Let's Go Aero HideOut Package H01564 User manual

For More Information & Accessories,
Visit our Website - www.LetsGoAero.com
Contact Us at 877-474-2376 or 719-630-3800 | Email [email protected] HOMANUAL 052517
HideOut Package™
Covered Bicycle Storage and Transport Accessory System
Part No. H01564
PARTS LIST
QTY. DESCRIPTION
A1 V-BASE
B2 HORIZONTAL LEG
C4 LOCK NUT
D4 HEX BOLT
E2 WIRE LOCK PIN
F 4 SMALL COTTER PIN
G2 WING
H 4 UPPER WHEEL CRADLE
J 4 LOWER WHEEL CRADLE
K 8 RUBBER STRAPS
L4 FOAM CUSHIONS
M2 CAM BUCKLE STRAP
1/2” (13mm) WRENCH
REQUIRED TOOLS:
J
F
E
D
A
B
H
K
G
L
M
C

STEP 2
STEP 1
Attach Adjustable Rubber Straps [K] to the
Upper Wheel Cradles [H] and Lower Wheel
Cradles [J] With the hammerhead end
facing away Peg. [DETAIL 2]
To attach Cradle Assembly [H] to
Wing [G], remove Small Cotter Pin [F], insert
through hole, and reattach Small Cotter Pin
[F] as shown in [DETAIL 3].
NOTE: Foam Cushion [L] position is not
xed. You can Cushions on Wing [G] to
expose additional holes.
Where you choose to attach each cradle
assembly will depend on the size and shape
of the bicycle(s) to be transported. Attach one Upper Cradle assembly [H] to
each side of each Wing [K] (two cradle assemblies per wing).
Loosen and slip two Lower Wheel Cradles [J] onto the Wing [G] from below
the Foam Cushions [L] with each Peg matching the direction of the Upper
Cradle Assemblies [H] as Shown [DETAIL 4].
WARNING:
ALWAYS MAKE SURE EACH
CRADLE ASSEMBLY IS HELD IN
PLACE WITH A SMALL COTTER PIN
[F] AS SHOWN IN DETAIL 3.
DETAIL 1
Connect the V-Base [A] to the
Horizontal Legs using 13 mm Hex
Bolts [D] and 13 mm Lock Nuts [C]
as shown [Detail 1].
A
K
H
C
D
DETAIL 2 DETAIL 3
KK
G
J
H
F
F
L
DETAIL 4
J
G
H

STEP 3
Install Wing [G] onto V-Base [A]
using Wire Lock Pin [E].
Open wire lock pin [E] as shown in
DETAIL 7. Insert wire lock pin [E]
through the interior hole at the end
of the Wing [G] and out the exterior
side of the carrier. (You may need
to slide Wing [G] up slightly to align
the holes). Close Wire Lock Pin [E]
by positioning the loop end of the
wire over the pin and allowing it to
spring back against the Wing [G]
as shown in DETAIL 7.
Install the remaining Wing [G]
using the remaining Wire Lock Pin
[E].
D
A
G
E
E
E
DETAIL 5 DETAIL 6
DETAIL 7
ONE YEAR LIMITED WARRANTY
Let’s Go Aero warrants this product to be free from defect in material and workmanship for one year (retain your sales re-
ceipt for your records). Any product or part thereof found to be defective within that period will be replaced without charge
provided that: (1) the product was not misused; (2) no alterations or modications were made; (3) its failure was not a
result of normal wear expected in the use of the product; (4) the product or part is delivered, freight prepaid, to Let’s Go
Aero. Manufacturers only obligation shall be to replace such products or parts proved to be defective. A Return Merchan-
dise Authorization is required prior to return. Please contact Let’s Go Aero toll-free, at 877-464-2376 or 719-630-3800, or
via email to [email protected] to get an RMA number. This warranty terminates if a purchaser transfers the product
to any other person. No warranty is given for LGA products purchased outside of the United States and Canada.
To register your product, visit the Let’s Go Aero website at www.LetsGoAero.com
For assistance with this product, please contact Let’s Go Aero:
4474 Barnes Rd, Colorado Springs, CO 80917
Phone: [phone] or 719-630-3800
Email: [email protected]
To learn more about our line of bicycle carriers for vehicle, home storage, and accessory options for carrying fat bikes,
snowboards/skis, and more, be sure to visit our website: www.LetsGoAero.com
U.S. Patent No: D717716; D717717; D684917; 8,889,456; D722289; Patents Pending
WARRANTY STATEMENT
For More Information & Accessories,
Visit our Website - www.LetsGoAero.com
Contact Us at 877-474-2376 or 719-630-3800 | Email [email protected]
Copyright © 2017 Lets Go Aero Inc.

