Let's Go Aero TireBiter V-Rack User manual

Page 1 of 8
TireBiter™
Spare Tire Mount V-Rack™ Carrier for Two Bikes
Part No. B00987
Revision Date: 10/21/19TB-B00987-102119Rev
ASSEMBLY, INSTALLATION, AND OPERATION INSTRUCTIONS
To register your product, visit the LetsGoAero.com/registration
For More Information & Accessories, Visit our Website - www.LetsGoAero.com
For Technical Support & Product Questions Contact Us at 877-464-2376 or 719- 630-3800
Email: [email protected]
Let’s Go Aero, Inc. 4474 Barnes Road Colorado Springs, CO 80917, USA
Patent and trademark protected. Patent Number 8,889,456; Patents Pending.
Maximum load weight limit is 35 lbs per bicycle.
For Rear Mounted Spare Tires.
NOTICE: All Manual information is subject to change without notice. Revised editions
will be available for free download at LetsGoAero.com. Manual information is considered
factual until made obsolete by a revised version.
Follow this QR-Code or visit
LetsGoAero.com/manuals to check for an updated version:
Copyright© 2019, Lets Go Aero, Inc., All rights reserved.
PRODUCT MANUAL
Watch the Assembly Video:
www.LetsGoAero.com/Videos
A
B
C
D
E
F
G
H
J
K
L
M
N
O
1
4
8
4
2
2
2
2
8
4
4
8
8
2
BASE
ANGLE BOLT
1/4” WASHER
1/4” NYLOCK NUT
RATCHET ASSEMBLY
LONG WEBBING STRAP
RATCHET COVERS
WING SUPPORT ARMS
CRADLE HOUSING
UPPER WHEEL CRADLE
LOWER WHEEL CRADLE
RUBBER STRAPS
SMALL RETAINER CLIPS
RING PIN
QTY. DESCRIPTION
PARTS

Page 2 of 8
STEP 1:
STEP 2:
STEP 3:
BACK OF VEHICLE
Install each Ratchet Assembly [E] to the Base [A] on the side of the Base CLOSEST to the “U-Tube” using one (1)
Angle Bolt [B], two (2) 1/4” Washers [C] and one (1) Nylock Nut [D] running through the Base and the small Webbing
Strap attached to the Ratchet Assembly as shown. [Fg. 1 & 2]
In the same manor as STEP 1, install each Long Webbing Strap [F] to the Base [A] on the side of the Base FURTHEST
to the “U-Tube”) using one (1) Angle Bolt [B], two (2) 1/4” Washers [C] and one (1) Nylock Nut [D] running through the
Base and the looped end of the Long Webbing Strap as shown. [Fg. 3 & 4]
Set the Base [A] squarely
centered onto the rear spare
tire of the vehicle.
NOTE: The Ratchet Assembly
[E] located closest to the
U-Tube MUST be mounted
facing away from the vehicle.
[Fg. 5 & 6]
F
A
A
A
A
F
E
C,D
B,C
A
E
B
B
C
C
CA
D
D
B
C
C
F
E
F
C
E
D
U-TUBE
U-TUBE
U-TUBE
[Fg. 1]
[Fg. 3]
[Fg. 5] [Fg. 6]
[Fg. 2]
[Fg. 4]

Page 3 of 8
STEP 4:
STEP 5:
Thread the Long Webbing Strap [F] down and around the inside surface of the tire, then through a corresponding spoke
or slotted hole in the wheel, then back up to meet and engage with the Ratchet Assembly [E].
Run the Long Webbing Strap [F] through the slot in the center rotating spool of the closed Ratchet Assembly [E]. Pull the
webbing strap through until most the slack is removed.
Repeat this install procedure on
the second Ratchet Assembly [E].
[Fg. 7 & 8]
Slide one (1) Ratchet Cover [G] around the
back of each Ratchet Assembly [E].
Finish tightening the Ratchet Assembly [E] in
a progressive and alternating manner, until
the TireBiter Base assembly cannot be moved
on the tire by hand.
Close the Ratchet [E] and fold the excess
length of the Webbing Strap [F] around the
Ratchet Assembly.
Fold the Ratchet Covers around the Ratchet
Assembly to engage the velco covering the
Ratchet Assembly and the Webbing Straps.
[Fg. 9]
IMPORTANT: Before each use, re-check the
tension on the Long Webbing Strap [F] to
ensure it is snug and tight before closing the
Ratchet Covers [G].
F
EG
G
F
E
E
F
[Fg. 8]
[Fg. 9]
[Fg. 7]

