Let's Go Aero V-Lectric B01175 User manual

Page 1 of 4
Copyright© 2019, Lets Go Aero, Inc., All rights reserved.
B01175-062019rev
Accessory 2-Bike Expansion Kit for V-Lectric Bicycle Carrier (P/N B01892 sold separately).
Rated for 150 lbs (75 lbs per bicycle).
V-Lectric Expansion Kit
2-Bike Accessory Add-on (for V-Lectric Bicycle Carrier)
Part No. B01175
1
4
8
8
8
4
4
8
2
8
8
2
BASE
HAT BRACKETS
5/16” X 1” CARRIAGE BOLTS
5/16” WASHERS
5/16” NYLOCK NUTS
UPPER WHEEL CRADLE
LOWER WHEEL CRADLE
RUBBER STRAP
WING
CRADLE HOUSING
RETAINER CLIP
WIRE LOCK PIN
PARTS
QTY. DESCRIPTION
NOTICE: All Manual information is subject to change without notice. Revised editions
will be available for free download at LetsGoAero.com. Manual information is considered
factual until made obsolete by a revised version.
Follow this QR-Code or visit
LetsGoAero.com/manuals to check for an updated version:
N
P
Q
U
V
W
X
Y
Z
AA
BB
CC
STEP 1: Preparation
Loosen the Hat Brackets [P] of the Base [N] already installed on
your pre-owned V-Lectric Carrier.
Slide the Base [N] back towards the vehicle and out of the way.
Leave these connections loose at this time.
NOTE: This V-Lectric Expansion Kit add-on MUST position furthest
away from vehicle. The Safety Cable located on the Base included
with your original V-Lectric Carrier [N] MUST be positioned closest
to the vehicle.
NOTE: This manual assumes you
have already assembled your pre-
owned V-Lectric Bicycle Carrier.
[Fg.1]
Revision Date: 06/20/19
N
P

Page 2 of 4
STEP 2 REQUIRED TOOL: 1/2” WRENCH
U
P
V
Q
N
Set the new Base [N] on top of the platform.
Bring each Hat Bracket [P] (four total) up from underneath platform so the Hat
Brackets wrap around the tubes of the platform and align with the holes on the
Base [N].
Using two (2) 5/16in Carriage Bolts [Q], two (2) 5/16in Carriage Washers [U],
and two (2) 5/16in Nylock Nuts [V] per Hat Bracket [P] LOOSELY connect each
Hat Bracket to the Base [N] as shown. [Fg. 2]
Once connected, slide both Bases [N] (both the original base and the new
add-on) back and forth along the assembly and position for desired bicycle
clearances. Once positioned, fully tighten the hardware on BOTH Bases [N].
NOTE: Be sure to avoid positioning the original Base [N] over the warning label
located at the platform tubing. See your original V-Lectric Manual P/N 01892
for more information
[Fg. 2]
Z
AA
AA
AA
AA
AA
STEP 3:
Using one (1) Wing [Z], slide both foam bumpers to the center of the Wing.
Turn the handles on each Cradle Housing [AA] to loosen their grip.
Slide two (2) Cradle Housings [AA] above the foam bumpers and two (2) Cradle
Housings below the foam bumpers.
NOTE: The Cylinders located on each Cradle Housing [AA] MUST rest along the
same sides as the connection hole located at the bottom of the Wing [Z]. [Fg. 3]
NOTE: Position the Cylinders located on each Cradle Housing [AA] so that they
alternate direction as shown.
Retighten each Cradle Housing [AA] handle to secure in place on the Wing [Z].
[Fg. 4]
Repeat this step for the second Wing [Z]. HANDLE
CYLINDER
FOAM
BUMPERS
CONNECTION
HOLE
[Fg. 3]
[Fg. 4]
X
W
STEP 4:
Slide the round end of one (1) Rubber Strap [Y] onto each Upper
Wheel Cradle [W] and Lower Cradle [X]. [Fg. 5]
NOTE: Be sure to slide the Rubber Straps [Y] all the way onto the
cradles so that it tightly rests over the plastic coating of the Wheel
Cradle [W & X].
[Fg. 5]
Y Y

Page 3 of 4
AA
BB
W
Y
Z
STEP 5:
Insert two (2) Upper Wheel Cradles [W] with Rubber Straps [Y]
facing in opposite directions into the Cylinders located on the two
(2) Cradle Housing [AA] installed above the foam bumpers on each
Wing [Z] as shown. [Fg. 6]
Secure each Upper Wheel Cradle [W] with a Retainer Clip [BB].
[Fg. 6]
STEP 13:
Insert two (2) Lower Wheel Cradles [X] with Rubber Straps [Y] facing
in opposite directions into the Cylinders located on the two (2) Cradle
Housing [AA] installed below the foam bumpers on each Wing [Z].
Secure each Lower Wheel Cradle [X] with a Retainer Clip [BB]. [Fg. 7]
[Fg. 7]
X
BB
AA
Y
Z
STEP 14:
Slide both Wings [Z] into the tubes located on the Base [N] aligning
the holes at the bottom of the Wing with holes on the Base.
Thread one (1) Wire Lock Pin [CC] into the holes located on each
Base [N] port securing the Wings to the Base [N]. [Fg. 8 & 9]
NOTE: The Wire Lock Pin [CC] MUST always be threaded through
the hole in the Base [N]
from above/inside the
Base as shown.
[Fg. 8]
[Fg. 9]
CC
N
Z

Page 4 of 4
Always secure each bicycle with all four connections points (two Upper Wheel Cradles & two Lower Cradles).
Do not operate the vehicle unless all connection points are tight and secured. Failure to follow bicycle mounting
procedure may result in damage to carrier, damage to property, bodily injury or death.
Always check and conrm all truck mounting points are tight and fully secured before each transit. Failure to follow
proper installation and equipment checks before transit may result in damage to carrier, damage to property, bodily
injury or death.
WARNING:
WARNING:
To register your product, visit the LetsGoAero.com/registration
Technical Support
For assistance with this product, please contact us:
Let’s Go Aero, Inc.
4474 Barnes Road
Colorado Springs, CO 80917 USA
Phone: [phone] or 719-630-3800
Email: [email protected]
To learn more about our products and stay informed about useful options for transporting all kinds of
gear with your carrier, be sure to visit our website: www.LetsGoAero.com
Patent and trademark protected:
Patent Numbers 8,889,456; 14/546.993; Patents Pending
Copyright© 2019, Lets Go Aero, Inc., All rights reserved.
Operation: Bicycle Mounting
Refer to Page 7 of your original V-Lectric Manual P/N B01892 for proper bicycle mounting procedure.