transport, storage
Damage must be reported immediately to the forwarder upon receipt; if required,
commissioning must be excluded. Tighten screwed-in ring bolts before transport. They are
designed for the weight of the low-voltage machines, do not apply extra loads. If
necessary, use suitable and adequately dimensioned means of transport (e. g. rope
guides).
Remove transport locking devices before commissioning. Reuse them for further
transport. When storing low-voltage machines, ensure a dry, dust-free and low-vibration
(veff ≤0.2 mm/s) environment (bearing damage while being stored).
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

Safety instructions
General safety and application instructions for Lenze motors
2
13
EDS84ABD302 EN 4.0
Installation
Ensure an even surface, solid foot/flange mounting and exact alignment if a direct clutch
is connected. Avoid resonances with the rotational frequency and double mains frequency
which may be caused by the assembly. Turn rotor by hand, listen for unusual slipping
noises. Check the direction of rotation when the clutch is not active (observe section
”Electrical connection”).
Use appropriate means to mount or remove belt pulleys and clutches (heating) and cover
them with a touch guard. Avoid impermissible belt tensions.
The machines are half-key balanced. The clutch must be half-key balanced, too. The visible
jutting out part of the key must be removed.
If required, provide pipe connections. Designs with shaft end at bottom must be protected
with a cover which prevents the ingress of foreign particles into the fan. Free circulation of
the cooling air must be ensured. The exhaust air - also the exhaust air of other machines
next to the drive system - must not be taken in immediately.
Electrical connection
All operations must only be carried out by qualified and skilled personnel on the
low-voltage machine at standstill and deenergised and provided with a safe guard to
prevent an unintentional restart.This also applies to auxiliary circuits (e. g. brake, encoder,
blower).
Check safe isolation from supply!
If the tolerances specified in EN 60034-1; IEC 34 (VDE 0530-1) - voltage ±5 %, frequency
±2 %, waveform, symmetry - are exceeded, more heat will be generated and the
electromagnetic compatibility will be affected.
Observe the data on the nameplate, operating notes, and the connection diagram in the
terminal box.
The connection must ensure a continuous and safe electrical supply (no loose wire ends);
use appropriate cable terminals. The connection to the PE conductor must be safe. The
plug-in connectors must be bolted tightly (to stop).
The clearances between blank, live parts and to earth must not fall below 8 mm at
Ur≤550 V, 10 mm at Ur≤725 V, 14 mm at Ur≤1000 V.
The terminal box must be free of foreign particles, dirt and moisture. All unused cable
entries and the box itself must be sealed against dust and water.
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

Safety instructions
General safety and application instructions for Lenze motors
2

14 EDS84ABD302 EN 4.0
Commissioning and operation
Before commissioning after longer storage periods, measure insulation resistance. In the
case of values ≤1kΩper volt of rated voltage, dry winding.
For trial run without output elements, lock the featherkey. Do not deactivate the
protective devices, not even in a trial run.
Check the correct operation of the brake before commissioning low-voltage machines
with brakes.
Integrated thermal detectors do not provide full protection for the machine. If necessary,
limit the maximum current. Parameterise the controller so that the motor will be switched
off with I > Irafter a few seconds of operation, especially at the risk of blocking.
Vibrationalseveritiesveff ≤3.5 mm/s(Pr≤15 kW)or4.5 mm/s(Pr> 15 kW)areacceptableif
the clutch is activated.
If deviations from normal operation occur, e.g. increased temperatures, noises, vibrations,
find the cause and, if required, contact the manufacturer. In case of doubt, switch off the
low-voltage machine.
If the machine is exposed to dirt, clean the air paths regularly.
Shaft sealing rings and roller bearings have a limited service life.
Regrease bearings with relubricating devices while the low-voltage machine is running.
Only use the grease recommended by the manufacturer. If the grease drain holes are
sealed with a plug, (IP54 drive end; IP23 drive and non-drive end), remove plug before
commissioning. Seal bore holes with grease. Replace prelubricated bearings (2Z bearing)
after approx. 10,000 h - 20,000 h, at the latest however after 3 - 4 years.
The product-specific safety and applicationnotesgivenintheseinstructionsmustbe
observed!
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