Page 4 of 8
L
K
K
K
N
N
Slide the round end of one (1) Rubber Strap [M]
onto each Upper Wheel Cradle [K] and Lower Wheel
Cradle. [Fg. 13]
NOTE: Be sure to slide the Rubber Straps [M] all the
way onto the cradles so that it tightly rests over the
plastic coating of the Wheel Cradle [K & L].
M
M
H
[Fg. 13]
STEP 6:
STEP 7:
STEP 8:
Using one (1) Wing [H], slide both foam
bumpers to the center of the Wing.
Turn the handles on each Cradle Housing [J]
to loosen their grip.
Slide two (2) Cradle Housings [J] above the
foam bumpers and two (2) more Cradle
Housings below the foam bumpers. [Fg. 10,
11 & 12]
NOTE: The cylinders located on each Cradle
Housing [J] MUST rest along the
same sides as the connection hole located at
the bottom of the Wing [J].
NOTE: It is recommended to Position the
cylinders located on each Cradle Housing [J]
so that they alternate direction as shown.
Re-tighten each Cradle Housing [J] handle to
secure in place on the Wing [H].
Repeat this step for the second Wing [H].
HANDLE
CYLINDER
CONNECTION
HOLE
FOAM
BUMPERS
Insert two (2) Upper Wheel Cradles [K] with Rubber Straps [M] facing in
opposite directions into the two (2) Cradle Housing [J] installed above
the foam bumpers on each Wing [H] as shown. [Fg. 14]
Secure each Upper Wheel Cradle [K] with a Retainer Clip [N].
E
H
H
H
J
J
J
J
J
J
J
J
[Fg. 10] [Fg. 11] [Fg. 12]
[Fg. 13]
[Fg. 14]

Page 5 of 8
Slide both Wings [H] onto the
Base [A] aligning the holes at
the bottom of the Wing with
holes on the Base.
Thread one (1) Ring Pin [O]
into the holes located on
each Wing [H] securing the
Wings to the Base [A]. [Fg.
16 & 17]
NOTE: The Ring Pin [O]
MUST always be threaded
through the hole in the Wing
[H] from above/inside the
Base [A] as shown.
NOTE: You can use a
straight tool (such as a
Lower Wheel Cradle [R]) to
tighten the Ring Pins further if
needed.
A
A
O
H
H
[Fg. 16] [Fg. 17]
STEP 9:
STEP 9:
Insert two (2) Lower Wheel Cradles [L] with Rubber Straps [M] facing
in opposite directions into the two (2) Cradle Housing [J] installed
below the foam bumpers on each Wing [H]. [Fg. 15]
Secure each Lower Wheel Cradle [L] with a Retainer Clip [N].
TIP: The TireBiter carrier and mounted bicycles can be locked to the vehicle using a standard cable lock (not
included) by running a cable through the Ring Pins [O], the tire and the mounted bicycles.
L
L
H
N
N
[Fg. 15]

Page 6 of 8
Operation: Bicycle Mounting
Back of Vehicle
Hang bicycles by the tires on the Upper Wheel Cradles [K] with the chain rings to the outside. [Fg. 18 & 19]
Adjust the Foam Bumpers located on the Wings [H] to protect the frame of the bicycle.
IMPORTANT: For two bicycles, position the bicycles facing in opposite directions (front-to-back/back-to-front) with the
chain ring to the outside.
Some adjustment of the Wheel Cradles may be necessary in order to accommodate both bicycles.
Secure by tensioning each Rubber Strap [M] over the top of each tire and engaging a strap hole over the end of the
Upper Wheel Cradle [K] using the tightest hole available. [Fg. 20 & 21]
[Fg. 18] [Fg.19]
[Fg. 20]
[Fg. 21]
K
K
M

Page 7 of 8
Adjusting Position of Bicycles
Slide the Lower Wheel Cradle [L] to meet the
bottom/side of the bicycle tire.
Secure the Lower Wheel Cradle [L] using the same
technique as the Upper Wheel Cradles. [Fg. 22 &
23]
TIP: Pull the Rubber Straps [M] to the outside
edge of the outer edge Lower Cradle [L] to position
bicycles wheels
so the frame
of the bicycle
is pulled away
from the Wings
[H] for wheel
touch only
performance.
[Fg. 23]
To accommodate varying bike sizes, slide the cradle along the wings and re-tighten. [Fg. 24]
TIP: Lower Wheel Cradles [L] can be easily reversed while the bicycle hangs from the Upper Wheel Cradles [M] to the
opposite side of the their housing for quick adjustability. [Fg. 25]
[Fg.23]
[Fg.24]
[Fg.25]
[Fg.22]
L
M