CARRIER INSTALLATION [CARGO RACK NOT INCLUDED]
STEP 1:
Install Foam Cushions [L] on
ends of Horizontal Legs [B]
as shown. [DETAIL 8 & 9]
STEP 2:
Center and place the BikeTree inside the Carrier with
the Horizontal Legs [B] running perpendicular to the
length of the carrier. [DETAIL 10 & 11]
STEP 3:
Remove the End Cap and the highest Upper
Wheel Cradle [H] located at the top of each
Wing [G]. On the inside of the Wing, slip the
looped Connection End of the Cam Buckle
Strap [M] around the Wheel Cradle and
reconnect the Cradle with Cotter Pin [F].
Reinstall End Cap over Cam Buckle Strap
[M]. Complete for both Wings. [DETAIL 12 &
13]
STEP 4:
Connect the S-Hook End of the Cam Buckle
Strap [M] to the Carrier’s provided tie down
position with the S-Hook facing away form
the carrier. Using the Slack Side, fully tighten
Cam Buckle Strap [M] evenly on both sides
to remove shifting. [DETAIL 14 & 15]
PRESS
Connection Side
Slack Side
M
S-HOOK CONNECTION MUST ALWAYS
FACE THE EXTERIOR OF THE CARRIER AS
SHOWN. [DETAIL 14]
FAILURE TO USE THE CONNECTION SIDE OF THE CAM BUCKLE STRAP [M] WHEN SECURING THE WINGS TO THE
CARRIER MAY RESULT IN LOSS OR DAMAGE PRODUCTS AND/OR PERSONAL INJURY
WARNING:
WARNING:
L
M
G
B
L
DETAIL 8
DETAIL 10
DETAIL 12
DETAIL 14
DETAIL 11
DETAIL 13
DETAIL 15
DETAIL 9
H
F

ATTACHMENT OF BICYCLES
Reffer to STEP 2 for proper Cradle and
Wing Assembly.
Lift the bicycle and hang it on the Upper
Wheel Cradles [H] with the drive-train
of the bicycle facing away from the rack
for a closer t. Secure each Wheel to
Upper Cradles with the top side of the
tire centered on the cradle as shown
[DETAILS 16].
Loosen and adjust the Lower Wheel
Cradles [J] until they are ush and resting
against the bottom of the tire [DETAIL 17].
[Removing the Wing [G] and rearranging
the Upper and Lower Wheel Cradles may
be necessary depending on your bicycles
size and style.] Once the Cradles have
been t to size, stretch the Adjustable
Rubber Straps [K] over the tire and
reconnect to the hole position that is one hole tighter than necessary with the wheel sandwiched at the end of the Cradle
Peg away from the Wing [G] [DETAIL 18].
Note: Bike Tire can be adjusted in and out to remove contact with the BikeTree Rack. The Foam Cushions [L] should be
positioned as necessary for added protection to the nish of the bicycle.
To attach a second bicycle follow the same procedure using the two remaining Upper and Lower Wheel Cradles attached
to the back side of the Wings. Position the second bicycle with the handlebars towards the back of the rst bicycle.
BICYCLE
WHEEL
BICYCLE
WHEEL
IMPORTANT FOR SAFETY! AFTER ATTACHING BIKETREE
AND BICYCLE(S), BUT BEFORE DRIVING THE VEHICLE,
DOUBLE CHECK ALL POINTS OF ATTACHMENT TO BE SURE
THAT THEY ARE TIGHT AND SECURE!
WARNING:
K
K
K
J
H
DETAIL 16
DETAIL 17 DETAIL 18
H

Assembly and Installation:
Unfold your BossHog HideOut Cover and drape over top of your BossHog Carrier, assembled BikeTree, and
customer supplied bicycles. Fit the thick Waist-Band of the HideOut Cover snuggly over the corners of the
carrier. Locate the adjustable Release Buckle underneath the velcro Storm Flaps and tighten the Waist-Band
until taut around the carrier. Once the Waist-Band is secured, tighten and connect the 2nd Horizontal Support
Strap located above the Waist-Band. Pull the Vertical Support Straps around the underside of the carrier and
back to meet at the top. Connect the Release Buckle and pull tight to secure your HideOut Cover and cargo to
the carrier.
Unfold the included DragNet and drape over top the secured HideOut Cover. Fasten all Molded Clips by
securing and evenly spacing them to anchor points located on the underside of the carrier.
Daily Operation:
Remove your DragNet and completely loosen and disconnect all Release Buckles except for the Waist-Band.
Locate the Coiled Zipper spanning along the top of the HideOut Cover and unzip. Remove or store any
needed cargo or Bicycles, re-zip the HideOut Cover, and reconnect and tighten all release buckles. Reconnect
DragNet.
HideOut Cover & DragNet devices are a weather-
resistant (not water-proof) cargo protectant
system, and not a cargo restraint.
Be sure to remove your DragNet and
completely loosen and disconnect all
HideOut Cover Release Buckles rst before
removing the Cover off your cargo carrier to
avoid damage to your product.
WARNING WARNING
PARTS LIST
Qty Description
1 HideOut Cover
1 DragNet Cargo Netting With Clips
Always check that HideOut Cover, DragNet & stored cargo are fully secured to the carrier before
transit to avoid loss or damage to your product & cargo. Multiple tie-down and strap positions are
located along the BossHog Cargo Carrier for supplemental ratchet and tie-down restraints when
necessary.
WARNING
HIDEOUT COVER & DRAGNET INSTALLATION