Safety instructions
Residual hazards
2
15
EDS84ABD302 EN 4.0
2.3 Residual hazards
Protection of persons
ƒBefore working on the controller, check if no voltage is applied to the power
terminals because
– depending on the device - the power terminals L1, L2/N, L3, U, V, W, +UG, - UG and
RB remain live for at least 3 minutes after disconnecting the mains.
– the power terminals L1, L2/N, L3; U, V, W, +UG, - UG and RB remain live when the
motor is stopped.
Device protection
ƒConnect/disconnect all pluggable terminals only in deenergised condition!
ƒDetach the controllers from the installation, e.g. from the rear panel of the control
cabinet, only in deenergised condition!
Motor protection
ƒDepending on the controller settings, the connected motor can be overheated by:
– For instance, longer DC-braking operations.
– Longer operation of self-ventilated motors at low speed.
Protection of the machine/system
ƒDrives can reach dangerous overspeeds (e.g. setting of high output frequencies in
connection with motors and machines unsuitable for such conditions):
– The controllers do not offer any protection against such operating conditions. Use
additional components for this purpose.
Parameter set transfer
ƒDuring the parameter set transfer, control terminals of the controllers can adopt
undefined states!
– Therefore it is required to disable the terminal X4 (digital input signals) before the
transfer starts. This ensures that the controller is inhibited and all control
terminals have the firmly defined ”LOW” status.
ƒSwitch contactors in the motor cable only if the controller is inhibited.
When switching contactors in the motor cable while the controller is enabled, you can
activate monitoring functions of the controller. If no monitoring function is activated,
switching is permissible.
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

Product description
Device features
3

16 EDS84ABD302 EN 4.0
3 Product description
3.1 Device features
Features
Version
BaseLine D BaseLine C
Power range: 250 W to 3.0 kW 9 9
Integrated interference suppression according to
EN 61800-3 9 9
Dynamic brake transistor integrated in devices
with 400 V mains connection 9 9
Integrated shield terminal for safe installation of
the control cables 9 9
Identical connection system for the control cables
in the entire power range 9 9
System bus connection (CANopen) -9
Memory module for quick commissioning and
easy service 9 9
Interface for diagnostics and parameter settings,
also during operation 9 9
Automatic motor identification for optimum
operational performance 9 9
I2t motor monitoring 9 9
Flying restart circuit for quick and jerk-free flying
restart on the motor 9 9
DC-current braking function 9 9
Freely configurable user menu 9 9
Operating modes:
– VFCplus: V/F open loop, linear and
square-law
– SLVC: Sensorless vector control (speed)
9 9
S ramps for jerk-free acceleration and
deceleration 9 9
As option, DC bus terminal:
zto connect devices operating at 230 V to:
– an external brake module and/or
–aDCbussystemor
– DC supply (only with devices in the power
range 0.25 ... 1.5 kW)
zto connect devices operating at 400 V to:
– an external brake resistor and/or
– a DC source or a DC bus system, or
– DC supply (with devices in the power range
0.37 ... 3 kW)
9 9
Note!
When the device is operated from a DC source:
ƒthe internal RFI filter is not active.
ƒthedeviceisnotULrated.
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

