Leviton Intellect ZLDNK User manual

Intellect™Room Controller
Cat. No. ZLDNK
120-277 VAC, 50/60 Hz
INSTALLATION INSTRUCTIONS ENGLISH
DI-000-ZLDNK-00A
WARNINGS AND CAUTIONS
• TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR
FUSE AND TEST THAT POWER IS OFF BEFORE WIRING!
• To be installed and/or used in accordance with appropriate electrical codes and regulations.
• If you are unsure about any part of these instructions, consult an electrician.
WARNINGS AND CAUTIONS
• Use this device with copper or copper clad wire only.
• Use of metal wall plates requires installation into a metal wall box connected to an earth-ground.
• For indoor applications only.
• Save these instructions.
Intellect™
DESCRIPTION
The Intellect™Room Controller is designed to be used to coordinate and control multiple Intellect fixtures and sensors within a room. It manages all energy management functionality
both as required by code and as desired by the user. All aspects of the system can be configured to meet the specific needs of the end-user and their application. An initial configuration
can be created without any special tools using only the room controller and installed devices within the room. System refinements can be made using the Leviton Intellect app from your
smartphone or other Bluetooth enabled Android or iOS device.
NOTES:
• Installs into standard wall boxes.
• May be multi-ganged.
• Multiple devices may be used within the same room for control from multiple locations.
• Each room requires at least one Room Controller.
Squeeze sides
to release
Line up tabs and
press in side to
attach Factory default button
COLOR CHANGE AND BUTTON KITS
NOTE: Buttons and wallplates can be custom engraved to your specifications.
Contact Leviton for availability and order details. To install a color change kit:
1. Squeeze the sides of the button frame to release snap tabs and remove.
2. Install new buttons and wallplate.
ZLDNK-01W
(one button)
ZLDNK-02W
(two buttons)
ZLDNK-04W
(four buttons)
ZLDNK-08W
(eight buttons)
INSTALLATION
1. TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER at circuit breaker or fuse
and test that power is off before wiring!
2. Remove 3/4" of insulation from each wire lead and connect per diagram. After all
connections have been made, ensure that all wire connectors are firmly attached and
there is no exposed copper.
3. Gently place wires and device into wall box and secure with mounting screws.
4. Install Decora®wallplate. Installation is complete.
* NOTE: This device accepts Decora®wallplates (both types - screwless and with screws).
If screw plates are used, remove the four tabs at the corners of the mounting strap to avoid
interference with the wallplate.
* Remove tabs if
using screw type
wallplate
BK
WH
ZLDNK-01W
Neutral (White)
Line
120-277VAC, 60 Hz
Hot (Black)
SPECIFICATIONS
Input Rating 120-277VAC, 40mA Max, 50/60Hz
Standby Power < 0.5W
Output: None RF Communication Only
RF Communication Intellect for communication to other Intellect devices
Bluetooth for communication to an Android or Apple iOS device
for configuration, monitoring, and control
Agency Listings cULus LISTED Energy Mngt. Equip.
UL 916, E148771
CSA C22.2 No. 205
FCC Part 15, Class B
Energy Code Compliance Title 24, ASHRAE 90.1, IECC, DLC Advanced Lighting Controls
IP Rating IP30
WEB VERSION

FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton Manufacturing of Canada Ltd to the attention of the Quality
Assurance Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone at 1 800 405-5320.
DI-000-ZLDNK-00A© 2017 Leviton Mfg. Co., Inc. For Technical Assistance Call: 1-800-824-3005 (U.S.A. Only) www.leviton.com
FCC COMPLIANCE STATEMENT
Contains Radio Module FCC ID: QGH-DLDNK
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference
at his own expense.
Any changes or modifications not expressly approved by Leviton could void the user’s authority
to operate this equipment.
INDUSTRY CANADA COMPLIANCE STATEMENT:
Contains Radio Module IC: 2473-DLDNK
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired operation
of the device. Any changes or modifications not expressly approved by Leviton could void the
user’s authority to operate this equipment.
This Class B digital apparatus complies with Canadian CAN ICES-3(B)/NMB-3(B).
FCC SUPPLIER’S DECLARATION OF CONFORMITY:
Model ZLDNK – Intellect Room Controller is Manufactured by Leviton Manufacturing Inc. 201 N
Service Rd, Melville, NY 11747.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
RF EXPOSURE AND CO-LOCATION:
To comply with FCC OET Bulletin 65 and ISED RF exposure limits for general population and
uncontrolled exposure, this device shall be installed and operated with a minimum distance of 7.9
inches (20 cm) between the radiator and your body. Also, must not be co-located or operated in
conjunction with any other antenna or transmitter.
For additional Information about Leviton’s Intellect products including information about installation, use case diagrams, solution sheets, and other related products, please
visit www.Leviton.com
LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship
under normal and proper use for five years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement, at its option. For details visit www.
leviton.com or call 1-800-824-3005. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product
is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in
accordance with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and fitness for a particular purpose, but if any implied
warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for a particular purpose, is limited to five years. Leviton
is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or
delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
CONFIGURATION AND PROGRAMMING
1. System Configuration is performed using the Leviton application, Intellect, downloadable from Google Play or the Apple Store, using any Bluetooth enabled Android or iOS Device. Use
the application to:
a) Manually add/remove fixtures from the room
b) Adding additional keypads to the room
c) Change Sensor Parameters like Sensitivity, Timeout, target light level
d) Create user defined groups of fixtures
e) Define Scenes (Meeting, Presentation, Lunch, Dinner, Test, etc.)
f) Monitor Energy Usage and View Energy Usage Trend (on meteorology enabled devices)
2. Factory Default: The room controller can be restored to factory default settings by pushing and holding the factory default button (see figure on prior page for location) for 10 seconds
when the station is powered up. During the restore process, all LED’s on the station will be blinking at you rapidly.
NOTE: Factory default button is located under the buttons on the PCB. To access, the plate and button assembly needs to be removed.
*It should be expected that refinement is required to the initial configuration. Based on some room geometries, the system may not be able to accurately configured itself automatically.
This is a simple process that you will be led through by the Intellect smart device application.
TRADEMARK DISCLAIMER: Use herein of third party trademarks, service marks, trade names, brand names and/or product names are for informational purposes only,
are/may be the trademarks of their respective owners; such use is not meant to imply affiliation, sponsorship, or endorsement.
WEB VERSION

ARTWORK PRINT SPECIFICATIONS
DIMENSIONS / FOLD SCHEME / BINDERY DIAGRAM
PART NUMBER REV DESCRIPTION
Line Screen:
Angle:
Resolution:
Offset Flexo
Other
Body Material:
Bindery
Thickness:
Trim
Perfect Bind
Die cut Saddle Stitch
Drill
Fold
The information in this document is the exclusive PROPRIETARY property of LEVITON MANUFACTURING COMPANY, INC. It is disclosed
with the understanding that acceptance or review by the recipient constitutes an undertaking by the recipient. (1) to hold this information in strict
confidence, and (2) not to disclose, duplicate, copy, modify or use the information for any purpose other than that for which disclosed.
PlantApprovals:
PN-ARN: Pilot Rev:ECR Number:
Released Artwork Format: Production PDF Artwork Release Date:
Artwork Print Specification Sheet Rev A12.eps
PMCQA
Artist:
Notes:
Other
Cust Other
S & A
Mktg Eng
FOR LEVITON USE ONLY
SPECIFICATIONS :
PROCESS :
MANUAL INTERIORS / BINDERY / FOLD SCHEME :
COMMENTS :
For manuals - designates cover specifications
Material:
Thickness:
Finish:
:
Artwork must be printed at 100% (1:1 scale)
Spot
CMYK
1:
4:
3:
2:
Color(s): over
1:
4:
3:
2:
Fonts:
Spot
CMYK
1:
4:
3:
2:
Color(s): over
1:
4:
3:
2:
Fonts:
Fold Line
Die Cut Punch/Drill Hole
Glue
Kiss Cut Cellophane
Fold Line
Perforate
Die Cut
Die Line Key:
DI-000-ZLDNK-00A
40 lb. Black
11
x
Helvetica
Instruction Sheet
x
x
x
xx
x
L. Walsh/Z. Reisman
8.5"
11"
Part No.
FINAL
4.25"
2.75" Part No.
EM0286-5967
D. Buerer
cc: R. Parks
S. Muthu M. Darula
J. Garcia,
cc: L. Pukhrambam
01
4/18/2019
V. LoNigro
xx
M. Blonder
X2
WEB VERSION