Leviton miniZ mZb00-102 User manual

Daylight Harvesting Made Simple.
This user’s guide applies to the following part numbers:
Basic Version, 2 Zone, 2 Relay, 120V or 277V
Basic Version, 2 Zone, 2 Relay, 347V
Dimmed Version, 2 Zone, 2 Relay, 120V or 277V
Dimmed Version, 3 Zone, 1 Relay, 120V or 277V
Description
0
3
2
0
0-10V
Outputs
2
1
2
2
Relay
Outputs
mZb00-102
mZd30-101
mZd20-102
mZb00-C02
Model
Number
Features between models vary. As such, not all information in this manual
applies to all models.
Dimmed Version, 3 Zone, 1 Relay, 347V
Dimmed Version, 2 Zone, 2 Relay, 347V 2
3
2
1
mZd20-C02
mZd30-C01

NOTES

Page 1
PHYSICAL INSTALLATION…………………………………………..…….. 2
CONNECT LINE VOLTAGE………………………………………..………. 4
CONNECT LOW VOLTAGE……………………………………………..…. 6
CONNECT LOW VOLTAGE……………………………………………..…. 8
CONFIGURATION DIP SWITCH SETTINGS – BLOCK ONE………………. 10
CONFIGURATION DIP SWITCH SETTINGS – BLOCK TWO….…………… 12
CONFIGURATION DIP SWITCH SETTINGS – BLOCK THREE……………. 15
CONFIGURATION TRIM POT SETTINGS………………………………….. 16
NOTES: DAYLIGHTING CONFIGURATION………………………………… 18
NOTES: BURN IN& AUTO CAL FEATURES……………………………… 19
WARRANTY……………………………………………………………….. 20
DEFAULT TABLES…………………………………..…………………….. 23
TABLE OF CONTENTS
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
STEP 6
STEP 7
STEP 8
STEP 9
STEP 10

ENCLOSURE FEATURES
The enclosure of the miniZ Power Pack is divided into two compartments.
The Low Voltage Compartment is accessible through the cover-plate.
The High Voltage Compartment is factory sealed and is not accessible.
MOUNTING FEATURES
The Power Pack is suitable for plenum use, indoor only, 0 - 40°C, 5 -
95% humidity without condensation. The supply circuit and load circuits
of the miniZ Power Pack are pre-wired to the control board. Color coded
lead wires are provided for quick connections in a junction box. One ½”
nipple is provided on the top of the Power Pack for this purpose.
There are three concentric knockouts provided in the Low Voltage
Compartment of the miniZ Power Pack. They are combination ½” and ¾”
knockouts. There is one on each of the three external sides of the area.
STEP 1
Page 2
PHYSICAL INSTALLATION

Low Voltage Compartment
This area contains all of the low
voltage terminations required in
the field. All of the configuration
settings are made in this area
as well. Class 2 wiring only.
High Voltage Compartment
This area cannot be accessed in the field.
Lead wires exit the compartment through
the top of the enclosure. There are leads
supplied for field connections to circuits
that energize the miniZ Power Pack and
feed the fluorescent fixture circuits.
Nipple
The fitting on the top of the miniZ Power Pack
attaches directly to a junction box or enclosure.
Two 0.2" mounting holes through the back of the
miniZ low voltage compartment, provide secure
fastening to any flat surface.
Knockouts
There are three concentric
knockouts provided in the Low
Voltage Compartment of the miniZ
Power Pack. They are combination
½” and ¾” knockouts. There is one
on each of the three external sides
of the area.
All connections
are for copper
wire only.
PHYSICAL INSTALLATION
Page 3
Mounting Holes
Two mounting holes are
provided to fasten the
miniZ Power Pack in
place.

CONNECT LINE VOLTAGESTEP 2
JUNCTION BOX
BYOTHERS
SUPPLY CIRCUITS
The Feed Circuit, Relay 1 Line, and
Relay 2 Line can be supplied by the
same circuit or individually. The
connections are made in the junction
box.
All supply circuits must be provided
with a 20A or less branch circuit
overcurrent protection device. Branch
circuit protection for 347V circuits
should be rated at 15A.
Relay 1 Line/Load
Ratings: 20A at 120VAC Tungsten/Ballast
20A at 277VAC Ballast
15A at 347VAC (347V Models Only)
Normally Open, Electrically held.
Color Code: Blue – Line, 12 AWG
Blue – Load, 12 AWG
Control Power Circuit
Voltage Rating: 120 – 277VAC, or
200-347VAC on 347V Models Only
Color Code: Black – Line, 120 – 277VAC, 18 AWG
(120-277V Models Only)
White – Neutral, 18 AWG
Orange – 347VAC, 18 AWG
(347V Models Only)
Load Rating: 10W
Page 4