Page 8 of 8
Keep bicycles away from hot exhaust.
Drive conservatively, especially over bumps.
Bicycles should never extend beyond sides of vehicle.
For best weight distribution, always load heaviest bicycles closest to vehicle hitch and lightest bicycles farther away.
Do not use Let’s Go Aero carriers and accessories for purposes other than which they were designed.
Rated for motorized vehicles only; not for use on trailers or towed vehicles.
MAXIMUM WEIGHT CAPACITY LIMIT
The maximum load weight per bicycle is 35 lbs. Do not exceed this weight per bicycle. Failure to follow this guideline will
void the warranty.
The maximum overall weight limit is 35 lbs plus the empty weight of the rack. This limit is always subordinate to the
maximum load recommended by the manufacturer of the vehicle itself. It is always the lower maximum recommended
load that applies. Do not exceed the overall carrying capacity of the rack or the vehicle manufacturer’s spare tire mount
or tailgate limit. Failure to follow these guidelines or the product’s instructions will void the warranty.
WARNING:
Always check that ratchet straps and all bolts and connections are tight and fully secure. Make sure the bicycles
are securely attached to the bicycle rack using all required straps provided. Failure to follow proper installation and
equipment checks before transit may result in damage to carrier, proper, bodily injury, or death.
WARNING:
Car vehicle exhaust can cause a hazard. As a precaution, position bicycles clear of exhaust.
CAUTION:
If a Let’s Go Aero bike rack is found to have a defect in workmanship or material over the lifetime of the original purchaser, Let’s Go
Aero will repair or replace the defect free of charge. This warranty terminates if a purchaser transfers the product to any other person.
The warranty does not cover damage or wear which occurs as a result of day to day use or general wear and tear. No warranty is given
for defects caused by normal wear and tear, cosmetic rust, scratches, accidents, unlawful vehicle operation, or modication of, or any
types of repair of, a load carrier system other than those authorized by Let’s Go Aero.
No warranty is given for defects resulting from conditions beyond Let’s Go Aero’s control including, but not limited to, misuse, overload-
ing, or failure to assemble, mount or use the product in accordance with Let’s Go Aero’s written instructions or guidelines included with
the product or made available to the purchaser.
Subject to the limitations and exclusions described in this warranty, Let’s Go Aero will remedy defects in materials or workmanship by
repairing or replacing any parts diagnosed to be at issue without charge for parts or labor. In the event that a product is defective, the
purchaser should contact the Let’s Go Aero dealer from whom the product was purchased. If the dealer is not able to correct the defect,
the purchaser should contact Let’s Go Aero in writing to [email protected] or by phone at 877-464-237 or 719-630-3800.
In the event that a product needs to be returned to Let’s Go Aero, a Let’s Go Aero technician will provide the purchaser with the appro-
priate mailing address and any additional instructions. Proof of purchase in the form of an original purchase invoice or receipt, and a
detailed description of the defect must be provided. Please note that a Return Merchandise Authorization (RMA) from Let’s Go Aero is
required for any returns.
DISCLAIMER OF LIABILITY REPAIR OR REPLACEMENT OF A DEFECTIVE PRODUCT OR THE ISSUANCE OF A REFUND OR
CREDIT (AS DETERMINED BY LET’S GO AERO) IS A PURCHASER’S EXCLUSIVE REMEDY UNDER THIS WARRANTY. DAMAGE
TO A PURCHASER’S VEHICLE, CARGO AND/OR TO ANY OTHER PERSON OR PROPERTY IS EXCLUDED.
THIS WARRANTY IS EXPRESSLY MADE IN LIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
LET’S GO AERO’S SOLE LIABILITY TO ANY PURCHASER IS LIMITED TO THE REMEDY SET FORTH ABOVE. IN NO EVENT WILL
THULE BE LIABLE FOR ANY LOST PROFITS, LOST SALES, OR FOR ANY CONSEQUENTIAL, DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR PUNITIVE DAMAGES OR FOR ANY OTHER DAMAGES OF ANY KIND OR NATURE.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATIONS MAY NOT BE APPLICABLE. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO
HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
OPERATION GUIDELINES
LET’S GO AERO LIMITED LIFETIME WARRANTY