Product description
Overview of the devices
3
17
EDS84ABD302 EN 4.0
3.2 Overview of the devices
BaseLine D version BaseLine C version
8400BLD020 8400BLD020
Fig. 3-1 BaseLine version, devices in the power range from 0.25 to 3 kW
Pos. Description Information
230 V 400 V
EPM - Slot for memory module 108
Sticker with warning 43
X1 System bus connection (CANopen) 74
X4
Analog input 75
10-V reference voltage
Digital inputs
78
Controller enable
Digital output
X6 Diagnostics 81
X13 Terminal for I/O shields -
X100 Terminal for mains voltage 62 68
X105 Motor terminal 65 70
X109 DC bus terminal ( optional, can be ordered as a separate item) 64 69
PE conductor -
Integrated keypad 83
Icon Description
Long discharge time: All power terminals remain live for a few minutes after mains
disconnection! The duration is given under the warning symbol on the device.
High leakage current: Carry out fixed installation and PE connection according to EN 61800-5-1!
Electrostatic sensitive devices:Beforeworkingonthedevice,thepersonnelmustbefreeof
electrostatic charge!
Hot surface: Risk of burns! Hot surfaces should not be touched without wearing protective
gloves.
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

Product description
Overview of the devices
Determining the device type
3

18 EDS84ABD302 EN 4.0
3.2.1 Determining the device type
The type data used in this manual refer to the nameplate cwhich is placed at the front of
the controller and to the nameplate dplacedonthesideofthecontroller(Fig.3-2).
8400
1234567890
L
Q
BaseLine D
K
Type:
ID No:
Output:
Input:
S/N:
HW/SW:


84BDGG100 8400BLD020
Fig. 3-2 Placement of the nameplates
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

Product description
Overview of the devices
Type code
3
19
EDS84ABD302 EN 4.0
3.2.2 Type code
E84 A V xx xxxx x x X x
Product range
8400 inverter drives
Generation
A = 1st generation
Inverter type
V = vector-controlled inverter
Version
BC = BaseLine C
BD = BaseLine D
Mounting type
E=IP20
D = push-through technique (thermal separation)
C = cold-plate technique
Power e.g.
251=25x10
1W = 0.25 kW
222=22x10
2W=2.2kW
Voltage class
2 = 230/240 V 1/N/PE AC (0.25 ... 2.2 kW)
4 = 400/500 V 3/PE AC (0.37 ... 3.0 kW)
Ambient conditions
S=standard
Safety engineering
X = no safety function
0 = without digital output ”DO1”
1 = with digital output ”DO1”
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

Technical data
General data and operating conditions
4

20 EDS84ABD302 EN 4.0
4 Technical data
4.1 General data and operating conditions
Conformity and approval
Conformity
CE 2006/95/EG Low-Voltage Directive
Approval
UL UL 508C Devices in the power range from 0.25 to 3 kW:
Industrial Control Equipment (IND.CONT.EQ), 5D81, File No.
E170350
Protection of persons and devices
Enclosure EN 60529 IP 20 in ready-for-use mounted
state
Insulation resistance EN 61800-5-1 Overvoltage category III
above 2000 m amsl: overvoltage category II
Insulation of control
circuits
EN 61800-5-1 Safe mains isolation by double/reinforced insulation. For
phase to ground (Earth) voltage < 300 VAC
Short-circuit strength EN 61800-5-1 Motor connection: limited, controller is inhibited, error
acknowledgement is required
Control terminals: full
Protective measures
against
zShort circuit
zEarth fault
zOvervoltage
zMotor stalling
zMotor overtemperature
(thermal contact, I2t monitoring)
Leakage current EN 61800-5-1 > 3.5 mA AC, > 10 mA DC Observe the regulations
and safety instructions!
Cyclic mains switching Cyclic mains switching at intervals of 3 min is permissible. If
the mains are exceptionally switched three times in one
minute, a pause of 9 min must follow.
Starting current ≤IN
Supply conditions
AC mains operation Direct connection
Power systems
TT zFor central grounded systems operation is permitted
without restrictions.
zFor corner grounded 400/500 V systems operation is
possible, but reinforced insulation to control circuits is
compromised.
TN
DC-bus operation Direct connection is possible with E84AVBxxxxx4 devices
Note: When the device is operated from a DC source, the
internal RFI filter is not active and the device is not UL rated.
Motors EN 60034 Only use motors suitable for inverter operation. Insulation
resistance:
min. û ≥1.5 kV, min. du/dt ≥5kV/μs
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]