These circuits must be insulated from
the other wiring even when they are not
being used. Cap off and tape any
unused wires.
Relay 2 Line/Load
Ratings: 20A at 120VAC Tungsten/Ballast
20A at 277VAC Ballast
15A at 347VAC (347VModels Only)
Normally Open, Electrically held.
Color Code: Red – Line, 12 AWG
Red – Load, 12 AWG
Not available on three zone models.
Zone Common
Color Code: Gray – 22 AWG
Not available on Basic Model
Zone 1 Analog Output 0 – 10VDC
Color Code: Violet – 22 AWG
Not available on Basic Model
Zone 2 Analog Output 0 – 10VDC
Color Code: Violet w/White stripe – 22 AWG
Not available on Basic Model
CONNECT LINE VOLTAGE
Page 5
Zone 3 Analog Output 0 – 10VDC
Color Code: White w/Violet stripe – 22 AWG
Only available on Three Zone Model

CONNECT LOW VOLTAGESTEP 3
Page 6
Occupancy Sensor Disabled /
Emergency Input
A
Label: OCC DISABLE / EMERGENCY
Set by DIP Switch: Block 1 Number 1
This is a +24V input signal. Function can be set to
either mode exclusively.
Occupancy Disable Mode
When the input goes high (+24V) the Power Pack
will disable the Occupancy Sensor input and there
will be no change in the current state. When the
input signal is removed, the Occupancy Sensor will
return to the normal mode.
Emergency Mode
Emergency mode is triggered when the emergency
input is connected to the common. When the signal
is received, the Power Pack will turn on all zones
by turning on all relays and raising any 0 – 10V
outputs to 10 V. The Power Pack zones will remain
fully illuminated until the Emergency signal is
removed.
Photocell Disable / Force Off Input
Label: PC DISABLE / FORCE OFF
Set by DIP Switch: Block 1 Number 2
This is a +24V input signal. Function can be set to
either mode exclusively.
Photocell Disable Mode
When the input goes high (+24V) the Power Pack
will disable the Photocell input, along with daylight
operation, and there will be no change in the
current state. The On switch functionality, when the
photocell is disabled, turns lights on to the
maximum level. When the input signal is removed,
the Photocell will return to the normal mode.
Force Off Mode
When the input goes high (+24V) the Power Pack
will turn off all zones. The Power Pack zones will
remain fully off until the Force Off signal is
removed.
B
Time Clock Input
Label: CLOCK
This signal will originate from a supervisory time
clock system and is a +24V input signal. When the
input goes high (+24V) the Power Pack will turn off
all zones. If the Blink Warn function has been
configured, the Power Pack will trigger the Blink
Warn cycle. If a switch is used to turn on the lights
during a period that the time clock has the lights
off, the system will go into a Blink Warn override
mode.
If both the Occupancy Sensor and the Time Clock
inputs are used, an active (+24 VDC) signal at the
Time Clock input only has the affect of changing
an Auto On configuration to a Manual On.
CLoad Shed Input
Label: SHED
This signal would originate from an energy
management system and is a +24V input signal.
When the input goes high (+24V) the Power Pack
will reduce the output load levels based upon the
position of the Shed trim pot.
In the event that you are in daylighting mode and
less artificial light is required to meet the target than
is required by load shed, the lights will remain at the
lower lighting level – meeting the target.
D

CONNECT LOW VOLTAGE
Page 7
STEP 6
All connections
are for copper
wire only.
E
C
B
A
F
D
Label: OCC, +24V, COM
This three position terminal block is dedicated
to the connection of the Occupancy Sensor.
The Occupancy Sensor signal wire connects
to the OCC terminal. This +24V source is
shared with all circuits supplied from the +24V
power supply rated to a maximum of 120 mA.
Occupancy Sensor InputEPhotocell InputF
Label: PHOTO, +24V, COM
This three terminal block is dedicated to the
connection of the Photocell. The Photocell
signal wire connects to the PHOTO terminal.
This +24V source is shared with all circuits
supplied from the +24V power supply rated to
a maximum of 120 mA.

CONNECT LOW VOLTAGESTEP 4
Page 8
Emergency / HVACG
Label: RLY COM, RLY N/O, RLY N/C
There is one Low Voltage relay output rated
for 1A @ 24V which can be switched between
HVAC and Emergency output functionality.
This terminal block is connected to the
Emergency Output / HVAC relay.
Jumper Settings
A three (3) position pin header is located
adjacent to the terminal block. The jumper
configuration of this header determines the
functionality of the relay.
HVAC
A jumper between pins 1 and 2 will result in
HVAC functionality. In this mode the relay will
change state when the room is occupied. In
occupied state NO (normally open) contact is
closed.
Emergency
A jumper between pin 2 and 3 will result in
Emergency output functionality. In this mode
the relay will change state when an
Emergency Input signal is detected. In normal,
non-emergency state the NO (normally open)
contact is closed.
G
H I
Zone Control Outputs
Label: GREY- Common
VIOLET – Signal 0 – 10V
These terminals provide an alternate location for
connecting to the dimming ballast control circuit.
There can be up to three pairs of these
terminals depending on the model of miniZ
Power Pack. The dimming circuit provides the
analog output to control up to 100 dimming
ballasts. The basic version of the miniZ Power
Pack does not have any of these terminals.
H