LesMills SMARTBAR Installation guide

ASSEMBLY INSTRUCTION MANUAL
STORAGE RACK

2
STORAGE RACK
RACK ASSEMBLY 3
ACCESSORY: LOCKING UNIT ASSEMBLY 8
LES MILLS SMARTBAR RACK: SIZE AND CAPACITY 10
ACCESSORY: END CAP STICKERS 11
The latest SMARTBAR™ is the industry’s benchmark
for effectiveness in fitness. At the cutting edge of
innovation and design, SMARTBAR is engineered for
workouts that work and solves problems that traditional
barbells never knew they had. Enhancing form, results
and enjoyment for your members, SMARTBAR is the
ultimate in fitness equipment.

3
STORAGE RACK
ITEM PART QUANTITY
1 Spine Tube 1
2 Rear Base Tube 1
3 Front Base Tube 1
4 Hanger Tube (Centre) 4
5 Hanger Tube (Left) 3
6 Hanger Tube (Right) 3
7 Bar Hanger Tube (Left) 1
8 Bar Hanger Tube (Right) 1
9 Carriage Bolt (M8/115mm) 2
10 Carriage Bolt (M8/62mm) 38
11 Washer (M8/19mm/1.5mm) 26
12 Curve Washer (M8/19mm/1.5mm) 34
13 Nylon Nut (M8/8mm) 40
PARTS LIST
Spine Tube
Front Base Tube
Bar Hanger Tube (Right)
Bar Hanger Tube (Left)
Rear Base Tube
Hanger Tube (Left)
Hanger Tube (Right)
Hanger Tube (Centre)

4
STORAGE RACK
INSTRUCTIONS
1. Remove all components from the packaging and
check against the parts list on previous page.
You will need a 5mm Allen key and a 13mm spanner.
It’s important not to tighten the fixings fully until
assembly is complete.
2. Attach Rear Base Tube (2) to the Spine Tube (1), and
fasten with x4 Carriage Bolts (10), x4 washer (11) and
x4 Nylon Nut (13).
Spine Tube
Rear Base Tube

5
STORAGE RACK
INSTRUCTIONS
3. Attach Front Base Tube (3) to the Spine Tube (1),
and fasten with x4 Carriage Bolts (10), x8 washer (11)
and x4 Nylon Nut (13).
Spine Tube
Front Base Tube

6
STORAGE RACK
INSTRUCTIONS
4. Attach x3 Hanger Tube (Left) (5) and x3 Hanger
Tube (Right) (6) to the Spine Tube (1), and fasten
with x12 Carriage Bolts (10), x24 Curve Washer (12)
and x12 Nylon Nut (13).
5. Attach Bar Hanger Tube (Left) (7) and Bar Hanger
Tube (Right) (8) to the Spine Tube (1), and fasten
with x4 Carriage Bolts (10), x8 Curve Washer (12)
and x4 Nylon Nut (13).
Bar Hanger Tube (Right)
Bar Hanger Tube (Left)
Spine Tube
Hanger Tube (Left)
Hanger Tube (Right)

7
STORAGE RACK
INSTRUCTIONS
6. Attach x4 Hanger Tube (Centre) (4) to the Spine Tube
(1), and fasten with x2 Carriage Bolt (9), x14 Carriage
Bolt (10), x2 Curve Washer (12), x14 Washer (11) and
x16 Nylon Bolt (13).
7. Once all of the fixings are fully tightened the rack
can be placed in position and is ready for use.
Spine Tube
Hanger Tube (Centre)

ACCESSORY:
LOCKING UNIT ASSEMBLY
STORAGE RACK
Lock not included.
To be supplied by purchaser.
8

9
STORAGE RACK
INSTRUCTIONS
Feed each of the cables through Hanger Tubes as
shown in the diagram. Ensure that the eyelet is at the
bottom of the rack, and the stopper at the top. Attach
a padlock (not included) to secure the weights to the
rack. Locking unit can be stored behind the rack when
not in use.

10
STORAGE RACK
Safe weight fully loaded is 800 kgs, and a projected area of that weight is 0.6m2(square metres). It is the responsibility of the purchaser to ensure the building floor is suitably
complied for that loading (especially if multiple racks are stacked next to each other).
SIZE AND CAPACITY
1kg, 2.5kg (or 3.7kg if 1kg beside)
1kg or 2.5kg
1kg
1kg, 2.5kg, 3.7kg, 5kg or 7.5kg
1kg, 2.5kg, 3.7kg, 5kg, 7.5kg or 10kg
2 x 3 Bars
(Both Sides)
1kg
1kg or 2.5kg
1kg, 2.5kg, 3.7kg or 5kg
1.27m
0.71m
1.25m